halsrf04.h

CC1100的示例程序

 
    
//------------------------------------------------------------------------------------------------------
//  SETUP_GDO2_INT(trigger, polarity)
//
//  DESCRIPTION:
//      This macro is setting up the GDO2 interrupt from CCxx00. The interrupt is on P0.7 and is 
//      assign to external interrupt1. The macro enables external interrupt1.
//
//  ARGUMENTS:
//      trigger
//          EDGE    (interrupt is edge sensitive)
//          LEVEL   (interrupt is level sensitive)
//      polarity
//          HIGH    (input is active high)
//          LOW     (input is active low)
//------------------------------------------------------------------------------------------------------
#define SETUP_GDO2_INT(trigger, polarity) \
    do { \
        IT1 = trigger; \
        IT01CF = ((IT01CF & 0x0F) | ((polarity << 7) | 0x70)); \
        INT_ENABLE(INUM_EXTERNAL1, INT_ON); \
    } while (0)
//------------------------------------------------------------------------------------------------------

// where trigger is one of:
#define LEVEL   0
#define EDGE    1

// where polarity is one of:
#define LOW     0
#define HIGH    1
//------------------------------------------------------------------------------------------------------





/*******************************************************************************************************
 *******************************************************************************************************
 **************************                 UART SERIAL PORT                 ***************************
 *******************************************************************************************************
 *******************************************************************************************************/
//-------------------------------------------------------------------------------------------------------
// This section contains useful macros for configuring the UART and for TX and RX using the UART
//      UART_SETUP(baudRate, options)
//      UART_TX_ENABLE()
//      UART_RX_ENABLE()
//      UART_TX_WAIT()
//      UART_RX_WAIT()
//      UART_TX(x)
//      UART_RX(x)
//      UART_WAIT_AND_SEND(x)
//      UART_WAIT_AND_RECEIVE(x)
//-------------------------------------------------------------------------------------------------------




//-------------------------------------------------------------------------------------------------------
// Options for UART configuration
#define DEFAULT_MODE        0x00    // 8-bit Uart with variable baudrate, logic level of stop bit is 
                                    // ignored. User must poll the RI_0 and TI_0 flag to determine when a 
                                    // byte arrives or when the TX buffer is empty. The user must manually
                                    // clear RI0 and TI0 if not using the printf() / scanf() functions 
                                    // which do this automatically. 
#define UART_ISR            0x01    // Use interrupt service routines to signal that a byte has arrived or
                                    // that the TX buffer is empty. The user must manually clear RI_0 and
                                    // TI_0 in the corresponding ISRs.
//-------------------------------------------------------------------------------------------------------

                                   


//-------------------------------------------------------------------------------------------------------
// Defines used for the _baudrate_ variable
#define UART_BAUDRATE_4800      0
#define UART_BAUDRATE_9600      1            
#define UART_BAUDRATE_19200     2
#define UART_BAUDRATE_38400     3
#define UART_BAUDRATE_57600     4
#define UART_BAUDRATE_115200    5
//-------------------------------------------------------------------------------------------------------

 


//------------------------------------------------------------------------------------------------------
//  void halUartSetup(UINT16 baudRate, UINT8 options)
//
//  DESCRIPTION:
//      Function which implements all the initialization necessary to establish a simple serial link. 
//      Timer1 is used as a baudrate generator and is initialized according to _baudRate_. Timer 1 
//      is enabled and configures for Mode 2; 8-bit counter/timer with auto-reload. The UART 
//      is configured according to _options_.
//      The system clock needs to be configured to run at 24 MHz. 
//
//  ARGUMENTS:
//      UINT16 baudRate
//          UART_BAUDRATE_4800
//          UART_BAUDRATE_9600
//          UART_BAUDRATE_19200
//          UART_BAUDRATE_38400
//          UART_BAUDRATE_57600
//          UART_BAUDRATE_115200
//      UINT16 clkFreq
//          Device clock frequency in kHz
//      UINT8 options
//          DEFAULT_MODE           
//          UART_ISR
//------------------------------------------------------------------------------------------------------
void halUartSetup(UINT8 baudRate, UINT8 options);




//-------------------------------------------------------------------------------------------------------
// Macros which are helpful when transmitting and receiving data over the serial interface.
//
// Example of usage:
//
//      UART_TX_ENABLE();
//      UART_TX(data);
//
//      for (i = 1; i < len; i++) {
//          UART_WAIT_AND_SEND(pData[i]);
//      }
//
//      UART_RX_ENABLE();
//      len = UART_RX();
//
//      while (len-- > 0) {
//          UART_WAIT_AND_RECEIVE(data[i++]);
//      }

#define UART_TX_ENABLE()            do { REN0 = 0; } while (0)
#define UART_RX_ENABLE()            do { REN0 = 1; } while (0)

#define UART_TX_WAIT()              do {while (!INT_GETFLAG(INUM_UART0_TX)); } while (0)
#define UART_RX_WAIT()              do {while (!INT_GETFLAG(INUM_UART0_RX)); } while (0) 

#define UART_TX(x)                  do { SBUF0 = (x); } while (0)
#define UART_RX(x)                  do { (x) = SBUF0; } while (0)

#define UART_WAIT_AND_SEND(x) \
    do { \
        UART_TX_WAIT(); \
        INT_SETFLAG(INUM_UART0_TX, INT_CLR); \
        UART_TX(x); \
    } while (0)

#define UART_WAIT_AND_RECEIVE(x) \
    do { \
        UART_RX_WAIT(); \
        UART_RX(x); \
        INT_SETFLAG(INUM_UART0_RX, INT_CLR); \  
} while (0)
//-------------------------------------------------------------------------------------------------------





/*******************************************************************************************************
 *******************************************************************************************************
 *******************************              SPI functions/macros        ******************************
 *******************************************************************************************************
 *******************************************************************************************************/
//-------------------------------------------------------------------------------------------------------
// This section contains useful macros and functions for setting up the SPI and for reading/writing
// CC2500 registers
//      SPI_INIT(freq)
//      SPI_ENABLE()
//      SPI_DISABLE()
//      SPI_WAIT()
//      void halSpiStrobe(BYTE addr)
//      void halSpiWriteReg(BYTE addr, BYTE value)
//      BYTE halSpiReadReg(BYTE addr)
//      void halSpiWriteBurstReg(BYTE addr, BYTE *buffer, BYTE count)
//      halSpiReadBurstReg(BYTE addr, BYTE *buffer, BYTE count)
//      RESET_CCxxx0()
//      POWER_UP_CCxxx0()
//-------------------------------------------------------------------------------------------------------




//-------------------------------------------------------------------------------------------------------
// Definitions to support burst/single access:
#define WRITE_BURST     0x40
#define READ_SINGLE     0x80
#define READ_BURST      0xC0
//-------------------------------------------------------------------------------------------------------




//-------------------------------------------------------------------------------------------------------
// SPI enable/disable macros:
#define SPI_ENABLE()        (SPI0CN |= BM_SPIEN)
#define SPI_DISABLE()       (SPI0CN &= ~BM_SPIEN)   
//-------------------------------------------------------------------------------------------------------




//-------------------------------------------------------------------------------------------------------
// Initialization
// Enble SPI (4-wire Single Master Mode, data centered on first edge of SCK period.
// SCK low in Idle State
#define SPI_INIT(freq) \
    do { \
        SPI0CFG = BM_MSTEN; \
        SPI0CN = BM_NSSMD1; \
        SPI0CKR = freq; \
        SPI_ENABLE(); \
    } while (0)

// where freq is one of:
#define SCLK_6_MHZ      1
#define SCLK_4_MHZ      2
#define SCLK_3_MHZ      3
#define SCLK_2_4_MHZ    4
#define SCLK_2_MHZ      5
#define SCLK_1_5_MHZ    7
#define SCLK_1_2_MHZ    9
#define SCLK_1_MHZ      11
//-------------------------------------------------------------------------------------------------------




//-------------------------------------------------------------------------------------------------------
// Macro used for communication data polling and wait on the SPI bus 
#define SPI_WAIT() \
    do { \
        while (!INT_GETFLAG(INUM_SPI0_IF)); \
        INT_SETFLAG(INUM_SPI0_IF, INT_CLR); \
    } while (0)
//-------------------------------------------------------------------------------------------------------




//-------------------------------------------------------------------------------------------------------
//  void halSpiStrobe(BYTE strobe)
//
//  DESCRIPTION:
//      Function for writing a strobe command to the CCxxx0
//
//  ARGUMENTS:
//      BYTE strobe
//          Strobe command
//-------------------------------------------------------------------------------------------------------
void halSpiStrobe(BYTE strobe);




//-------------------------------------------------------------------------------------------------------
//  BYTE halSpiReadStatus(BYTE addr)
//
//  DESCRIPTION:
//      This function reads a CCxxx0 status register.
//
//  ARGUMENTS:
//      BYTE addr
//          Address of the CCxxx0 status register to be accessed.
//
//  RETURN VALUE:
//      BYTE
//          Value of the accessed CCxxx0 status register.
//-------------------------------------------------------------------------------------------------------
BYTE halSpiReadStatus(BYTE addr);




//-------------------------------------------------------------------------------------------------------
//  void halSpiWriteReg(BYTE addr, BYTE value)
//
//  DESCRIPTION:
//      Function for writing to a single CCxxx0 register
//
//  ARGUMENTS:
//      BYTE addr
//          Address of a specific CCxxx0 register to accessed.
//      BYTE value
//          Value to be written to the specified CCxxx0 register.
//-------------------------------------------------------------------------------------------------------
void halSpiWriteReg(BYTE addr, BYTE value);




//-------------------------------------------------------------------------------------------------------
//  BYTE halSpiReadReg(BYTE addr)
//
//  DESCRIPTION:
//      This function gets the value of a single specified CCxxx0 register.
//
//  ARGUMENTS:
//      BYTE addr
//          Address of the CCxxx0 register to be accessed.
//
//  RETURN VALUE:
//      BYTE
//          Value of the accessed CCxxx0 register.
//-------------------------------------------------------------------------------------------------------
BYTE halSpiReadReg(BYTE addr);




//-------------------------------------------------------------------------------------------------------
//  void halSpiWriteBurstReg(BYTE addr, BYTE *buffer, BYTE count)
//
//  DESCRIPTION:
//      This function writes to multiple CCxxx0 register, using SPI burst access.
//
//  ARGUMENTS:
//      BYTE addr
//          Address of the first CCxxx0 register to be accessed.
//      BYTE *buffer
//          Array of bytes to be written into a corresponding range of
//          CCxx00 registers, starting by the address specified in _addr_.
//      BYTE count
//          Number of bytes to be written to the subsequent CCxxx0 registers.