genralua.pin
来自「飞机电气检测的界面程序设计」· PIN 代码 · 共 102 行
PIN
102 行
-- Copyright (C) 1991-2007 Altera Corporation
-- Your use of Altera Corporation's design tools, logic functions
-- and other software and tools, and its AMPP partner logic
-- functions, and any output files from any of the foregoing
-- (including device programming or simulation files), and any
-- associated documentation or information are expressly subject
-- to the terms and conditions of the Altera Program License
-- Subscription Agreement, Altera MegaCore Function License
-- Agreement, or other applicable license agreement, including,
-- without limitation, that your use is for the sole purpose of
-- programming logic devices manufactured by Altera and sold by
-- Altera or its authorized distributors. Please refer to the
-- applicable agreement for further details.
--
-- This is a Quartus II output file. It is for reporting purposes only, and is
-- not intended for use as a Quartus II input file. This file cannot be used
-- to make Quartus II pin assignments - for instructions on how to make pin
-- assignments, please see Quartus II help.
---------------------------------------------------------------------------------
---------------------------------------------------------------------------------
-- NC : No Connect. This pin has no internal connection to the device.
-- VCC : Dedicated power pin, which MUST be connected to VCC.
-- VCCIO : Dedicated power pin, which MUST be connected to VCC
-- of its bank.
-- GND : Dedicated ground pin. Dedicated GND pins MUST be connected to GND.
-- It can also be used to report unused dedicated pins. The connection
-- on the board for unused dedicated pins depends on whether this will
-- be used in a future design. One example is device migration. When
-- using device migration, refer to the device pin-tables. If it is a
-- GND pin in the pin table or if it will not be used in a future design
-- for another purpose the it MUST be connected to GND. If it is an unused
-- dedicated pin, then it can be connected to a valid signal on the board
-- (low, high, or toggling) if that signal is required for a different
-- revision of the design.
-- GND+ : Unused input pin. It can also be used to report unused dual-purpose pins.
-- This pin should be connected to GND. It may also be connected to a
-- valid signal on the board (low, high, or toggling) if that signal
-- is required for a different revision of the design.
-- GND* : Unused I/O pin. This pin can either be left unconnected or
-- connected to GND. Connecting this pin to GND will improve the
-- device's immunity to noise.
-- RESERVED : Unused I/O pin, which MUST be left unconnected.
-- RESERVED_INPUT : Pin is tri-stated and should be connected to the board.
-- RESERVED_INPUT_WITH_WEAK_PULLUP : Pin is tri-stated with internal weak pull-up resistor.
-- RESERVED_INPUT_WITH_BUS_HOLD : Pin is tri-stated with bus-hold circuitry.
-- RESERVED_OUTPUT_DRIVEN_HIGH : Pin is output driven high.
-- NON_MIGRATABLE: This pin cannot be migrated.
---------------------------------------------------------------------------------
Quartus II Version 7.1 Build 156 04/30/2007 SJ Full Version
CHIP "genralUa" ASSIGNED TO AN: EPM7032SLC44-10
Pin Name/Usage : Location : Dir. : I/O Standard : Voltage : I/O Bank : User Assignment
-------------------------------------------------------------------------------------------------------------
address[2] : 1 : input : TTL : : : Y
address[1] : 2 : input : TTL : : : Y
VCC : 3 : power : : : :
address[5] : 4 : input : TTL : : : Y
address[6] : 5 : input : TTL : : : Y
bse : 6 : input : TTL : : : Y
TDI : 7 : input : TTL : : : N
ke[1] : 8 : output : TTL : : : Y
ke[2] : 9 : output : TTL : : : Y
GND : 10 : gnd : : : :
ke[3] : 11 : output : TTL : : : Y
ke[4] : 12 : output : TTL : : : Y
TMS : 13 : input : TTL : : : N
ke[5] : 14 : output : TTL : : : Y
VCC : 15 : power : : : :
ke[6] : 16 : output : TTL : : : Y
ke[7] : 17 : output : TTL : : : Y
ke[8] : 18 : output : TTL : : : Y
ke[9] : 19 : output : TTL : : : Y
ke[10] : 20 : output : TTL : : : Y
ke[11] : 21 : output : TTL : : : Y
GND : 22 : gnd : : : :
VCC : 23 : power : : : :
ke[12] : 24 : output : TTL : : : Y
ke[13] : 25 : output : TTL : : : Y
ke[14] : 26 : output : TTL : : : Y
ke[15] : 27 : output : TTL : : : Y
ke[16] : 28 : output : TTL : : : Y
ke[17] : 29 : output : TTL : : : Y
GND : 30 : gnd : : : :
ke[18] : 31 : output : TTL : : : Y
TCK : 32 : input : TTL : : : N
ke[19] : 33 : output : TTL : : : Y
ke[20] : 34 : output : TTL : : : Y
VCC : 35 : power : : : :
ke[21] : 36 : output : TTL : : : Y
ke[22] : 37 : output : TTL : : : Y
TDO : 38 : output : TTL : : : N
ke[23] : 39 : output : TTL : : : Y
ke[24] : 40 : output : TTL : : : Y
ke[25] : 41 : output : TTL : : : Y
GND : 42 : gnd : : : :
address[4] : 43 : input : TTL : : : Y
address[3] : 44 : input : TTL : : : Y
⌨️ 快捷键说明
复制代码Ctrl + C
搜索代码Ctrl + F
全屏模式F11
增大字号Ctrl + =
减小字号Ctrl + -
显示快捷键?