53772

神经网络昆斯林的新闻组分类2006

Newsgroups: sci.electronics
Path: cantaloupe.srv.cs.cmu.edu!magnesium.club.cc.cmu.edu!news.sei.cmu.edu!fs7.ece.cmu.edu!europa.eng.gtefsd.com!howland.reston.ans.net!spool.mu.edu!news.nd.edu!scarecrow.cse.nd.edu!jott
From: [e-mail] (John Ott)
Subject: Re: Pinout needed for TIL311
Message-ID: <[e-mail]>
Sender: [e-mail] (USENET News System)
Reply-To: [e-mail] (John Ott)
Organization: Univ. of Notre Dame
References:  <segal.734995860@corolla7>
Date: Mon, 19 Apr 1993 17:36:19 GMT
Lines: 64

In article <segal.734995860@corolla7>, [e-mail] (Gary Segal) writes:
|> I've recently picked up some TIL311 display chips, but I can't find
|> any information on them.  It seems they are no longer made by TI, and
|> I don't have an old enough data book.  :-(
|> 
|> It appears to have a dot-matrix led display capable of showing one hex
|> digit.  It is in a 14 pin DIP package, but pins 6, 9, and 11 are not
|> present.
|> 
|> If you have any information on this part (pinout, power requirments,
|> functions, ...) please send me e-mail.
|> 
|> Thank You,
|> 
|> -- 
|> Gary Segal                             Motorola Inc.            
|> [e-mail]               Cellular Infrastructure Division
|> 	--- we are standing here only to gaze at the wind ---


pin      function
 1      led supply voltage
 2      latch data input b
 3      latch data input a
 4      left decimal point cathode
 5      latch strobe input
 6      omitted
 7      common gnd
 8      blanking input
 9      omitted
10      right decimal point cathode
11      omitted
12      latch data input d
13      latch data input c
14      logic supply voltage (5v)

LATCH STROBE INPUT, pin 5, when low, the data in the latches follow the data on the latch data
                             inputs.  When high, the data in the latches will not change.  If the
                               display is blanked and then restored while the enable input is high,
                               the previous character will again be displayed.

BLANKING INPUT, pin 8,    When high, the display is blanked regardless of the levels of the other
                              inputs.  When low, a character is displayed as determined by the data
                              in the latches.  The blanking input may be pulsed for intensity modulation.

LATCH DATA INPUTS, pins 2,3,12,13,   Data on these inputs are entered into the latches when the enable
                                          input is low.  The binary weights of these inputs are A = 1,
                                          B = 2, C = 4, D = 8

DECIMAL POINT CATHODES, pins 4, 10,   These LEDS are not connected to the logic chip.  If a decimal point
                                          is used, an external resistor or other current limiting
                                          mechanism must be connected in series with it.

LED SUPPLY, pin 1            This connection permits the user to save on regulated Vcc current by using
                                 a separate LED supply, or it may be externally connected to the logic
                                 supply (Vcc).

LOGIC SUPPLY (Vcc), pin 14      Separate Vcc connection for the logic chip

COMMON GROUND, pin 7,      This is the vegative termnal for all logic and LED currents except for the
                              decimal points.

John
[e-mail]