ptc_xctu_802_15_4.prm

nRF24E1 sample xBee development

/*************************************************************
* This file contains some basic linker parameters.
*
*************************************************************/

NAMES
// Do not remove this block/section.
// Description: The NAMES block contains a list of binary files building the application. This block
// is mandatory and can only be specified once in a prm file.
// Additional files may be specified by the option -Add. The object files specified with the option
// -Add are linked before the files mentioned in the NAMES block. With the option -Add, additional
// files can be added to a project without modifying the link parameter file.
// If all binary files should be specified by the command line option -add, then an empty NAMES
// block (just NAMES END) must be present in the link parameter file. Object files added with this
// option are linked before the object files specified in the NAMES block.
END

// **************************************************************************

// Memory map for HCS08 GB60. All memory areas are define below i.e. registers and stack etc.
// are shown.

// Options
// READ_WRITE	is for normal variables
// READ_ONLY	is for const variables and code
// NO_INIT	is for uninitialized variables.

SECTIONS 
	DIRECT_PAGE_REGISTERS	      = READ_WRITE 0x0000 TO 0x007F; // This section contains often used registers
	DIRECT_ADDRESSING_MEMORY    = READ_WRITE 0x0080 TO 0x00FF; // Direct addressing memory
	USER_STACK		              = READ_WRITE 0x0100 TO 0x02BF; // User stack
	STATIC_USER_MEMORY	        = READ_WRITE 0x02C0 TO 0x107D; // Static user memory

	// Reserve space for NV RAM pointer
	NV_RAM_POINTER_RAM          = NO_INIT    0x107E TO 0x107F; // Static user memory

	FLASH 			                = READ_ONLY  0x1080 TO 0x13FF; // Flash section

	// BootLoader/802.15.4/App. NV RAM flash memory.
	// Initialized by 802.15.4.
	BOOTLOADER_MAC_NV_RAM0      = READ_ONLY 0x01400 TO 0x148C;  // Flash memory
	BOOTLOADER_PHY_NV_RAM0      = READ_ONLY 0x0148D TO 0x14BB;  // Flash memory
	BOOTLOADER_APP_NV_RAM0      = READ_ONLY 0x014BC TO 0x15FF;  // Flash memory
	BOOTLOADER_APP_NV_RAM1      = NO_INIT   0x01600 TO 0x17FF;  // Flash memory (erased)

	HIGH_PAGE_REGISTERS	        = READ_WRITE 0x1800 TO 0x182B; // High page register section
	FLASH2			                = READ_ONLY  0x182C TO 0xFDBE; // Flash section
	NV_REGISTERS		            = READ_ONLY  0xFFB0 TO 0xFFBF; // None-volatile registers
	IRQ_VECTORS_TABLE	          = READ_ONLY  0xFDC0 TO 0xFDFD; // ISR vectors
	RESET_VECTOR		            = READ_ONLY  0xFDFE TO 0xFDFF; // System reset vector

END

// **************************************************************************

// Here it is listed how the variables and code must be allocated.
PLACEMENT
	MY_ZEROPAGE                 INTO DIRECT_ADDRESSING_MEMORY;
	DEFAULT_RAM                 INTO STATIC_USER_MEMORY;
	DEFAULT_ROM		              INTO FLASH, FLASH2;
	SSTACK 			                INTO USER_STACK; // Put stack in user stack section
	NV_RAM_POINTER			        INTO NV_RAM_POINTER_RAM;
	BOOTLOADER_MAC_NV_DATA0	    INTO BOOTLOADER_MAC_NV_RAM0;
	BOOTLOADER_PHY_NV_DATA0	    INTO BOOTLOADER_PHY_NV_RAM0;
	BOOTLOADER_APP_NV_DATA0     INTO BOOTLOADER_APP_NV_RAM0;
	BOOTLOADER_APP_NV_DATA1     INTO BOOTLOADER_APP_NV_RAM1;
	NV_REGISTERS_SECTION        INTO NV_REGISTERS;
	IRQ_VECTOR_SECTION	        INTO IRQ_VECTORS_TABLE;
	RESET_VECTOR_SECTION	      INTO RESET_VECTOR;
END

// **************************************************************************