eth_spram_256x32.v

人民邮电出版社出版的《FPGA硬件接口设计实践》一书的代码

`include "eth_defines.v"
`include "timescale.v"

module eth_spram_256x32(
	// Generic synchronous single-port RAM interface
	clk, rst, ce, we, oe, addr, di, do

`ifdef ETH_BIST
  ,
  // debug chain signals
  scanb_rst,      // bist scan reset
  scanb_clk,      // bist scan clock
  scanb_si,       // bist scan serial in
  scanb_so,       // bist scan serial out
  scanb_en        // bist scan shift enable
`endif



);

	//
	// Generic synchronous single-port RAM interface
	//
	input           clk;  // Clock, rising edge
	input           rst;  // Reset, active high
	input           ce;   // Chip enable input, active high
	input           we;   // Write enable input, active high
	input           oe;   // Output enable input, active high
	input  [7:0]    addr; // address bus inputs
	input  [31:0]   di;   // input data bus
	output [31:0]   do;   // output data bus


`ifdef ETH_BIST
  input   scanb_rst;      // bist scan reset
  input   scanb_clk;      // bist scan clock
  input   scanb_si;       // bist scan serial in
  output  scanb_so;       // bist scan serial out
  input   scanb_en;       // bist scan shift enable
`endif

`ifdef ETH_XILINX_RAMB4

    RAMB4_S16 ram0
    (
        .DO      (do[15:0]),
        .ADDR    (addr),
        .DI      (di[15:0]),
        .EN      (ce),
        .CLK     (clk),
        .WE      (we),
        .RST     (rst)
    );

    RAMB4_S16 ram1
    (
        .DO      (do[31:16]),
        .ADDR    (addr),
        .DI      (di[31:16]),
        .EN      (ce),
        .CLK     (clk),
        .WE      (we),
        .RST     (rst)
    );

`else   // !ETH_XILINX_RAMB4
`ifdef  ETH_VIRTUAL_SILICON_RAM
  `ifdef ETH_BIST
      vs_hdsp_256x32_bist ram0_bist
  `else
      vs_hdsp_256x32 ram0
  `endif
      (
        .CK         (clk),
        .CEN        (!ce),
        .WEN        (!we),
        .OEN        (!oe),
        .ADR        (addr),
        .DI         (di),
        .DOUT       (do)

      `ifdef ETH_BIST
        ,
        // debug chain signals
        .scanb_rst      (scanb_rst),
        .scanb_clk      (scanb_clk),
        .scanb_si       (scanb_si),
        .scanb_so       (scanb_so),
        .scanb_en       (scanb_en)
      `endif
      );

`else   // !ETH_VIRTUAL_SILICON_RAM

	//
	// Generic single-port synchronous RAM model
	//

	//
	// Generic RAM's registers and wires
	//
	reg  [31:0] mem [255:0];	// RAM content
	wire [31:0] q;          // RAM output
	reg  [7:0]  raddr;      // RAM read address
	//
	// Data output drivers
	//
	assign do = (oe & ce) ? q : {32{1'bz}};

	//
	// RAM read and write
	//

	// read operation
	always@(posedge clk)
	if (ce) // && !we)
		raddr <= #1 addr;    // read address needs to be registered to read clock

	assign #1 q = rst ? {32{1'b0}} : mem[raddr];

	// write operation
	always@(posedge clk)
		if (ce && we)
			mem[addr] <= #1 di;

	// Task prints range of memory
	// *** Remember that tasks are non reentrant, don't call this task in parallel for multiple instantiations. 
	task print_ram;
	input [7:0] start;
	input [7:0] finish;
	integer rnum;
  	begin
    		for (rnum=start;rnum<=finish;rnum=rnum+1)
      			$display("Addr %h = %h",rnum,mem[rnum]);
  	end
	endtask

`endif  // !ETH_VIRTUAL_SILICON_RAM
`endif  // !ETH_XILINX_RAMB4

endmodule