config.in

Linux内核源代码 为压缩文件 是<<Linux内核>>一书中的源代码

#
# ATM device configuration
#
mainmenu_option next_comment
comment 'ATM drivers'
if [ "$CONFIG_INET" = "y" ]; then
   tristate 'ATM over TCP' CONFIG_ATM_TCP
fi
if [ "$CONFIG_PCI" = "y" ]; then
   tristate 'Efficient Networks ENI155P' CONFIG_ATM_ENI
   if [ "$CONFIG_ATM_ENI" != "n" ]; then
      bool '  Enable extended debugging' CONFIG_ATM_ENI_DEBUG
      bool '  Fine-tune burst settings' CONFIG_ATM_ENI_TUNE_BURST
      if [ "$CONFIG_ATM_ENI_TUNE_BURST" = "y" ]; then
	 bool '    Enable 16W TX bursts (discouraged)' CONFIG_ATM_ENI_BURST_TX_16W
	 bool '    Enable 8W TX bursts (recommended)' CONFIG_ATM_ENI_BURST_TX_8W
	 bool '    Enable 4W TX bursts (optional)' CONFIG_ATM_ENI_BURST_TX_4W
	 bool '    Enable 2W TX bursts (optional)' CONFIG_ATM_ENI_BURST_TX_2W
	 bool '    Enable 16W RX bursts (discouraged)' CONFIG_ATM_ENI_BURST_RX_16W
	 bool '    Enable 8W RX bursts (discouraged)' CONFIG_ATM_ENI_BURST_RX_8W
	 bool '    Enable 4W RX bursts (recommended)' CONFIG_ATM_ENI_BURST_RX_4W
	 bool '    Enable 2W RX bursts (optional)' CONFIG_ATM_ENI_BURST_RX_2W
      fi
   fi
   tristate 'Fujitsu FireStream (FS50/FS155) ' CONFIG_ATM_FIRESTREAM
   tristate 'ZeitNet ZN1221/ZN1225' CONFIG_ATM_ZATM
   if [ "$CONFIG_ATM_ZATM" != "n" ]; then
      bool '  Enable extended debugging' CONFIG_ATM_ZATM_DEBUG
      if [ "$CONFIG_X86" = "y" ]; then
	bool '  Enable usec resolution timestamps' CONFIG_ATM_ZATM_EXACT_TS
      fi
   fi
#   bool 'Rolfs TI TNETA1570' CONFIG_ATM_TNETA1570 y
#   if [ "$CONFIG_ATM_TNETA1570" = "y" ]; then
#      bool '  Enable extended debugging' CONFIG_ATM_TNETA1570_DEBUG n
#   fi
   tristate 'IDT 77201 (NICStAR) (ForeRunnerLE)' CONFIG_ATM_NICSTAR
   if [ "$CONFIG_ATM_NICSTAR" != "n" ]; then
      bool '  Use suni PHY driver (155Mbps)' CONFIG_ATM_NICSTAR_USE_SUNI
      bool '  Use IDT77015 PHY driver (25Mbps)' CONFIG_ATM_NICSTAR_USE_IDT77105
   fi
   tristate 'Madge Ambassador (Collage PCI 155 Server)' CONFIG_ATM_AMBASSADOR
   if [ "$CONFIG_ATM_AMBASSADOR" != "n" ]; then
      bool '  Enable debugging messages' CONFIG_ATM_AMBASSADOR_DEBUG
   fi
   tristate 'Madge Horizon [Ultra] (Collage PCI 25 and Collage PCI 155 Client)' CONFIG_ATM_HORIZON
   if [ "$CONFIG_ATM_HORIZON" != "n" ]; then
      bool '  Enable debugging messages' CONFIG_ATM_HORIZON_DEBUG
   fi
    tristate 'Interphase ATM PCI x575/x525/x531' CONFIG_ATM_IA
    if [ "$CONFIG_ATM_IA" != "n" ]; then
      bool '  Enable debugging messages' CONFIG_ATM_IA_DEBUG
    fi
fi
if [ "$CONFIG_PCI" = "y" -o "$CONFIG_SBUS" = "y" ]; then
  tristate 'FORE Systems 200E-series' CONFIG_ATM_FORE200E_MAYBE
  if [ "$CONFIG_ATM_FORE200E_MAYBE" != "n" ]; then
    if [ "$CONFIG_PCI" = "y" ]; then
      bool '  PCA-200E support' CONFIG_ATM_FORE200E_PCA y
      if [ "$CONFIG_ATM_FORE200E_PCA" = "y" ]; then
	bool '   Use default PCA-200E firmware (normally enabled)' CONFIG_ATM_FORE200E_PCA_DEFAULT_FW
        if [ "$CONFIG_ATM_FORE200E_PCA_DEFAULT_FW" = "n" ]; then
          string '   Pathname of user-supplied binary firmware' CONFIG_ATM_FORE200E_PCA_FW ""
        fi
      fi
    fi
    if [ "$CONFIG_SBUS" = "y" ]; then
      bool '  SBA-200E support' CONFIG_ATM_FORE200E_SBA y
      if [ "$CONFIG_ATM_FORE200E_SBA" = "y" ]; then
        bool '   Use default SBA-200E firmware (normally enabled)' CONFIG_ATM_FORE200E_SBA_DEFAULT_FW
        if [ "$CONFIG_ATM_FORE200E_SBA_DEFAULT_FW" = "n" ]; then
          string '   Pathname of user-supplied binary firmware' CONFIG_ATM_FORE200E_SBA_FW ""
        fi
      fi
    fi
  fi
  if [ "$CONFIG_ATM_FORE200E_PCA" = "y" -o "$CONFIG_ATM_FORE200E_SBA" = "y" ]; \
    then
    int  '  Maximum number of tx retries' CONFIG_ATM_FORE200E_TX_RETRY 16
    int  '  Debugging level (0-3)' CONFIG_ATM_FORE200E_DEBUG 0
    if [ "$CONFIG_ATM_FORE200E_MAYBE" = "y" ]; then
      define_tristate CONFIG_ATM_FORE200E y
    else
      define_tristate CONFIG_ATM_FORE200E m
    fi
  fi
fi
endmenu