rfc1242.txt

著名的RFC文档,其中有一些文档是已经翻译成中文的的.

Network Working Group                                 S. Bradner, Editor
Request for Comments: 1242                            Harvard University
                                                               July 1991


      Benchmarking Terminology for Network Interconnection Devices

Status of this Memo

   This memo provides information for the Internet community.  It does
   not specify an Internet standard.  Distribution of this memo is
   unlimited.

Abstract

   This memo discusses and defines a number of terms that are used in
   describing performance benchmarking tests and the results of such
   tests.  The terms defined in this memo will be used in additional
   memos to define specific benchmarking tests and the suggested format
   to be used in reporting the results of each of the tests.  This memo
   is a product of the Benchmarking Methodology Working Group (BMWG) of
   the Internet Engineering Task Force (IETF).

1.  Introduction

   Vendors often engage in "specsmanship" in an attempt to give their
   products a better position in the marketplace.  This usually involves
   much "smoke & mirrors" used to confuse the user.  This memo and
   follow-up memos attempt to define a specific set of terminology and
   tests that vendors can use to measure and report the performance
   characteristics of network devices.  This will provide the user
   comparable data from different vendors with which to evaluate these
   devices.

2.  Definition format

        Term to be defined. (e.g., Latency)

        Definition:
                The specific definition for the term.

        Discussion:
                A brief discussion about the term, it's application
                and any restrictions on measurement procedures.

        Measurement units:
                The units used to report measurements of this
                term, if applicable.



Benchmarking Methodology Working Group                          [Page 1]

RFC 1242                Benchmarking Terminology               July 1991


        Issues:
                List of issues or conditions that effect this term.

        See Also:
                List of other terms that are relevant to the discussion
                of this term.

3.  Term definitions

3.1  Back-to-back

        Definition:
                Fixed length frames presented at a rate such that there
                is the minimum legal separation for a given medium
                between frames over a short to medium period of time,
                starting from an idle state.

        Discussion:
                A growing number of devices on a network can produce
                bursts of back-to-back frames.  Remote disk servers
                using protocols like NFS, remote disk backup systems
                like rdump, and remote tape access systems can be
                configured such that a single request can result in
                a block of data being returned of as much as 64K octets.
                Over networks like ethernet with a relatively small MTU
                this results in many fragments to be transmitted.  Since
                fragment reassembly will only be attempted if all
                fragments have been received, the loss of even one
                fragment because of the failure of some intermediate
                network device to process enough continuous frames can
                cause an endless loop as the sender repetitively
                attempts to send its large data block.

                With the increasing size of the Internet, routing
                updates can span many frames, with modern routers able
                to transmit very quickly.  Missing frames of routing
                information can produce false indications of
                unreachability.  Tests of this parameter are intended
                to determine the extent of data buffering in the
                device.

        Measurement units:
                Number of N-octet frames in burst.

        Issues:

        See Also:




Benchmarking Methodology Working Group                          [Page 2]

RFC 1242                Benchmarking Terminology               July 1991


3.2  Bridge

        Definition:
                A system which forwards data frames based on information
                in the data link layer.

        Discussion:

        Measurement units:
                n/a

        Issues:

        See Also:
                bridge/router (3.3)
                router (3.15)

3.3  bridge/router

        Definition:
                A bridge/router is a network device that can selectively
                function as a router and/or a bridge based on the
                protocol of a specific frame.

        Discussion:

        Measurement units:
                n/a

        Issues:

        See Also:
                bridge (3.2)
                router (3.15)

3.4  Constant Load

        Definition:
                Fixed length frames at a fixed interval time.

        Discussion:
                Although it is rare, to say the least, to encounter
                a steady state load on a network device in the real
                world, measurement of steady state performance may
                be useful in evaluating competing devices.  The
                frame size is specified and constant.  All device
                parameters are constant.  When there is a checksum
                in the frame, it must be verified.



Benchmarking Methodology Working Group                          [Page 3]

RFC 1242                Benchmarking Terminology               July 1991


        Measurement units:
                n/a

        Issues:
                unidirectional vs. bidirectional

        See Also:

3.5  Data link frame size

        Definition:
                The number of octets in the frame from the first octet
                following the preamble to the end of the FCS, if
                present, or to the last octet of the data if there
                is no FCS.

        Discussion:
                There is much confusion in reporting the frame
                sizes used in testing network devices or network
                measurement.  Some authors include the checksum,
                some do not.  This is a specific definition for use
                in this and subsequent memos.

        Measurement units:
                octets

        Issues:

        See Also:

3.6  Frame Loss Rate

        Definition:
                Percentage of frames that should have been forwarded
                by a network device under steady state (constant)
                load that were not forwarded due to lack of
                resources.

        Discussion:
                This measurement can be used in reporting the
                performance of a network device in an overloaded
                state.  This can be a useful indication of how a
                device would perform under pathological network
                conditions such as broadcast storms.

        Measurement units:
                Percentage of N-octet offered frames that are dropped.
                To be reported as a graph of offered load vs frame loss.



Benchmarking Methodology Working Group                          [Page 4]

RFC 1242                Benchmarking Terminology               July 1991


        Issues:

        See Also:
                overhead behavior (3.11)
                policy based filtering (3.13)
                MTU mismatch behavior (3.10)

3.7  Inter Frame Gap

        Definition:
                The delay from the end of a data link frame as defined
                in section 3.5, to the start of the preamble of the
                next data link frame.

        Discussion:
                There is much confusion in reporting the between
                frame time used in testing network devices.  This
                is a specific definition for use in this and subsequent
                memos.

        Measurement units:
                Time with fine enough units to distinguish between
                2 events.

        Issues:
                Link data rate.

        See Also:

3.8   Latency

        Definition:
                For store and forward devices:
                The time interval starting when the last bit of the
                input frame reaches the input port and ending when
                the first bit of the output frame is seen on the
                output port.

                For bit forwarding devices:
                The time interval starting when the end of the first
                bit of the input frame reaches the input port and
                ending when the start of the first bit of the output
                frame is seen on the output port.

        Discussion:
                Variability of latency can be a problem.
                Some protocols are timing dependent (e.g., LAT and IPX).
                Future applications are likely to be sensitive to



Benchmarking Methodology Working Group                          [Page 5]

RFC 1242                Benchmarking Terminology               July 1991


                network latency.  Increased device delay can reduce
                the useful diameter of net.  It is desired to
                eliminate the effect of the data rate on the latency
                measurement.  This measurement should only reflect the
                actual within device latency.  Measurements should be
                taken for a spectrum of frame sizes without changing
                the device setup.

                Ideally, the measurements for all devices would be from
                the first actual bit of the frame after the preamble.
                Theoretically a vendor could design a device that
                normally would be considered a store and forward
                device, a bridge for example, that begins transmitting
                a frame before it is fully received.  This type of
                device is known as a "cut through" device.  The
                assumption is that the device would somehow invalidate
                the partially transmitted frame if in receiving the
                remainder of the input frame, something came up that
                the frame or this specific forwarding of it was in
                error.  For example, a bad checksum.  In this case,
                the device would still be considered a store and
                forward device and the latency would still be
                from last bit in to first bit out, even though the
                value would be negative.  The intent is to treat
                the device as a unit without regard to the internal
                structure.

        Measurement units:
                Time with fine enough units to distinguish between
                2 events.

        Issues:

        See Also:
                link speed mismatch (3.9)
                constant load (3.4)
                back-to-back (3.1)
                policy based filtering (3.13)
                single frame behavior (3.16)

3.9  Link Speed Mismatch

        Definition:
                Speed mismatch between input and output data rates.

        Discussion:
                This does not refer to frame rate per se, it refers to
                the actual data rate of the data path.  For example,



Benchmarking Methodology Working Group                          [Page 6]