📄 m2_0610.pin
字号:
-- Copyright (C) 1991-2007 Altera Corporation
-- Your use of Altera Corporation's design tools, logic functions
-- and other software and tools, and its AMPP partner logic
-- functions, and any output files from any of the foregoing
-- (including device programming or simulation files), and any
-- associated documentation or information are expressly subject
-- to the terms and conditions of the Altera Program License
-- Subscription Agreement, Altera MegaCore Function License
-- Agreement, or other applicable license agreement, including,
-- without limitation, that your use is for the sole purpose of
-- programming logic devices manufactured by Altera and sold by
-- Altera or its authorized distributors. Please refer to the
-- applicable agreement for further details.
--
-- This is a Quartus II output file. It is for reporting purposes only, and is
-- not intended for use as a Quartus II input file. This file cannot be used
-- to make Quartus II pin assignments - for instructions on how to make pin
-- assignments, please see Quartus II help.
---------------------------------------------------------------------------------
---------------------------------------------------------------------------------
-- NC : No Connect. This pin has no internal connection to the device.
-- VCCINT : Dedicated power pin, which MUST be connected to VCC (2.5V/3.3V).
-- VCCIO : Dedicated power pin, which MUST be connected to VCC
-- of its bank.
-- Bank 1: 3.3V
-- Bank 2: 3.3V
-- GND : Dedicated ground pin. Dedicated GND pins MUST be connected to GND.
-- It can also be used to report unused dedicated pins. The connection
-- on the board for unused dedicated pins depends on whether this will
-- be used in a future design. One example is device migration. When
-- using device migration, refer to the device pin-tables. If it is a
-- GND pin in the pin table or if it will not be used in a future design
-- for another purpose the it MUST be connected to GND. If it is an unused
-- dedicated pin, then it can be connected to a valid signal on the board
-- (low, high, or toggling) if that signal is required for a different
-- revision of the design.
-- GND+ : Unused input pin. It can also be used to report unused dual-purpose pins.
-- This pin should be connected to GND. It may also be connected to a
-- valid signal on the board (low, high, or toggling) if that signal
-- is required for a different revision of the design.
-- GND* : Unused I/O pin. This pin can either be left unconnected or
-- connected to GND. Connecting this pin to GND will improve the
-- device's immunity to noise.
-- RESERVED : Unused I/O pin, which MUST be left unconnected.
-- RESERVED_INPUT : Pin is tri-stated and should be connected to the board.
-- RESERVED_INPUT_WITH_WEAK_PULLUP : Pin is tri-stated with internal weak pull-up resistor.
-- RESERVED_INPUT_WITH_BUS_HOLD : Pin is tri-stated with bus-hold circuitry.
-- RESERVED_OUTPUT_DRIVEN_HIGH : Pin is output driven high.
---------------------------------------------------------------------------------
Quartus II Version 7.1 Build 156 04/30/2007 SJ Full Version
CHIP "M2_0610" ASSIGNED TO AN: EPM240T100C5
Pin Name/Usage : Location : Dir. : I/O Standard : Voltage : I/O Bank : User Assignment
-------------------------------------------------------------------------------------------------------------
CIN6 : 1 : input : 3.3-V LVTTL : : 2 : Y
CIN5 : 2 : input : 3.3-V LVTTL : : 1 : Y
CIN4 : 3 : input : 3.3-V LVTTL : : 1 : Y
CIN3 : 4 : input : 3.3-V LVTTL : : 1 : Y
CIN2 : 5 : input : 3.3-V LVTTL : : 1 : Y
CIN1 : 6 : input : 3.3-V LVTTL : : 1 : Y
TDRIB : 7 : output : 3.3-V LVTTL : : 1 : Y
RESERVED_INPUT : 8 : : : : 1 :
VCCIO1 : 9 : power : : 3.3V : 1 :
GNDIO : 10 : gnd : : : :
GNDINT : 11 : gnd : : : :
CLKIN : 12 : input : 3.3-V LVTTL : : 1 : Y
VCCINT : 13 : power : : 3.3V : :
CO1 : 14 : output : 3.3-V LVTTL : : 1 : Y
CO2 : 15 : output : 3.3-V LVTTL : : 1 : Y
CO3 : 16 : output : 3.3-V LVTTL : : 1 : Y
CO4 : 17 : output : 3.3-V LVTTL : : 1 : Y
CO5 : 18 : output : 3.3-V LVTTL : : 1 : Y
CO6 : 19 : output : 3.3-V LVTTL : : 1 : Y
RESERVED_INPUT : 20 : : : : 1 :
RESERVED_INPUT : 21 : : : : 1 :
TMS : 22 : input : : : 1 :
TDI : 23 : input : : : 1 :
TCK : 24 : input : : : 1 :
TDO : 25 : output : : : 1 :
A15 : 26 : input : 3.3-V LVTTL : : 1 : Y
SDA : 27 : bidir : 3.3-V LVTTL : : 1 : Y
SCL : 28 : output : 3.3-V LVTTL : : 1 : Y
ADC_CLK : 29 : input : 3.3-V LVTTL : : 1 : Y
ADC_DATA : 30 : input : 3.3-V LVTTL : : 1 : Y
VCCIO1 : 31 : power : : 3.3V : 1 :
GNDIO : 32 : gnd : : : :
KIN : 33 : output : 3.3-V LVTTL : : 1 : Y
SON2 : 34 : output : 3.3-V LVTTL : : 1 : Y
AL_CL2 : 35 : output : 3.3-V LVTTL : : 1 : Y
SIN : 36 : input : 3.3-V LVTTL : : 1 : Y
RESERVED_INPUT : 37 : : : : 1 :
RESERVED_INPUT : 38 : : : : 1 :
RESERVED_INPUT : 39 : : : : 1 :
RESERVED_INPUT : 40 : : : : 1 :
XIN : 41 : input : 3.3-V LVTTL : : 1 : Y
HM1 : 42 : input : 3.3-V LVTTL : : 1 : Y
LMT_B : 43 : input : 3.3-V LVTTL : : 1 : Y
RESERVED_INPUT : 44 : : : : 1 :
VCCIO1 : 45 : power : : 3.3V : 1 :
GNDIO : 46 : gnd : : : :
LMT_A : 47 : input : 3.3-V LVTTL : : 1 : Y
SERDY1 : 48 : input : 3.3-V LVTTL : : 1 : Y
QF2 : 49 : input : 3.3-V LVTTL : : 1 : Y
RESERVED_INPUT : 50 : : : : 1 :
PUL : 51 : output : 3.3-V LVTTL : : 1 : Y
F2 : 52 : output : 3.3-V LVTTL : : 2 : Y
QF1 : 53 : input : 3.3-V LVTTL : : 2 : Y
QZ1 : 54 : input : 3.3-V LVTTL : : 2 : Y
Test1 : 55 : output : 3.3-V LVTTL : : 2 : Y
XINT2 : 56 : output : 3.3-V LVTTL : : 2 : Y
RESERVED_INPUT : 57 : : : : 2 :
RESERVED_INPUT : 58 : : : : 2 :
VCCIO2 : 59 : power : : 3.3V : 2 :
GNDIO : 60 : gnd : : : :
A14 : 61 : input : 3.3-V LVTTL : : 2 : Y
RESERVED_INPUT : 62 : : : : 2 :
VCCINT : 63 : power : : 3.3V : :
RESERVED_INPUT : 64 : : : : 2 :
GNDINT : 65 : gnd : : : :
RESERVED_INPUT : 66 : : : : 2 :
RESERVED_INPUT : 67 : : : : 2 :
RESERVED_INPUT : 68 : : : : 2 :
RESERVED_INPUT : 69 : : : : 2 :
RESERVED_INPUT : 70 : : : : 2 :
RD : 71 : input : 3.3-V LVTTL : : 2 : Y
WR : 72 : input : 3.3-V LVTTL : : 2 : Y
A0 : 73 : input : 3.3-V LVTTL : : 2 : Y
A1 : 74 : input : 3.3-V LVTTL : : 2 : Y
A2 : 75 : input : 3.3-V LVTTL : : 2 : Y
RESERVED_INPUT : 76 : : : : 2 :
A3 : 77 : input : 3.3-V LVTTL : : 2 : Y
RESERVED_INPUT : 78 : : : : 2 :
GNDIO : 79 : gnd : : : :
VCCIO2 : 80 : power : : 3.3V : 2 :
RESERVED_INPUT : 81 : : : : 2 :
RESERVED_INPUT : 82 : : : : 2 :
RESERVED_INPUT : 83 : : : : 2 :
RESERVED_INPUT : 84 : : : : 2 :
D[0] : 85 : bidir : 3.3-V LVTTL : : 2 : Y
D[1] : 86 : bidir : 3.3-V LVTTL : : 2 : Y
RESERVED_INPUT : 87 : : : : 2 :
RESERVED_INPUT : 88 : : : : 2 :
RESERVED_INPUT : 89 : : : : 2 :
RESERVED_INPUT : 90 : : : : 2 :
D[2] : 91 : bidir : 3.3-V LVTTL : : 2 : Y
RESERVED_INPUT : 92 : : : : 2 :
GNDIO : 93 : gnd : : : :
VCCIO2 : 94 : power : : 3.3V : 2 :
RESERVED_INPUT : 95 : : : : 2 :
D[3] : 96 : bidir : 3.3-V LVTTL : : 2 : Y
D[4] : 97 : bidir : 3.3-V LVTTL : : 2 : Y
D[5] : 98 : bidir : 3.3-V LVTTL : : 2 : Y
D[6] : 99 : bidir : 3.3-V LVTTL : : 2 : Y
D[7] : 100 : bidir : 3.3-V LVTTL : : 2 : Y
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -