igetstrt1a.htm

mips架构的bootloader,99左右的版本 但源代码现在没人更新了

		<title>Getting Started with SerialICE-1A</title>
		<h1 align=center>Getting Started with SerialICE-1A</h1>

<!--INDEX "PMON Web Site" "SerialICE Controller Selection"  -->
<!--INDEX "Getting Started with SerialICE-1A" -->
<!--INDEX "SerialICE Controller types" "Target types" -->

<!-- Note: The ATMizer2 is not currently supported. It needs a kernel. -->

<center><table><tr>
<th> What You'll Need</th></tr>
<tr><td><ul>
	<li>A Host computer system (UNIX or <a href="dosdef.htm">MSDOS</a>)
	<li>An <a href="ctypes.htm">SerialICE Controller</a> board
	<li>A <a href="ttypes.htm">Target</a> board
</ul></table></center>

To run an application program on your Target using SerialICE-1A, perform the
following steps:<p>

<ol>
<li>If you haven't done so already, 
<a href="http://www.carmel.com/pmon">Download</a> 
the PMON source from the Web site.

<li>Next you need to <a href="xtrfiles.htm">Extract</a> the files 
from the archive.<p>

<!--
You might need to extract more than one copy of the
PMON sources, it depends on the combination of SerialICE Controller and Target
you are planning to use. See below,<p>
-->

<dl><dd>
<table border cellpadding=6>
<tr><th></th><th colspan=2>SerialICE Controller</th></tr>
<tr><th>Target</th><th>BDMR4101-be</th><th>BDMR4101-le</th></tr>
<tr><td><a href="bdmr4101.htm">BDMR4101-be</a></td><td>all-be</td><td>all-be-le</td></tr>
<tr><td><a href="bdmr4011.htm">BDMR4011-be</a></td><td>all-be</td><td>all-be-le</td></tr>
<tr><td><a href="bdmr4102.htm">BDMR4102-be</a></td><td>all-be</td><td>all-be-le</td></tr>

<tr><td><a href="bdmr4101.htm">BDMR4101-le</a></td><td>all-be-le</td><td>all-le</td></tr>
<tr><td><a href="bdmr4011.htm">BDMR4011-le</a></td><td>all-be-le</td><td>all-le</td></tr>
<tr><td><a href="bdmr4102.htm">BDMR4102-le</a></td><td>all-be-le</td><td>all-le</td></tr>
<!--
<tr><td>BDMR4001-be</td><td>all-be</td><td>all-be-le</td></tr>
<tr><td>BDMR4003-be</td><td>all-be</td><td>all-be-le</td></tr>
<tr><td>BDMR4001-le</td><td>all-be-le</td><td>all-le</td></tr>
<tr><td>BDMR4003-le</td><td>all-be-le</td><td>all-le</td></tr>
<tr><td>L64008</td><td>all-be<br>sdp1000</td><td>all-le<br>sdp1000</td></tr>
<tr><td>L64363 (ATMizer2)</td><td>all-be<br>l64363</td><td>all-le<br>l64363</td></tr>
-->
<tr><td colspan=3> Key: The "-be" means Big Endian, the "-le" means Little Endian.</td></tr>
</table><p>
</dl>


<!--
If the combination you are planning to use shows a single name eg.
all-be or all-be-le, you need only unpack one copy of the PMON sources.
If, on the other hand, the combination have chosen shows two names eg.
all-be <i>and</i> sdp1000, you will need to unpack two separate copies
of the PMON sources, each in it's own directory.<p>
-->

<li>To configure the package you need to run the <a
href="pinstall.htm">Install</a> program using the information that you
obtained from the body of the table above.<p>

For example, if your
selection shows "all-be", then you need to specify target type 1
during the installation (All Big Endian Processors), if "all-le" then
select target type 2 (All Little Endian Processors), if it shows
"all-be-le" then select target type 1 (All Big Endian Processors), but
when the install program presents you with a summary of all the
selected options, select the "Endian Support" option and enter "1 2"
to select both byte orderings. Do not change the "Default Endian".<p>

<!--
If you unpacked two copies of the PMON sources,
you will need to run the Install program in each of the two directories,
one with each of
the two target types. 
-->
The target type information is summarized below.<p>

<dl><dd><table border cellpadding=6>
<tr><th>Target Type</th><th>Target Name</th></tr>
<tr><td>all-be</td><td>"All Processors Big Endian"</td></tr>
<tr><td>all-le</td><td>"All Processors Little Endian"</td></tr>
<tr><td>all-be-le</td><td>"All Processors Big Endian" and<br>Change "Endian Support" to "1 2"</td></tr>
<!--
<tr><td>all-le-be</td><td>"All Processors Little Endian" and<br>Change "Endian Support" to "1 2"</td></tr>
<tr><td>nitro</td><td>"4011 Nitro II"</td></tr>
<tr><td>sdp1000</td><td>"SDP1000 (L64008 MPEG-2 Transport)"</td></tr>
<tr><td>l64363</td><td>"ATMizer-2 R-T SAR Engine"</td></tr>
-->
</table><p></dl>

<li>To prepare the package for use you must 
<a href="ibuild1a.htm">Build</a> the package.

<li>Configure your hardware.<p>
SerialICE requires an RS232 link between your host and port A on the
SerialICE Controller, and a null-modem RS232 link between port B on the
SerialICE Controller and port A on your Target. The 
<a href="portname.htm">actual hardware port names</a>
will depend on which host, SerialICE Controller, and Target you will be
using.<p>

<li><a href="idinst.htm">Install</a> the driver.

<li><a href="iabuild.htm">Build</a>, 
<a href="dlexe.htm">Download and Execute</a> your application on the Target.

</ol>


</dl><p><hr>
<b>Navigation:</b> 
<a href="index.htm">Document Home</a> | 
<a href="doctoc.htm">Document Contents</a> | 
<a href="docindex.htm">Document Index</a> <p>