scsipassthruext.h

来自「EFI BIOS是Intel提出的下一代的BIOS标准。这里上传的Edk源代码是」· C头文件 代码 · 共 366 行 · 第 1/2 页

/*++

  Copyright (c) 2006, Intel Corporation                                                         
  All rights reserved. This program and the accompanying materials                          
  are licensed and made available under the terms and conditions of the BSD License         
  which accompanies this distribution.  The full text of the license may be found at        
  http://opensource.org/licenses/bsd-license.php                                            

  THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,                     
  WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.             

Module Name:

    ScsiPassThruExt.h
    
Abstract: 
  EFI_EXT_SCSI_PASS_THRU_PROTOCOL as defined in UEFI 2.0.

Revision History

--*/

#ifndef __EXT_SCSI_PASS_THROUGH_PROTOCOL_H__
#define __EXT_SCSI_PASS_THROUGH_PROTOCOL_H__

#define EFI_EXT_SCSI_PASS_THRU_PROTOCOL_GUID \
  { \
    0x1d3de7f0, 0x0807, 0x424f, {0xaa, 0x69, 0x11, 0xa5, 0x4e, 0x19, 0xa4, 0x6f } \
  }

typedef struct _EFI_EXT_SCSI_PASS_THRU_PROTOCOL EFI_EXT_SCSI_PASS_THRU_PROTOCOL;

#define TARGET_MAX_BYTES                             0x10

#define EFI_EXT_SCSI_PASS_THRU_ATTRIBUTES_PHYSICAL   0x0001
#define EFI_EXT_SCSI_PASS_THRU_ATTRIBUTES_LOGICAL    0x0002
#define EFI_EXT_SCSI_PASS_THRU_ATTRIBUTES_NONBLOCKIO 0x0004

//
// DataDirection
//
#define EFI_EXT_SCSI_DATA_DIRECTION_READ             0
#define EFI_EXT_SCSI_DATA_DIRECTION_WRITE            1
#define EFI_EXT_SCSI_DATA_DIRECTION_BIDIRECTIONAL    2
//
// HostAdapterStatus
//
#define EFI_EXT_SCSI_STATUS_HOST_ADAPTER_OK                    0x00
#define EFI_EXT_SCSI_STATUS_HOST_ADAPTER_TIMEOUT_COMMAND       0x09
#define EFI_EXT_SCSI_STATUS_HOST_ADAPTER_TIMEOUT               0x0b
#define EFI_EXT_SCSI_STATUS_HOST_ADAPTER_MESSAGE_REJECT        0x0d
#define EFI_EXT_SCSI_STATUS_HOST_ADAPTER_BUS_RESET             0x0e
#define EFI_EXT_SCSI_STATUS_HOST_ADAPTER_PARITY_ERROR          0x0f
#define EFI_EXT_SCSI_STATUS_HOST_ADAPTER_REQUEST_SENSE_FAILED  0x10
#define EFI_EXT_SCSI_STATUS_HOST_ADAPTER_SELECTION_TIMEOUT     0x11
#define EFI_EXT_SCSI_STATUS_HOST_ADAPTER_DATA_OVERRUN_UNDERRUN 0x12
#define EFI_EXT_SCSI_STATUS_HOST_ADAPTER_BUS_FREE              0x13
#define EFI_EXT_SCSI_STATUS_HOST_ADAPTER_PHASE_ERROR           0x14
#define EFI_EXT_SCSI_STATUS_HOST_ADAPTER_OTHER                 0x7f
//
// TargetStatus
//
#define EFI_EXT_SCSI_STATUS_TARGET_GOOD                        0x00
#define EFI_EXT_SCSI_STATUS_TARGET_CHECK_CONDITION             0x02
#define EFI_EXT_SCSI_STATUS_TARGET_CONDITION_MET               0x04
#define EFI_EXT_SCSI_STATUS_TARGET_BUSY                        0x08
#define EFI_EXT_SCSI_STATUS_TARGET_INTERMEDIATE                0x10
#define EFI_EXT_SCSI_STATUS_TARGET_INTERMEDIATE_CONDITION_MET  0x14
#define EFI_EXT_SCSI_STATUS_TARGET_RESERVATION_CONFLICT        0x18
#define EFI_EXT_SCSI_STATUS_TARGET_TASK_SET_FULL               0x28
#define EFI_EXT_SCSI_STATUS_TARGET_ACA_ACTIVE                  0x30
#define EFI_EXT_SCSI_STATUS_TARGET_TASK_ABORTED                0x40

typedef struct {
  UINT32 AdapterId;
  UINT32 Attributes;
  UINT32 IoAlign;
} EFI_EXT_SCSI_PASS_THRU_MODE;

typedef struct {
  UINT64 Timeout;
  VOID   *InDataBuffer;
  VOID   *OutDataBuffer;
  VOID   *SenseData;
  VOID   *Cdb;
  UINT32 InTransferLength;
  UINT32 OutTransferLength;
  UINT8  CdbLength;
  UINT8  DataDirection;
  UINT8  HostAdapterStatus;
  UINT8  TargetStatus;
  UINT8  SenseDataLength;
} EFI_EXT_SCSI_PASS_THRU_SCSI_REQUEST_PACKET;

typedef
EFI_STATUS
(EFIAPI *EFI_EXT_SCSI_PASS_THRU_PASSTHRU) (
  IN EFI_EXT_SCSI_PASS_THRU_PROTOCOL                *This,
  IN UINT8                                          *Target,
  IN UINT64                                         Lun,
  IN OUT EFI_EXT_SCSI_PASS_THRU_SCSI_REQUEST_PACKET *Packet,
  IN EFI_EVENT                                      Event     OPTIONAL
  )
/*++

  Routine Description:
    Sends a SCSI Request Packet to a SCSI device that is attached to the SCSI channel. This function   
    supports both blocking I/O and nonblocking I/O. The blocking I/O functionality is required, and the
    nonblocking I/O functionality is optional.                                                             
  
  Arguments:
    This   - A pointer to the EFI_EXT_SCSI_PASS_THRU_PROTOCOL instance.
    Target - The Target is an array of size TARGET_MAX_BYTES and it represents
             the id of the SCSI device to send the SCSI Request Packet. Each
             transport driver may chose to utilize a subset of this size to suit the needs
             of transport target representation. For example, a Fibre Channel driver
             may use only 8 bytes (WWN) to represent an FC target.
    Lun    - The LUN of the SCSI device to send the SCSI Request Packet.
    Packet - A pointer to the SCSI Request Packet to send to the SCSI device
             specified by Target and Lun.
    Event  - If nonblocking I/O is not supported then Event is ignored, and blocking
             I/O is performed. If Event is NULL, then blocking I/O is performed. If
             Event is not NULL and non blocking I/O is supported, then
             nonblocking I/O is performed, and Event will be signaled when the
             SCSI Request Packet completes.

  Returns:
    EFI_SUCCESS          - The SCSI Request Packet was sent by the host. For bi-directional
                           commands, InTransferLength bytes were transferred from
                           InDataBuffer. For write and bi-directional commands,
                           OutTransferLength bytes were transferred by
                           OutDataBuffer.
    EFI_BAD_BUFFER_SIZE  - The SCSI Request Packet was not executed. The number of bytes that
                           could be transferred is returned in InTransferLength. For write
                           and bi-directional commands, OutTransferLength bytes were
                           transferred by OutDataBuffer.
    EFI_NOT_READY        - The SCSI Request Packet could not be sent because there are too many
                           SCSI Request Packets already queued. The caller may retry again later.
    EFI_DEVICE_ERROR     - A device error occurred while attempting to send the SCSI Request
                           Packet.
    EFI_INVALID_PARAMETER- Target, Lun, or the contents of ScsiRequestPacket are invalid.
    EFI_UNSUPPORTED      - The command described by the SCSI Request Packet is not supported
                           by the host adapter. This includes the case of Bi-directional SCSI
                           commands not supported by the implementation. The SCSI Request
                           Packet was not sent, so no additional status information is available.
    EFI_TIMEOUT          - A timeout occurred while waiting for the SCSI Request Packet to execute.

--*/
;      

typedef
EFI_STATUS
(EFIAPI *EFI_EXT_SCSI_PASS_THRU_GET_NEXT_TARGET_LUN) (
  IN EFI_EXT_SCSI_PASS_THRU_PROTOCOL                *This,
  IN OUT UINT8                                      **Target,
  IN OUT UINT64                                     *Lun
  )
/*++
  Routine Description:
    Used to retrieve the list of legal Target IDs and LUNs for SCSI devices on a SCSI channel. These       
    can either be the list SCSI devices that are actually present on the SCSI channel, or the list of legal
    Target Ids and LUNs for the SCSI channel. Regardless, the caller of this function must probe the       
    Target ID and LUN returned to see if a SCSI device is actually present at that location on the SCSI    
    channel.                                                                                               
  
  Arguments:
    This    - A pointer to the EFI_EXT_SCSI_PASS_THRU_PROTOCOL instance
    Target  - On input, a pointer to the Target ID (an array of size
              TARGET_MAX_BYTES) of a SCSI device present on the SCSI channel.
              On output, a pointer to the Target ID (an array of
              TARGET_MAX_BYTES) of the next SCSI device present on a SCSI
              channel. An input value of 0xF(all bytes in the array are 0xF) in the
              Target array retrieves the Target ID of the first SCSI device present on
              a SCSI channel.
    Lun     - On input, a pointer to the LUN of a SCSI device present on the SCSI
              channel. On output, a pointer to the LUN of the next SCSI device present
              on a SCSI channel.
  
  Returns:
    EFI_SUCCESS           - The Target ID and LUN of the next SCSI device on the SCSI
                            channel was returned in Target and Lun.
    EFI_INVALID_PARAMETER - Target array is not all 0xF, and Target and Lun were
                            not returned on a previous call to GetNextTargetLun().