timer_tsc.c

来自「Linux Kernel 2.6.9 for OMAP1710」· C语言 代码 · 共 557 行 · 第 1/2 页

	    (val == CPUFREQ_POSTCHANGE && freq->old > freq->new) ||
	    (val == CPUFREQ_RESUMECHANGE)) {
		if (!(freq->flags & CPUFREQ_CONST_LOOPS))
			cpu_data[freq->cpu].loops_per_jiffy = cpufreq_scale(loops_per_jiffy_ref, ref_freq, freq->new);
#ifndef CONFIG_SMP
		if (cpu_khz)
			cpu_khz = cpufreq_scale(cpu_khz_ref, ref_freq, freq->new);
		if (use_tsc) {
			if (!(freq->flags & CPUFREQ_CONST_LOOPS)) {
				fast_gettimeoffset_quotient = cpufreq_scale(fast_gettimeoffset_ref, freq->new, ref_freq);
				set_cyc2ns_scale(cpu_khz/1000);
			}
		}
#endif
	}

	if (val != CPUFREQ_RESUMECHANGE)
		write_sequnlock_irq(&xtime_lock);

	return 0;
}

static struct notifier_block time_cpufreq_notifier_block = {
	.notifier_call	= time_cpufreq_notifier
};


static int __init cpufreq_tsc(void)
{
	int ret;
	INIT_WORK(&cpufreq_delayed_get_work, handle_cpufreq_delayed_get, NULL);
	ret = cpufreq_register_notifier(&time_cpufreq_notifier_block,
					CPUFREQ_TRANSITION_NOTIFIER);
	if (!ret)
		cpufreq_init = 1;
	return ret;
}
core_initcall(cpufreq_tsc);

#else /* CONFIG_CPU_FREQ */
static inline void cpufreq_delayed_get(void) { return; }
#endif 

static void mark_offset_tsc(void)
{
	unsigned long lost,delay;
	unsigned long delta = last_tsc_low;
	int count;
	int countmp;
	static int count1 = 0;
	unsigned long long this_offset, last_offset;
	static int lost_count = 0;

	write_seqlock(&monotonic_lock);
	last_offset = ((unsigned long long)last_tsc_high<<32)|last_tsc_low;
	/*
	 * It is important that these two operations happen almost at
	 * the same time. We do the RDTSC stuff first, since it's
	 * faster. To avoid any inconsistencies, we need interrupts
	 * disabled locally.
	 */

	/*
	 * Interrupts are just disabled locally since the timer irq
	 * has the SA_INTERRUPT flag set. -arca
	 */

	/* read Pentium cycle counter */

	rdtsc(last_tsc_low, last_tsc_high);

	spin_lock(&i8253_lock);
	outb_p(0x00, PIT_MODE);     /* latch the count ASAP */

	count = inb_p(PIT_CH0);    /* read the latched count */
	count |= inb(PIT_CH0) << 8;

	/*
	 * VIA686a test code... reset the latch if count > max + 1
	 * from timer_pit.c - cjb
	 */
	if (count > LATCH) {
		outb_p(0x34, PIT_MODE);
		outb_p(LATCH & 0xff, PIT_CH0);
		outb(LATCH >> 8, PIT_CH0);
		count = LATCH - 1;
	}

	spin_unlock(&i8253_lock);

	if (pit_latch_buggy) {
		/* get center value of last 3 time lutch */
		if ((count2 >= count && count >= count1)
		    || (count1 >= count && count >= count2)) {
			count2 = count1; count1 = count;
		} else if ((count1 >= count2 && count2 >= count)
			   || (count >= count2 && count2 >= count1)) {
			countmp = count;count = count2;
			count2 = count1;count1 = countmp;
		} else {
			count2 = count1; count1 = count; count = count1;
		}
	}

	/* lost tick compensation */
	delta = last_tsc_low - delta;
	{
		register unsigned long eax, edx;
		eax = delta;
		__asm__("mull %2"
		:"=a" (eax), "=d" (edx)
		:"rm" (fast_gettimeoffset_quotient),
		 "0" (eax));
		delta = edx;
	}
	delta += delay_at_last_interrupt;
	lost = delta/(1000000/HZ);
	delay = delta%(1000000/HZ);
	if (lost >= 2) {
		jiffies_64 += lost-1;

		/* sanity check to ensure we're not always losing ticks */
		if (lost_count++ > 100) {
			printk(KERN_WARNING "Losing too many ticks!\n");
			printk(KERN_WARNING "TSC cannot be used as a timesource.  \n");
			printk(KERN_WARNING "Possible reasons for this are:\n");
			printk(KERN_WARNING "  You're running with Speedstep,\n");
			printk(KERN_WARNING "  You don't have DMA enabled for your hard disk (see hdparm),\n");
			printk(KERN_WARNING "  Incorrect TSC synchronization on an SMP system (see dmesg).\n");
			printk(KERN_WARNING "Falling back to a sane timesource now.\n");

			clock_fallback();
		}
		/* ... but give the TSC a fair chance */
		if (lost_count > 25)
			cpufreq_delayed_get();
	} else
		lost_count = 0;
	/* update the monotonic base value */
	this_offset = ((unsigned long long)last_tsc_high<<32)|last_tsc_low;
	monotonic_base += cycles_2_ns(this_offset - last_offset);
	write_sequnlock(&monotonic_lock);

	/* calculate delay_at_last_interrupt */
	count = ((LATCH-1) - count) * TICK_SIZE;
	delay_at_last_interrupt = (count + LATCH/2) / LATCH;

	/* catch corner case where tick rollover occured
	 * between tsc and pit reads (as noted when
	 * usec delta is > 90% # of usecs/tick)
	 */
	if (lost && abs(delay - delay_at_last_interrupt) > (900000/HZ))
		jiffies_64++;
}

static int __init init_tsc(char* override)
{

	/* check clock override */
	if (override[0] && strncmp(override,"tsc",3)) {
#ifdef CONFIG_HPET_TIMER
		if (is_hpet_enabled()) {
			printk(KERN_ERR "Warning: clock= override failed. Defaulting to tsc\n");
		} else
#endif
		{
			return -ENODEV;
		}
	}

	/*
	 * If we have APM enabled or the CPU clock speed is variable
	 * (CPU stops clock on HLT or slows clock to save power)
	 * then the TSC timestamps may diverge by up to 1 jiffy from
	 * 'real time' but nothing will break.
	 * The most frequent case is that the CPU is "woken" from a halt
	 * state by the timer interrupt itself, so we get 0 error. In the
	 * rare cases where a driver would "wake" the CPU and request a
	 * timestamp, the maximum error is < 1 jiffy. But timestamps are
	 * still perfectly ordered.
	 * Note that the TSC counter will be reset if APM suspends
	 * to disk; this won't break the kernel, though, 'cuz we're
	 * smart.  See arch/i386/kernel/apm.c.
	 */
 	/*
 	 *	Firstly we have to do a CPU check for chips with
 	 * 	a potentially buggy TSC. At this point we haven't run
 	 *	the ident/bugs checks so we must run this hook as it
 	 *	may turn off the TSC flag.
 	 *
 	 *	NOTE: this doesn't yet handle SMP 486 machines where only
 	 *	some CPU's have a TSC. Thats never worked and nobody has
 	 *	moaned if you have the only one in the world - you fix it!
 	 */

	count2 = LATCH; /* initialize counter for mark_offset_tsc() */

	if (cpu_has_tsc) {
		unsigned long tsc_quotient;
#ifdef CONFIG_HPET_TIMER
		if (is_hpet_enabled()){
			unsigned long result, remain;
			printk("Using TSC for gettimeofday\n");
			tsc_quotient = calibrate_tsc_hpet(NULL);
			timer_tsc.mark_offset = &mark_offset_tsc_hpet;
			/*
			 * Math to calculate hpet to usec multiplier
			 * Look for the comments at get_offset_tsc_hpet()
			 */
			ASM_DIV64_REG(result, remain, hpet_tick,
					0, KERNEL_TICK_USEC);
			if (remain > (hpet_tick >> 1))
				result++; /* rounding the result */

			hpet_usec_quotient = result;
		} else
#endif
		{
			tsc_quotient = calibrate_tsc();
		}

		if (tsc_quotient) {
			fast_gettimeoffset_quotient = tsc_quotient;
			use_tsc = 1;
			/*
			 *	We could be more selective here I suspect
			 *	and just enable this for the next intel chips ?
			 */
			/* report CPU clock rate in Hz.
			 * The formula is (10^6 * 2^32) / (2^32 * 1 / (clocks/us)) =
			 * clock/second. Our precision is about 100 ppm.
			 */
			{	unsigned long eax=0, edx=1000;
				__asm__("divl %2"
		       		:"=a" (cpu_khz), "=d" (edx)
        	       		:"r" (tsc_quotient),
	                	"0" (eax), "1" (edx));
				printk("Detected %lu.%03lu MHz processor.\n", cpu_khz / 1000, cpu_khz % 1000);
			}
			set_cyc2ns_scale(cpu_khz/1000);
			return 0;
		}
	}
	return -ENODEV;
}

#ifndef CONFIG_X86_TSC
/* disable flag for tsc.  Takes effect by clearing the TSC cpu flag
 * in cpu/common.c */
static int __init tsc_setup(char *str)
{
	tsc_disable = 1;
	return 1;
}
#else
static int __init tsc_setup(char *str)
{
	printk(KERN_WARNING "notsc: Kernel compiled with CONFIG_X86_TSC, "
				"cannot disable TSC.\n");
	return 1;
}
#endif
__setup("notsc", tsc_setup);



/************************************************************/

/* tsc timer_opts struct */
struct timer_opts timer_tsc = {
	.name = 	"tsc",
	.init =		init_tsc,
	.mark_offset =	mark_offset_tsc, 
	.get_offset =	get_offset_tsc,
	.monotonic_clock =	monotonic_clock_tsc,
	.delay = delay_tsc,
};