📄 readme.txt
字号:
The README.TXT file contains:
I. Current release version for drivers and utilities.
II. Device drivers and utilities usage of PCMCIA/CitiROM.
III. Product support list( Not all inclusive )
IV. Technical tips
All of the device drivers and utilities are fully compatible with
PCMCIA/CitiROM card. Please use this file as supplement to your
installation/user guide.
I. Current released device drivers and utilities version.
******************************************************
PCMIDE sub-directory--
PCMI80CL SYS 4,222 07-13-99 9:04p v5.80
STATPCDM SYS 17,945 11-09-98 9:02p v2.70
STATPFLP SYS 18,208 12-07-98 10:52p v5.20
STIDEHDD SYS 17,694 10-27-00 7:56p v5.60
README EXE 38261 03-23-94 3:53p
README TXT
II. Device Driver and Utility Usage of PCMCIA/CitiROM card
==============================================
PCMI80CL.SYS ( ATAPI/IDE PCMCIA Client Driver )
==============================================
This driver supports the PCMCIA 2.1+ Card/Socket services
specifications. It is mandatory to load this driver
before using the STATPCDM.SYS device driver. This device
driver is PCMCIA/CitiROM card specific. This driver support
both PMIDE-M17 and PMIDE-ASC type cards' I/O addressing
technique.
Adding in the enabling functions from release v5.0. If no
Card/Socket services is installed, the client service will then
turn on the socket based on the following syntax.
Installation Format:
Device = <path>\PCMI80CL.SYS [/Xn]
/Xn - Ignore the checking the card service version
1 -- ignore, 0 -- check( default )
/Pn - Set the enabler I/O port.
0 - 150( default ), 1 -160, 2 - 170.
/Qn - Set the enabler IRQ selection.
0 to 9 or A to F. A=10. F=15.
/Vn - Special value for VIA PCMICA controller
0 ( default ), 1 -- set via mode
==============================================
STATPCDM.SYS( ATAPI/IDE CD-ROM device driver )
==============================================
This device driver requires the PCMI80CL.SYS client driver.
Install the PCMI80CL.SYS driver before the STATPCDM.SYS driver.
Installation Format:
Device = <path>\STATPCDM.SYS [/I:n] [/Qn] /D:<drive name>
/I:n - how many drive letter to be reserved for plug
and play purpose, when using this parameter
the CD-ROM drives will not be initialized when
system bootup. However, be sure the card is
inserted in the system boot up time to allow
Card/Socket/Client services to recognize the
existence.
n must be 1 - 2
Default value is 1 if n is not specified.
/Qn - Use Interrupt
1 -- yes( default ), 0 -- no, use polling
/D:<drive name> - specified the drive name for
MSCDEX to match
Defautl name is SCSIDE0
/T - Set Torishan24X CD-ROM mode.
Please install MSCDEX.EXE in AUTOEXEC.BAT file as shown below:
MSCDEX /D:<drive name> /M:10
==============================================================
STIDEHDD.SYS( IDE Fixed or Removable Hard Disk device driver )
==============================================================
This device driver requires the PCMI80CL.SYS client driver.
Install the PCMI80CL.SYS driver before the STIDEHDD.SYS driver.
Adding in the FAT32 file system support for DOS7.0( Win95
Rev. B or OSR2 command prompt mode ) and still retain the
backward compatibility with FAT16 and FAT12 as well.
Installation Format:
Device = <path>\STIDEHDD.SYS
For disk( diskette ) preparation, please use the DOS supported
FDISK and FORMAT utilities.
For removable cartridge drive like Fujitsui IDE/MO and SyQuest
SyJet drive, FDISK is not available. Only large floppy format
supported.
==============================================================
STATPFLP.SYS( IDE/ATAPI Removable Hard Disk device driver, LS120 )
==============================================================
This device driver requires the PCMI80CL.SYS client driver.
Support LS120 Floppy Drive.
Install the PCMI80CL.SYS driver before the STATPFLP.SYS driver.
Installation Format:
Device = <path>\STATPFLP.SYS
For diskette preparation, please use the DOS supported
FORMAT utilities. No partition capability supported.
III. Product Support List - Not all inclusive
********************
Most IDE or Enhanced IDE ATAPI CD-ROM/Floppy devices are supported even
they may not be listed above. New models are constantly added to
to the list. Please consult the dealers for updated information.
The adapter has been tested under the following environments.
All the above supported softwares are for IBM PC AT or compatibles.
IDE Devices:
.ATAPI/IDE CD-ROM
Manufacturer Model No.
--------------------------------------
Acer 744, 747 4X, 6X, 8X
Funai 6X, 8X
IMES 6X, 8X
Goldstar GCD-520, 540, 6X, 8X
Laser Magnetic CM207
Lasonic CDM-100S
MediaVision 6X
Mitsumi FX-00IDE, 4x, 8x, 12x
NEC CDR-250, 260, MultiSpin 2Vi, 4X
Optical Storage 8001IDE
Part II Research SpaceShip
Panasonic CD-571, MC-579,
UJDA110, UJDA121 20X slim
Reveal 4x
SONY CDU-55D, 55E, 76E, 8X
TEAC 6X, 8X slimline, CD211E 20X slim
Toshiba XM-5202, 5302, 4x, 6X, 8X, 1602B slim
ToriSan 20X slim
Wearnes CDD-120
.IDE Hard Disk Drive
Manufacturer Model No.
--------------------------------------
Conner 700MB, 2.5" 800MB
Hitachi 3.0GB
Fujitsu 2154 230MB Magneto-Optical drive
IBM 2.5" 540MB, 800MB, 2.0GB, 3.0GB, 6 GB
Maxtor 120MB, 100MB, 800MB, 1GB
Samsung 250MB
SyQuest 135 MB removable drive, 1.5GB
Seagate ST3295A,3660A, 1.0GB, 1.2GB
WesternDigital 2.5" 540MB
.IDE Floppy Drive
Manufacturer Model No.
--------------------------------------
Matsushita LS120
Mitsuibishi LS120, Slim LS120
IOMEGA Zip100, Slim Zip 100
Caleb Technology UHD 144
IV. Technical tips
**************
Use this section as supplement to the Trouble Shooting section in the
manual.
a. If your notebook or desktop PCMCIA card reader is using the
Databook controller, be sure to edit the SuperClient Driver
inside the CONFIG.SYS as the following:
"device=c:\pcmcia\cardtalk.sys /iow=150-157 /iow=350-357"
This will exclude the Cardtalk( SuperClient ) driver to
check the io range between the 150-157 and 350-357.
b. If your notebook or desktop PCMCIA card read is using the
CARDWARE services, be sure to edit the CARDWARE.INI [Resources]
section as the following:
I/O=0x150,0x10,E,10
I/O=0x350,0x10,E,10
IRQ=15,E
c. If your notebook or desktop PCMCIA card read is using the
Cirrus Logic Socket service, be sure to exclude the IRQ 15
as the resource for card service. Consult the PCMCIA driver
manual to exclude the resouce.
d. From Sept. 30, 1996, new version of CitiROM card( called PMIDE-ASC )
is released, it's required to upgrade all of the drivers to the
revision level above to function correctly. However, new drivers
will recognize and function exactly the same as the older version
if you mixing the PMIDE-M17 hardware and new drivers.
e. To use the LS120( 128 MB ) IDE Floppy Drive with CitiROM card,
please use the in-house designed driver to get the best
performance. Not all of the LS120 drive in the market support
the IDE Daisy-Chain function.
f. For FAT32 file support, please use the v3.1 STIDEHDD.SYS on DOS7.0
only( Win95 Rev. B, OSR2 ). Other DOS levels smaller than 7.0 will
not recognize the FAT32 file system and set them to "RESERVED"
partition. DOS7.0 will recognize the full HDD as one single Primary DOS
partition if size is smaller than 8GB.
g. New PCMI80CL.SYS v5.0 come with the enabler support. It will turn
on the socket controller if no Card/Socket services installed.
I/O port and IRQ selections are programmable via parameters setting.
The new client driver is applicable for STIDEHDD.SYS, STATPCDM.SYS
and STATPFLP.SYS as well.
h. STATPFLP.SYS v4.21 and greater support ZIP, slimline ZIP,
LS120, slimline LS120 and Caleb 144 UHD as well.
i. When using the PCMI80CL.SYS as enabler for VIA PCMCIA controller,
set "/V1" parameter so as to work properly.
h. FDISK/Format HDD larger than 8GB is supported from v5.26 and above of
"stidehdd.sys".
Technical supports:
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -