buslogic.c

Linux Kernel 2.6.9 for OMAP1710

			BusLogic_Error("at PCI Bus %d Device %d I/O Address 0x%X\n", NULL, Bus, Device, IO_Address);
			continue;
		}
		if (BusLogic_GlobalOptions.TraceProbe) {
			BusLogic_Notice("BusLogic: FlashPoint Host Adapter " "detected at\n", NULL);
			BusLogic_Notice("BusLogic: PCI Bus %d Device %d I/O Address " "0x%X PCI Address 0x%X\n", NULL, Bus, Device, IO_Address, PCI_Address);
		}
		if (BusLogic_ProbeInfoCount < BusLogic_MaxHostAdapters) {
			struct BusLogic_ProbeInfo *ProbeInfo = &BusLogic_ProbeInfoList[BusLogic_ProbeInfoCount++];
			ProbeInfo->HostAdapterType = BusLogic_FlashPoint;
			ProbeInfo->HostAdapterBusType = BusLogic_PCI_Bus;
			ProbeInfo->IO_Address = IO_Address;
			ProbeInfo->PCI_Address = PCI_Address;
			ProbeInfo->Bus = Bus;
			ProbeInfo->Device = Device;
			ProbeInfo->IRQ_Channel = IRQ_Channel;
			ProbeInfo->PCI_Device = PCI_Device;
			FlashPointCount++;
		} else
			BusLogic_Warning("BusLogic: Too many Host Adapters " "detected\n", NULL);
#else
		BusLogic_Error("BusLogic: FlashPoint Host Adapter detected at " "PCI Bus %d Device %d\n", NULL, Bus, Device);
		BusLogic_Error("BusLogic: I/O Address 0x%X PCI Address 0x%X, irq %d, " "but FlashPoint\n", NULL, IO_Address, PCI_Address, IRQ_Channel);
		BusLogic_Error("BusLogic: support was omitted in this kernel " "configuration.\n", NULL);
#endif
	}
	/*
	   The FlashPoint BIOS will scan for FlashPoint Host Adapters in the order of
	   increasing PCI Bus and Device Number, so sort the probe information into
	   the same order the BIOS uses.
	 */
	BusLogic_SortProbeInfo(&BusLogic_ProbeInfoList[FlashPointIndex], FlashPointCount);
	return FlashPointCount;
}


/*
  BusLogic_InitializeProbeInfoList initializes the list of I/O Address and Bus
  Probe Information to be checked for potential BusLogic SCSI Host Adapters by
  interrogating the PCI Configuration Space on PCI machines as well as from the
  list of standard BusLogic MultiMaster ISA I/O Addresses.  By default, if both
  FlashPoint and PCI MultiMaster Host Adapters are present, this driver will
  probe for FlashPoint Host Adapters first unless the BIOS primary disk is
  controlled by the first PCI MultiMaster Host Adapter, in which case
  MultiMaster Host Adapters will be probed first.  The BusLogic Driver Options
  specifications "MultiMasterFirst" and "FlashPointFirst" can be used to force
  a particular probe order.
*/

static void __init BusLogic_InitializeProbeInfoList(struct BusLogic_HostAdapter
						    *PrototypeHostAdapter)
{
	/*
	   If a PCI BIOS is present, interrogate it for MultiMaster and FlashPoint
	   Host Adapters; otherwise, default to the standard ISA MultiMaster probe.
	 */
	if (!BusLogic_ProbeOptions.NoProbePCI) {
		if (BusLogic_ProbeOptions.MultiMasterFirst) {
			BusLogic_InitializeMultiMasterProbeInfo(PrototypeHostAdapter);
			BusLogic_InitializeFlashPointProbeInfo(PrototypeHostAdapter);
		} else if (BusLogic_ProbeOptions.FlashPointFirst) {
			BusLogic_InitializeFlashPointProbeInfo(PrototypeHostAdapter);
			BusLogic_InitializeMultiMasterProbeInfo(PrototypeHostAdapter);
		} else {
			int FlashPointCount = BusLogic_InitializeFlashPointProbeInfo(PrototypeHostAdapter);
			int PCIMultiMasterCount = BusLogic_InitializeMultiMasterProbeInfo(PrototypeHostAdapter);
			if (FlashPointCount > 0 && PCIMultiMasterCount > 0) {
				struct BusLogic_ProbeInfo *ProbeInfo = &BusLogic_ProbeInfoList[FlashPointCount];
				struct BusLogic_HostAdapter *HostAdapter = PrototypeHostAdapter;
				struct BusLogic_FetchHostAdapterLocalRAMRequest FetchHostAdapterLocalRAMRequest;
				struct BusLogic_BIOSDriveMapByte Drive0MapByte;
				while (ProbeInfo->HostAdapterBusType != BusLogic_PCI_Bus)
					ProbeInfo++;
				HostAdapter->IO_Address = ProbeInfo->IO_Address;
				FetchHostAdapterLocalRAMRequest.ByteOffset = BusLogic_BIOS_BaseOffset + BusLogic_BIOS_DriveMapOffset + 0;
				FetchHostAdapterLocalRAMRequest.ByteCount = sizeof(Drive0MapByte);
				BusLogic_Command(HostAdapter, BusLogic_FetchHostAdapterLocalRAM, &FetchHostAdapterLocalRAMRequest, sizeof(FetchHostAdapterLocalRAMRequest), &Drive0MapByte, sizeof(Drive0MapByte));
				/*
				   If the Map Byte for BIOS Drive 0 indicates that BIOS Drive 0
				   is controlled by this PCI MultiMaster Host Adapter, then
				   reverse the probe order so that MultiMaster Host Adapters are
				   probed before FlashPoint Host Adapters.
				 */
				if (Drive0MapByte.DiskGeometry != BusLogic_BIOS_Disk_Not_Installed) {
					struct BusLogic_ProbeInfo SavedProbeInfo[BusLogic_MaxHostAdapters];
					int MultiMasterCount = BusLogic_ProbeInfoCount - FlashPointCount;
					memcpy(SavedProbeInfo, BusLogic_ProbeInfoList, BusLogic_ProbeInfoCount * sizeof(struct BusLogic_ProbeInfo));
					memcpy(&BusLogic_ProbeInfoList[0], &SavedProbeInfo[FlashPointCount], MultiMasterCount * sizeof(struct BusLogic_ProbeInfo));
					memcpy(&BusLogic_ProbeInfoList[MultiMasterCount], &SavedProbeInfo[0], FlashPointCount * sizeof(struct BusLogic_ProbeInfo));
				}
			}
		}
	} else
		BusLogic_InitializeProbeInfoListISA(PrototypeHostAdapter);
}


#endif				/* CONFIG_PCI */


/*
  BusLogic_Failure prints a standardized error message, and then returns false.
*/

static boolean BusLogic_Failure(struct BusLogic_HostAdapter *HostAdapter, char *ErrorMessage)
{
	BusLogic_AnnounceDriver(HostAdapter);
	if (HostAdapter->HostAdapterBusType == BusLogic_PCI_Bus) {
		BusLogic_Error("While configuring BusLogic PCI Host Adapter at\n", HostAdapter);
		BusLogic_Error("Bus %d Device %d I/O Address 0x%X PCI Address 0x%X:\n", HostAdapter, HostAdapter->Bus, HostAdapter->Device, HostAdapter->IO_Address, HostAdapter->PCI_Address);
	} else
		BusLogic_Error("While configuring BusLogic Host Adapter at " "I/O Address 0x%X:\n", HostAdapter, HostAdapter->IO_Address);
	BusLogic_Error("%s FAILED - DETACHING\n", HostAdapter, ErrorMessage);
	if (BusLogic_CommandFailureReason != NULL)
		BusLogic_Error("ADDITIONAL FAILURE INFO - %s\n", HostAdapter, BusLogic_CommandFailureReason);
	return false;
}


/*
  BusLogic_ProbeHostAdapter probes for a BusLogic Host Adapter.
*/

static boolean __init BusLogic_ProbeHostAdapter(struct BusLogic_HostAdapter *HostAdapter)
{
	union BusLogic_StatusRegister StatusRegister;
	union BusLogic_InterruptRegister InterruptRegister;
	union BusLogic_GeometryRegister GeometryRegister;
	/*
	   FlashPoint Host Adapters are Probed by the FlashPoint SCCB Manager.
	 */
	if (BusLogic_FlashPointHostAdapterP(HostAdapter)) {
		struct FlashPoint_Info *FlashPointInfo = &HostAdapter->FlashPointInfo;
		FlashPointInfo->BaseAddress = (u32) HostAdapter->IO_Address;
		FlashPointInfo->IRQ_Channel = HostAdapter->IRQ_Channel;
		FlashPointInfo->Present = false;
		if (!(FlashPoint_ProbeHostAdapter(FlashPointInfo) == 0 && FlashPointInfo->Present)) {
			BusLogic_Error("BusLogic: FlashPoint Host Adapter detected at " "PCI Bus %d Device %d\n", HostAdapter, HostAdapter->Bus, HostAdapter->Device);
			BusLogic_Error("BusLogic: I/O Address 0x%X PCI Address 0x%X, " "but FlashPoint\n", HostAdapter, HostAdapter->IO_Address, HostAdapter->PCI_Address);
			BusLogic_Error("BusLogic: Probe Function failed to validate it.\n", HostAdapter);
			return false;
		}
		if (BusLogic_GlobalOptions.TraceProbe)
			BusLogic_Notice("BusLogic_Probe(0x%X): FlashPoint Found\n", HostAdapter, HostAdapter->IO_Address);
		/*
		   Indicate the Host Adapter Probe completed successfully.
		 */
		return true;
	}
	/*
	   Read the Status, Interrupt, and Geometry Registers to test if there are I/O
	   ports that respond, and to check the values to determine if they are from a
	   BusLogic Host Adapter.  A nonexistent I/O port will return 0xFF, in which
	   case there is definitely no BusLogic Host Adapter at this base I/O Address.
	   The test here is a subset of that used by the BusLogic Host Adapter BIOS.
	 */
	StatusRegister.All = BusLogic_ReadStatusRegister(HostAdapter);
	InterruptRegister.All = BusLogic_ReadInterruptRegister(HostAdapter);
	GeometryRegister.All = BusLogic_ReadGeometryRegister(HostAdapter);
	if (BusLogic_GlobalOptions.TraceProbe)
		BusLogic_Notice("BusLogic_Probe(0x%X): Status 0x%02X, Interrupt 0x%02X, " "Geometry 0x%02X\n", HostAdapter, HostAdapter->IO_Address, StatusRegister.All, InterruptRegister.All, GeometryRegister.All);
	if (StatusRegister.All == 0 || StatusRegister.sr.DiagnosticActive || StatusRegister.sr.CommandParameterRegisterBusy || StatusRegister.sr.Reserved || StatusRegister.sr.CommandInvalid || InterruptRegister.ir.Reserved != 0)
		return false;
	/*
	   Check the undocumented Geometry Register to test if there is an I/O port
	   that responded.  Adaptec Host Adapters do not implement the Geometry
	   Register, so this test helps serve to avoid incorrectly recognizing an
	   Adaptec 1542A or 1542B as a BusLogic.  Unfortunately, the Adaptec 1542C
	   series does respond to the Geometry Register I/O port, but it will be
	   rejected later when the Inquire Extended Setup Information command is
	   issued in BusLogic_CheckHostAdapter.  The AMI FastDisk Host Adapter is a
	   BusLogic clone that implements the same interface as earlier BusLogic
	   Host Adapters, including the undocumented commands, and is therefore
	   supported by this driver.  However, the AMI FastDisk always returns 0x00
	   upon reading the Geometry Register, so the extended translation option
	   should always be left disabled on the AMI FastDisk.
	 */
	if (GeometryRegister.All == 0xFF)
		return false;
	/*
	   Indicate the Host Adapter Probe completed successfully.
	 */
	return true;
}


/*
  BusLogic_HardwareResetHostAdapter issues a Hardware Reset to the Host Adapter
  and waits for Host Adapter Diagnostics to complete.  If HardReset is true, a
  Hard Reset is performed which also initiates a SCSI Bus Reset.  Otherwise, a
  Soft Reset is performed which only resets the Host Adapter without forcing a
  SCSI Bus Reset.
*/

static boolean BusLogic_HardwareResetHostAdapter(struct BusLogic_HostAdapter
						 *HostAdapter, boolean HardReset)
{
	union BusLogic_StatusRegister StatusRegister;
	int TimeoutCounter;
	/*
	   FlashPoint Host Adapters are Hard Reset by the FlashPoint SCCB Manager.
	 */
	if (BusLogic_FlashPointHostAdapterP(HostAdapter)) {
		struct FlashPoint_Info *FlashPointInfo = &HostAdapter->FlashPointInfo;
		FlashPointInfo->HostSoftReset = !HardReset;
		FlashPointInfo->ReportDataUnderrun = true;
		HostAdapter->CardHandle = FlashPoint_HardwareResetHostAdapter(FlashPointInfo);
		if (HostAdapter->CardHandle == FlashPoint_BadCardHandle)
			return false;
		/*
		   Indicate the Host Adapter Hard Reset completed successfully.
		 */
		return true;
	}
	/*
	   Issue a Hard Reset or Soft Reset Command to the Host Adapter.  The Host
	   Adapter should respond by setting Diagnostic Active in the Status Register.
	 */
	if (HardReset)
		BusLogic_HardReset(HostAdapter);
	else
		BusLogic_SoftReset(HostAdapter);
	/*
	   Wait until Diagnostic Active is set in the Status Register.
	 */
	TimeoutCounter = 5 * 10000;
	while (--TimeoutCounter >= 0) {
		StatusRegister.All = BusLogic_ReadStatusRegister(HostAdapter);
		if (StatusRegister.sr.DiagnosticActive)
			break;
		udelay(100);
	}
	if (BusLogic_GlobalOptions.TraceHardwareReset)
		BusLogic_Notice("BusLogic_HardwareReset(0x%X): Diagnostic Active, " "Status 0x%02X\n", HostAdapter, HostAdapter->IO_Address, StatusRegister.All);
	if (TimeoutCounter < 0)
		return false;
	/*
	   Wait 100 microseconds to allow completion of any initial diagnostic
	   activity which might leave the contents of the Status Register
	   unpredictable.
	 */
	udelay(100);
	/*
	   Wait until Diagnostic Active is reset in the Status Register.
	 */
	TimeoutCounter = 10 * 10000;
	while (--TimeoutCounter >= 0) {
		StatusRegister.All = BusLogic_ReadStatusRegister(HostAdapter);
		if (!StatusRegister.sr.DiagnosticActive)
			break;
		udelay(100);
	}
	if (BusLogic_GlobalOptions.TraceHardwareReset)
		BusLogic_Notice("BusLogic_HardwareReset(0x%X): Diagnostic Completed, " "Status 0x%02X\n", HostAdapter, HostAdapter->IO_Address, StatusRegister.All);
	if (TimeoutCounter < 0)
		return false;
	/*
	   Wait until at least one of the Diagnostic Failure, Host Adapter Ready,
	   or Data In Register Ready bits is set in the Status Register.
	 */
	TimeoutCounter = 10000;
	while (--TimeoutCounter >= 0) {
		StatusRegister.All = BusLogic_ReadStatusRegister(HostAdapter);
		if (StatusRegister.sr.DiagnosticFailure || StatusRegister.sr.HostAdapterReady || StatusRegister.sr.DataInRegisterReady)
			break;
		udelay(100);
	}
	if (BusLogic_GlobalOptions.TraceHardwareReset)
		BusLogic_Notice("BusLogic_HardwareReset(0x%X): Host Adapter Ready, " "Status 0x%02X\n", HostAdapter, HostAdapter->IO_Address, StatusRegister.All);
	if (TimeoutCounter < 0)
		return false;
	/*
	   If Diagnostic Failure is set or Host Adapter Ready is reset, then an
	   error occurred during the Host Adapter diagnostics.  If Data In Register
	   Ready is set, then there is an Error Code available.
	 */
	if (StatusRegister.sr.DiagnosticFailure || !StatusRegister.sr.HostAdapterReady) {
		BusLogic_CommandFailureReason = NULL;
		BusLogic_Failure(HostAdapter, "HARD RESET DIAGNOSTICS");
		BusLogic_Error("HOST ADAPTER STATUS REGISTER = %02X\n", HostAdapter, StatusRegister.All);
		if (StatusRegister.sr.DataInRegisterReady) {
			unsigned char ErrorCode = BusLogic_ReadDataInRegister(HostAdapter);
			BusLogic_Error("HOST ADAPTER ERROR CODE = %d\n", HostAdapter, ErrorCode);
		}
		return false;
	}
	/*
	   Indicate the Host Adapter Hard Reset completed successfully.
	 */
	return true;
}


/*
  BusLogic_CheckHostAdapter checks to be sure this really is a BusLogic
  Host Adapter.
*/

static boolean __init BusLogic_CheckHostAdapter(struct BusLogic_HostAdapter *HostAdapter)
{
	struct BusLogic_ExtendedSetupInformation ExtendedSetupInformation;
	unsigned char RequestedReplyLength;
	boolean Result = true;
	/*
	   FlashPoint Host Adapters do not require this protection.
	 */
	if (BusLogic_FlashPointHostAdapterP(HostAdapter))
		return true;
	/*
	   Issue the Inquire Extended Setup Information command.  Only genuine
	   BusLogic Host Adapters and true clones support this command.  Adaptec 1542C
	   series Host Adapters that respond to the Geometry Register I/O port will
	   fail this command.
	 */
	RequestedReplyLength = sizeof(ExtendedSetupInformation);