📄 nscrtv-hfcems-opticaltransmitterdirectly-mib.txt

📁 内有HFC网管系统中所要管理设备的MIB库资料
💻 TXT
字号:
NSCRTV-HFCEMS-OPTICALTRANSMITTERDIRECTLY-MIB DEFINITIONS::=BEGIN
   IMPORTS
      OBJECT-TYPE       
         FROM RFC-1212
      DisplayString 
         FROM RFC1213-MIB
      otdIdent
         FROM NSCRTV-ROOT
;
otdVendorOID OBJECT-TYPE
   SYNTAX OBJECT IDENTIFIER
   ACCESS read-only
   STATUS optional
   DESCRIPTION
"此对象提供厂商对直接调制光发送机MIB的扩充，无扩充时此对象应指向直接调制光发送
机节点otdIdent。"
   ::={ otdIdent 1 }

otdSlotNumber OBJECT-TYPE
   SYNTAX INTEGER ( 0..32767 )
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
"下行光发送机数量或机架插槽数量。"
   ::={ otdIdent 2 }

otdOptDeviceTable OBJECT-TYPE
   SYNTAX SEQUENCE OF OtdOptDeviceEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
"下行光发送机信息表。"
   ::={ otdIdent 3 }

otdOptDeviceEntry OBJECT-TYPE
   SYNTAX OtdOptDeviceEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
"下行光发送机信息表目。"
   INDEX { otdIndex }
   ::={ otdOptDeviceTable 1 }

OtdOptDeviceEntry::=
   SEQUENCE
   {
   otdIndex
      INTEGER,
   otdLaserWavelength
      DisplayString,
   otdLaserType
      DisplayString,
   otdDriveLevel
      INTEGER,
   otdInputRFLevel
      INTEGER,
   otdInputRFAttenuationArea
      INTEGER,
   otdInputRFAttenuation
      INTEGER,
   otdLaserTemp
      INTEGER,
   otdLaserCurrent
      INTEGER,
   otdOpicalOutputPower
      INTEGER,
   otdTecCurrent
      INTEGER,
   otdAGCControl
      INTEGER,
   otdConfigurationDriveLevel
      INTEGER,
   otdConfigurationRFAttenuation
      INTEGER,
   otdConfigurationRFChannels
      INTEGER
   }

otdIndex OBJECT-TYPE
   SYNTAX INTEGER ( 0..32767 )
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"下行光发送机索引,可以是光发送机编号或机架插槽号。"
   ::={ otdOptDeviceEntry 1 }

otdLaserWavelength OBJECT-TYPE
   SYNTAX DisplayString
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"激光器波长。"
   ::={ otdOptDeviceEntry 2 }

otdLaserType OBJECT-TYPE
   SYNTAX DisplayString
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"激光器类型，有效值为unisolated FP, isolated FP, uncooled DFB, cooled DFB,ITU
等。"
   ::={ otdOptDeviceEntry 3 }

otdDriveLevel OBJECT-TYPE
   SYNTAX INTEGER ( 0..127 )
   ACCESS read-write
   STATUS optional
   DESCRIPTION
"光模块激励电平,单位为dBuV/ch。此对象要求在属性MIB中登记一个条目。"
   ::={ otdOptDeviceEntry 4 }

otdInputRFLevel OBJECT-TYPE
   SYNTAX INTEGER ( 0..127 )
   ACCESS read-only
   STATUS optional
   DESCRIPTION
"输入射频信号电平,单位为dBuV/ch。此对象要求在属性MIB中登记一个条目。"
   ::={ otdOptDeviceEntry 5 }

otdInputRFAttenuationArea OBJECT-TYPE
   SYNTAX INTEGER ( 0..20 )
   ACCESS read-write
   STATUS optional
   DESCRIPTION
"输入射频信号衰减量范围,单位为dB。"
   ::={ otdOptDeviceEntry 6 }

otdInputRFAttenuation OBJECT-TYPE
   SYNTAX INTEGER ( -32768..32767 )
   ACCESS read-write
   STATUS optional
   DESCRIPTION
"输入射频信号衰减量,单位为0.1dB。"
   ::={ otdOptDeviceEntry 7 }

otdLaserTemp OBJECT-TYPE
   SYNTAX INTEGER ( -32768..32767 )
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"激光器工作温度,单位为0.1摄氏度。此对象要求在属性MIB中登记一个条目。"
   ::={ otdOptDeviceEntry 8 }

otdLaserCurrent OBJECT-TYPE
   SYNTAX INTEGER ( -32768..32767 )
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"激光器工作电流,单位为0.1mA。此对象要求在属性MIB中登记一个条目。"
   ::={ otdOptDeviceEntry 9 }

otdOpicalOutputPower OBJECT-TYPE
   SYNTAX INTEGER ( 0..32767 )
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"输出光功率,单位为0.1mW。此对象要求在属性MIB中登记一个条目。"
   ::={ otdOptDeviceEntry 10 }

otdTecCurrent OBJECT-TYPE
   SYNTAX INTEGER ( -32768..32767 )
   ACCESS read-only
   STATUS optional
   DESCRIPTION
"激光器制冷电流,单位为0.01A。此对象要求在属性MIB中登记一个条目。"
   ::={ otdOptDeviceEntry 11 }

otdAGCControl OBJECT-TYPE
   SYNTAX INTEGER {off(1),on(2)}
   ACCESS read-write
   STATUS optional
   DESCRIPTION
"AGC控制使能。"
   ::={ otdOptDeviceEntry 12 }

otdConfigurationDriveLevel OBJECT-TYPE
   SYNTAX INTEGER 
   ACCESS read-write
   STATUS optional
   DESCRIPTION
"设定激光器RF驱动电平偏移量，单位为0.1dB。该参数仅在AGC模式为打开时起作用。
系统根据该设定自动调整RF增益（衰减），从而达到设定的激光器RF驱动电平偏移量。
"
   ::={ otdOptDeviceEntry 13 }

otdConfigurationRFAttenuation OBJECT-TYPE
   SYNTAX INTEGER 
   ACCESS read-write
   STATUS optional
   DESCRIPTION
"设定激光器RF驱动信号增益（衰减）的偏移量，单位为0.1dB。该参数仅在AGC模式为
关闭时起作用（MGC）。系统根据该设定调整RF信道的增益（衰减），从而达到手动
控制激光器RF驱动电平的目的。"
   ::={ otdOptDeviceEntry 14 }

otdConfigurationRFChannels OBJECT-TYPE
   SYNTAX INTEGER 
   ACCESS read-write
   STATUS optional
   DESCRIPTION
"RF信号中输入的电视信号频道数。"
   ::={ otdOptDeviceEntry 15 }

otdFansNumber OBJECT-TYPE
   SYNTAX INTEGER 
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"表示内部散热风扇的数量，‘0’表示设备不支持散热风扇的监测或没有散热风扇。"
   ::={ otdIdent 4 }

otdFansTable OBJECT-TYPE
   SYNTAX SEQUENCE OF OtdFansEntry
   ACCESS not-accessible
   STATUS optional
   DESCRIPTION
"散热风扇信息表。"
   ::={ otdIdent 5 }

otdFansEntry OBJECT-TYPE
   SYNTAX OtdFansEntry
   ACCESS not-accessible
   STATUS optional
   DESCRIPTION
"散热风扇信息表目。"
   INDEX { otdFansIndex }
   ::= { otdFansTable 1 }

otdFansEntry::=SEQUENCE {
   otdFansIndex
      INTEGER,
   otdFansState
      INTEGER,
   otdFansSpeed
      INTEGER,
   otdFansControl
      INTEGER,
   otdFansName
      DisplayString
}

otdFansIndex OBJECT-TYPE
   SYNTAX INTEGER 
   ACCESS read-only
   STATUS optional
   DESCRIPTION
"散热风扇信息表索引。"
  ::={ otdFansEntry 1 }

otdFansState OBJECT-TYPE
   SYNTAX INTEGER { normal (1),fault (2) }
   ACCESS read-only
   STATUS optional
   DESCRIPTION
"散热风扇工作状态，normal 表示正常, fault表示失效。此对象要求在离散属性MIB中登
记一个条目。"
   ::={ otdFansEntry 2 }

otdFansSpeed OBJECT-TYPE
   SYNTAX INTEGER 
   ACCESS read-only
   STATUS optional
   DESCRIPTION
"散热风扇工作时的转速，单位为转/分，不支持转速检测时可置为‘0’。此对象要求在
离散属性MIB中登记一个条目。"
   ::={ otdFansEntry 3 }

otdFansControl OBJECT-TYPE
   SYNTAX INTEGER { on (1),off (2) }
   ACCESS read-write
   STATUS optional
   DESCRIPTION
"散热风扇工作控制。 "
   ::={ otdFansEntry 4 }

otdFansName OBJECT-TYPE
   SYNTAX DisplayString
   ACCESS read-only
   STATUS optional
   DESCRIPTION
"散热风扇名称。"
   ::={ otdFansEntry 5 }

otdNumberDCPowerSupply OBJECT-TYPE
   SYNTAX INTEGER (0..16)
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"直流电源数量，‘0’表示应答器不支持此功能。"
   ::={ otdIdent 6 }

otdDCPowerSupplyMode OBJECT-TYPE
   SYNTAX INTEGER { loadsharing(1),switchedredundant(2),alonesupply(3) }
   ACCESS read-only
   STATUS optional
   DESCRIPTION
"供电电源工作模式。"
   ::={ otdIdent 7 }

otdDCPowerTable OBJECT-TYPE
   SYNTAX SEQUENCE OF OtdDCPowerEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
"直流电源信息表。"
   ::={ otdIdent 8 }

otdDCPowerEntry OBJECT-TYPE
   SYNTAX OtdDCPowerEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
"直流电源信息表目。"
   INDEX { otdDCPowerIndex }
   ::={ otdDCPowerTable 1 }

OtdDCPowerEntry::=
   SEQUENCE
   {
      otdDCPowerIndex
         INTEGER,
      otdDCPowerVoltage
         INTEGER,
      otdDCPowerCurrent
         INTEGER,
      otdDCPowerName
         DisplayString
   }

otdDCPowerIndex OBJECT-TYPE
   SYNTAX INTEGER 
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"直流电源索引。"
   ::={ otdDCPowerEntry 1 }

otdDCPowerVoltage OBJECT-TYPE
   SYNTAX INTEGER (-32768..32767)
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"电源电压，单位为0.1V。此对象要求在属性MIB中登记一个条目。"
   ::={ otdDCPowerEntry 2 }

otdDCPowerCurrent OBJECT-TYPE
   SYNTAX INTEGER (0..65535)
   ACCESS read-only
   STATUS optional
   DESCRIPTION
"电源电流，单位为0.1A。此对象要求在属性MIB中登记一个条目。"
   ::={ otdDCPowerEntry 3 }

otdDCPowerName OBJECT-TYPE
   SYNTAX DisplayString
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
"标明电源的名称，例如：24V直流电源。
此字段值由用户规定，至少应标明工作电压并将多个电源相互区分开。
当表中的对象产生告警时，此对象名称应放进hfcAlarmEvent陷阱的alarmText对象里（见
附录D）。"
   ::={ otdDCPowerEntry 4 }


END
💿 文件大小 26 K
👤 上传用户 cocoplus
📂 所属分类其他数据库
🏷️ 相关标签

#HFC #MIB #网管系统 #设备
⌨️ 快捷键说明

复制代码 Ctrl + C
搜索代码 Ctrl + F
全屏模式 F11
切换主题 Ctrl + Shift + D
显示快捷键 ?
增大字号 Ctrl + =
减小字号 Ctrl + -