rtl8129.c

Linux内核源代码 为压缩文件 是<<Linux内核>>一书中的源代码

									  PCI_COMMAND, new_command);
		}

		dev = pci_tbl[chip_idx].probe1(pdev, pci_bus, pci_device_fn, ioaddr, irq, chip_idx, cards_found);

		if (dev  && (pci_tbl[chip_idx].flags & PCI_COMMAND_MASTER)) {
			u8 pci_latency;
			pcibios_read_config_byte(pci_bus, pci_device_fn,
									 PCI_LATENCY_TIMER, &pci_latency);
			if (pci_latency < 32) {
				printk(KERN_NOTICE "  PCI latency timer (CFLT) is "
					   "unreasonably low at %d.  Setting to 64 clocks.\n",
					   pci_latency);
				pcibios_write_config_byte(pci_bus, pci_device_fn,
										  PCI_LATENCY_TIMER, 64);
			}
		}
		dev = 0;
		cards_found++;
	}

	return cards_found ? 0 : -ENODEV;
}

static struct net_device *rtl8129_probe1(struct pci_dev *pdev, int pci_bus,
										 int pci_devfn, long ioaddr,
										 int irq, int chip_idx, int found_cnt)
{
	static int did_version = 0;			/* Already printed version info. */
	struct rtl8129_private *tp;
	int i, option = found_cnt < MAX_UNITS ? options[found_cnt] : 0;
	struct net_device *dev;

	if (rtl8129_debug > 0  &&  did_version++ == 0)
		printk(KERN_INFO "%s", version);

	dev = init_etherdev(NULL, 0);
	if (dev == NULL)
		goto out;

	printk(KERN_INFO "%s: %s at %#lx, IRQ %d, ",
		   dev->name, pci_tbl[chip_idx].name, ioaddr, irq);

	/* Bring the chip out of low-power mode. */
	outb(0x00, ioaddr + Config1);

	if (read_eeprom(ioaddr, 0) != 0xffff) {
		for (i = 0; i < 3; i++) {
			((u16 *)(dev->dev_addr))[i] =
				le16_to_cpu(read_eeprom(ioaddr, i + 7));
		}
	} else {
		for (i = 0; i < 6; i++)
			dev->dev_addr[i] = inb(ioaddr + MAC0 + i);
	}
	for (i = 0; i < 5; i++)
		printk("%2.2x:", dev->dev_addr[i]);
	printk("%2.2x.\n", dev->dev_addr[i]);

	/* We do a request_region() to register /proc/ioports info. */
	if (!request_region(ioaddr, pci_tbl[chip_idx].io_size, dev->name))
		goto out_free_dev;

	dev->base_addr = ioaddr;
	dev->irq = irq;

	/* Some data structures must be quadword aligned. */
	tp = kmalloc(sizeof(*tp), GFP_KERNEL | GFP_DMA);
	if (tp == NULL)
		goto out_release_region;

	memset(tp, 0, sizeof(*tp));
	dev->priv = tp;

	tp->next_module = root_rtl8129_dev;
	root_rtl8129_dev = dev;

	tp->pdev = pdev;
	tp->chip_id = chip_idx;
	tp->pci_bus = pci_bus;
	tp->pci_devfn = pci_devfn;

	/* Find the connected MII xcvrs.
	   Doing this in open() would allow detecting external xcvrs later, but
	   takes too much time. */
	if (rtl_cap_tbl[chip_idx] & HAS_MII_XCVR) {
		int phy, phy_idx;
		for (phy = 0, phy_idx = 0; phy < 32 && phy_idx < sizeof(tp->phys);
			 phy++) {
			int mii_status = mdio_read(dev, phy, 1);
			if (mii_status != 0xffff  && mii_status != 0x0000) {
				tp->phys[phy_idx++] = phy;
				printk(KERN_INFO "%s: MII transceiver found at address %d.\n",
					   dev->name, phy);
			}
		}
		if (phy_idx == 0) {
			printk(KERN_INFO "%s: No MII transceivers found!  Assuming SYM "
				   "transceiver.\n",
				   dev->name);
			tp->phys[0] = -1;
		}
	} else
		tp->phys[0] = 32;

	/* Put the chip into low-power mode. */
	outb(0xC0, ioaddr + Cfg9346);
	outb(0x03, ioaddr + Config1);
	outb('H', ioaddr + HltClk);		/* 'R' would leave the clock running. */

	/* The lower four bits are the media type. */
	if (option > 0) {
		tp->full_duplex = (option & 0x200) ? 1 : 0;
		tp->default_port = option & 15;
		if (tp->default_port)
			tp->medialock = 1;
	}

	if (found_cnt < MAX_UNITS  &&  full_duplex[found_cnt] > 0)
		tp->full_duplex = full_duplex[found_cnt];

	if (tp->full_duplex) {
		printk(KERN_INFO "%s: Media type forced to Full Duplex.\n", dev->name);
		mdio_write(dev, tp->phys[0], 4, 0x141);
		tp->duplex_lock = 1;
	}

	/* The Rtl8129-specific entries in the device structure. */
	dev->open = &rtl8129_open;
	dev->hard_start_xmit = &rtl8129_start_xmit;
	dev->tx_timeout = &rtl8129_tx_timeout;
	dev->watchdog_timeo = TX_TIMEOUT;
	dev->stop = &rtl8129_close;
	dev->get_stats = &rtl8129_get_stats;
	dev->set_multicast_list = &set_rx_mode;
	dev->do_ioctl = &mii_ioctl;
	return dev;

out_release_region:
	release_region(ioaddr, pci_tbl[chip_idx].io_size);
out_free_dev:
	unregister_netdev(dev);
	kfree(dev);
out:
	return NULL;
}

/* Serial EEPROM section. */

/*  EEPROM_Ctrl bits. */
#define EE_SHIFT_CLK	0x04	/* EEPROM shift clock. */
#define EE_CS			0x08	/* EEPROM chip select. */
#define EE_DATA_WRITE	0x02	/* EEPROM chip data in. */
#define EE_WRITE_0		0x00
#define EE_WRITE_1		0x02
#define EE_DATA_READ	0x01	/* EEPROM chip data out. */
#define EE_ENB			(0x80 | EE_CS)

/* Delay between EEPROM clock transitions.
   No extra delay is needed with 33Mhz PCI, but 66Mhz may change this.
 */

#define eeprom_delay()	inl(ee_addr)

/* The EEPROM commands include the alway-set leading bit. */
#define EE_WRITE_CMD	(5 << 6)
#define EE_READ_CMD		(6 << 6)
#define EE_ERASE_CMD	(7 << 6)

static int read_eeprom(long ioaddr, int location)
{
	int i;
	unsigned retval = 0;
	long ee_addr = ioaddr + Cfg9346;
	int read_cmd = location | EE_READ_CMD;

	outb(EE_ENB & ~EE_CS, ee_addr);
	outb(EE_ENB, ee_addr);

	/* Shift the read command bits out. */
	for (i = 10; i >= 0; i--) {
		int dataval = (read_cmd & (1 << i)) ? EE_DATA_WRITE : 0;
		outb(EE_ENB | dataval, ee_addr);
		eeprom_delay();
		outb(EE_ENB | dataval | EE_SHIFT_CLK, ee_addr);
		eeprom_delay();
	}
	outb(EE_ENB, ee_addr);
	eeprom_delay();

	for (i = 16; i > 0; i--) {
		outb(EE_ENB | EE_SHIFT_CLK, ee_addr);
		eeprom_delay();
		retval = (retval << 1) | ((inb(ee_addr) & EE_DATA_READ) ? 1 : 0);
		outb(EE_ENB, ee_addr);
		eeprom_delay();
	}

	/* Terminate the EEPROM access. */
	outb(~EE_CS, ee_addr);
	return retval;
}

/* MII serial management: mostly bogus for now. */
/* Read and write the MII management registers using software-generated
   serial MDIO protocol.
   The maximum data clock rate is 2.5 Mhz.  The minimum timing is usually
   met by back-to-back PCI I/O cycles, but we insert a delay to avoid
   "overclocking" issues. */
#define MDIO_DIR		0x80
#define MDIO_DATA_OUT	0x04
#define MDIO_DATA_IN	0x02
#define MDIO_CLK		0x01
#define MDIO_WRITE0 (MDIO_DIR)
#define MDIO_WRITE1 (MDIO_DIR | MDIO_DATA_OUT)

#define mdio_delay()	inb(mdio_addr)

static char mii_2_8139_map[8] = {MII_BMCR, MII_BMSR, 0, 0, NWayAdvert,
								 NWayLPAR, NWayExpansion, 0 };

/* Syncronize the MII management interface by shifting 32 one bits out. */
static void mdio_sync(long mdio_addr)
{
	int i;

	for (i = 32; i >= 0; i--) {
		outb(MDIO_WRITE1, mdio_addr);
		mdio_delay();
		outb(MDIO_WRITE1 | MDIO_CLK, mdio_addr);
		mdio_delay();
	}
	return;
}
static int mdio_read(struct net_device *dev, int phy_id, int location)
{
	long mdio_addr = dev->base_addr + MII_SMI;
	int mii_cmd = (0xf6 << 10) | (phy_id << 5) | location;
	int retval = 0;
	int i;

	if (phy_id > 31) {	/* Really a 8139.  Use internal registers. */
		return location < 8 && mii_2_8139_map[location] ?
			inw(dev->base_addr + mii_2_8139_map[location]) : 0;
	}
	mdio_sync(mdio_addr);
	/* Shift the read command bits out. */
	for (i = 15; i >= 0; i--) {
		int dataval = (mii_cmd & (1 << i)) ? MDIO_DATA_OUT : 0;

		outb(MDIO_DIR | dataval, mdio_addr);
		mdio_delay();
		outb(MDIO_DIR | dataval | MDIO_CLK, mdio_addr);
		mdio_delay();
	}

	/* Read the two transition, 16 data, and wire-idle bits. */
	for (i = 19; i > 0; i--) {
		outb(0, mdio_addr);
		mdio_delay();
		retval = (retval << 1) | ((inb(mdio_addr) & MDIO_DATA_IN) ? 1 : 0);
		outb(MDIO_CLK, mdio_addr);
		mdio_delay();
	}
	return (retval>>1) & 0xffff;
}

static void mdio_write(struct net_device *dev, int phy_id, int location, int value)
{
	long mdio_addr = dev->base_addr + MII_SMI;
	int mii_cmd = (0x5002 << 16) | (phy_id << 23) | (location<<18) | value;
	int i;

	if (phy_id > 31) {	/* Really a 8139.  Use internal registers. */
		if (location < 8  &&  mii_2_8139_map[location])
			outw(value, dev->base_addr + mii_2_8139_map[location]);
		return;
	}
	mdio_sync(mdio_addr);

	/* Shift the command bits out. */
	for (i = 31; i >= 0; i--) {
		int dataval = (mii_cmd & (1 << i)) ? MDIO_WRITE1 : MDIO_WRITE0;
		outb(dataval, mdio_addr);
		mdio_delay();
		outb(dataval | MDIO_CLK, mdio_addr);
		mdio_delay();
	}
	/* Clear out extra bits. */
	for (i = 2; i > 0; i--) {
		outb(0, mdio_addr);
		mdio_delay();
		outb(MDIO_CLK, mdio_addr);
		mdio_delay();
	}
	return;
}


static int
rtl8129_open(struct net_device *dev)
{
	struct rtl8129_private *tp = (struct rtl8129_private *)dev->priv;
	long ioaddr = dev->base_addr;
	int i, retval;

	MOD_INC_USE_COUNT;

	/* Soft reset the chip. */
	outb(CmdReset, ioaddr + ChipCmd);

	if ((retval = request_irq(dev->irq, &rtl8129_interrupt, SA_SHIRQ, dev->name, dev))) {
		MOD_DEC_USE_COUNT;
		return retval;
	}

	tp->tx_bufs = pci_alloc_consistent(tp->pdev,
									   TX_BUF_SIZE * NUM_TX_DESC,
									   &tp->tx_bufs_dma);
	tp->rx_ring = pci_alloc_consistent(tp->pdev,
									   RX_BUF_LEN + 16,
									   &tp->rx_ring_dma);
	if (tp->tx_bufs == NULL ||  tp->rx_ring == NULL) {
		free_irq(dev->irq, dev);
		if (tp->tx_bufs)
			pci_free_consistent(tp->pdev,
								TX_BUF_SIZE * NUM_TX_DESC,
								tp->tx_bufs, tp->tx_bufs_dma);
		if (tp->rx_ring)
			pci_free_consistent(tp->pdev,
								RX_BUF_LEN + 16,
								tp->rx_ring, tp->rx_ring_dma);
		if (rtl8129_debug > 0)
			printk(KERN_ERR "%s: Couldn't allocate a %d byte receive ring.\n",
				   dev->name, RX_BUF_LEN);
		MOD_DEC_USE_COUNT;
		return -ENOMEM;
	}
	rtl8129_init_ring(dev);

	/* Check that the chip has finished the reset. */
	for (i = 1000; i > 0; i--)
		if ((inb(ioaddr + ChipCmd) & CmdReset) == 0)
			break;

	for (i = 0; i < 6; i++)
		outb(dev->dev_addr[i], ioaddr + MAC0 + i);

	/* Must enable Tx/Rx before setting transfer thresholds! */
	outb(CmdRxEnb | CmdTxEnb, ioaddr + ChipCmd);
	outl((RX_FIFO_THRESH << 13) | (RX_BUF_LEN_IDX << 11) | (RX_DMA_BURST<<8),
		 ioaddr + RxConfig);
	outl((TX_DMA_BURST<<8)|0x03000000, ioaddr + TxConfig);
	tp->tx_flag = (TX_FIFO_THRESH<<11) & 0x003f0000;

	tp->full_duplex = tp->duplex_lock;
	if (tp->phys[0] >= 0  ||  (rtl_cap_tbl[tp->chip_id] & HAS_MII_XCVR)) {
		u16 mii_reg5 = mdio_read(dev, tp->phys[0], 5);
		if (mii_reg5 == 0xffff)
			;					/* Not there */
		else if ((mii_reg5 & 0x0100) == 0x0100
				 || (mii_reg5 & 0x00C0) == 0x0040)
			tp->full_duplex = 1;
		if (rtl8129_debug > 1)
			printk(KERN_INFO"%s: Setting %s%s-duplex based on"
				   " auto-negotiated partner ability %4.4x.\n", dev->name,
				   mii_reg5 == 0 ? "" :
				   (mii_reg5 & 0x0180) ? "100mbps " : "10mbps ",
				   tp->full_duplex ? "full" : "half", mii_reg5);
	}