📄 fir_top.pin
字号:
-- Copyright (C) 1991-2004 Altera Corporation
-- Any megafunction design, and related netlist (encrypted or decrypted),
-- support information, device programming or simulation file, and any other
-- associated documentation or information provided by Altera or a partner
-- under Altera's Megafunction Partnership Program may be used only
-- to program PLD devices (but not masked PLD devices) from Altera. Any
-- other use of such megafunction design, netlist, support information,
-- device programming or simulation file, or any other related documentation
-- or information is prohibited for any other purpose, including, but not
-- limited to modification, reverse engineering, de-compiling, or use with
-- any other silicon devices, unless such use is explicitly licensed under
-- a separate agreement with Altera or a megafunction partner. Title to the
-- intellectual property, including patents, copyrights, trademarks, trade
-- secrets, or maskworks, embodied in any such megafunction design, netlist,
-- support information, device programming or simulation file, or any other
-- related documentation or information provided by Altera or a megafunction
-- partner, remains with Altera, the megafunction partner, or their respective
-- licensors. No other licenses, including any licenses needed under any third
-- party's intellectual property, are provided herein.
---------------------------------------------------------------------------------
---------------------------------------------------------------------------------
-- NC : No Connect. This pin has no internal connection to the device.
-- VCCINT : Dedicated power pin, which MUST be connected to VCC (1.5V).
-- VCCIO : Dedicated power pin, which MUST be connected to VCC
-- of its bank.
-- Bank 1: 3.3V
-- Bank 2: 3.3V
-- Bank 3: 3.3V
-- Bank 4: 3.3V
-- Bank 5: 3.3V
-- Bank 6: 3.3V
-- Bank 7: 3.3V
-- Bank 8: 3.3V
-- Bank 9: 3.3V
-- Bank 10: 3.3V
-- Bank 11: 3.3V
-- Bank 12: 3.3V
-- GND : Dedicated ground pin. Dedicated GND pins MUST be connected to GND.
-- It can also be used to report unused dedicated pins. The connection
-- on the board for unused dedicated pins depends on whether this will
-- be used in a future design. One example is device migration. When
-- using device migration, refer to the device pin-tables. If it is a
-- GND pin in the pin table or if it will not be used in a future design
-- for another purpose the it MUST be connected to GND. If it is an unused
-- dedicated pin, then it can be connected to a valid signal on the board
-- (low, high, or toggling) if that signal is required for a different
-- revision of the design.
-- GND+ : Unused input pin. It can also be used to report unused dual-purpose pins.
-- This pin should be connected to GND. It may also be connected to a
-- valid signal on the board (low, high, or toggling) if that signal
-- is required for a different revision of the design.
-- GND* : Unused I/O pin. This pin can either be left unconnected or
-- connected to GND. Connecting this pin to GND will improve the
-- device's immunity to noise.
---------------------------------------------------------------------------------
Quartus II Version 4.0 Build 187 1/20/2004 SJ Full Version
CHIP "fir_top" ASSIGNED TO AN: EP1S10B672C6
Pin Name/Usage : Location : Dir. : I/O Standard : Voltage : I/O Bank : User Assignment
-------------------------------------------------------------------------------------------------------------
GND : A2 : gnd : : : 1 :
GND* : A3 : : : : 3 :
VCCIO3 : A4 : power : : 3.3V : 3 :
GND* : A5 : : : : 3 :
GND* : A6 : : : : 3 :
GND* : A7 : : : : 3 :
GND* : A8 : : : : 3 :
GND* : A9 : : : : 3 :
GND* : A10 : : : : 3 :
VCCIO3 : A11 : power : : 3.3V : 3 :
GND* : A12 : : : : 3 :
GND : A13 : gnd : : : 1 :
GND : A14 : gnd : : : 1 :
GND+ : A15 : : : : 4 :
VCCIO4 : A16 : power : : 3.3V : 4 :
GND* : A17 : : : : 4 :
NC : A18 : : : : 1 :
GND* : A19 : : : : 4 :
GND* : A20 : : : : 4 :
GND* : A21 : : : : 4 :
GND* : A22 : : : : 4 :
VCCIO4 : A23 : power : : 3.3V : 4 :
GND* : A24 : : : : 4 :
GND : A25 : gnd : : : 1 :
fir_result[20] : AA1 : output : LVTTL : : 1 : N
fir_result[21] : AA2 : output : LVTTL : : 1 : N
fir_result[11] : AA3 : output : LVTTL : : 1 : N
fir_result[25] : AA4 : output : LVTTL : : 1 : N
GND* : AA5 : : : : 1 :
GND* : AA6 : : : : 1 :
fir_result[10] : AA7 : output : LVTTL : : 8 : N
fir_result[4] : AA8 : output : LVTTL : : 8 : N
fir_result[0] : AA9 : output : LVTTL : : 8 : N
fir_result[19] : AA10 : output : LVTTL : : 8 : N
GND* : AA11 : : : : 8 :
GND* : AA12 : : : : 11 :
GND* : AA13 : : : : 11 :
GND* : AA14 : : : : 11 :
nIO_PULLUP : AA15 : : : : 7 :
NC : AA16 : : : : 1 :
GND* : AA17 : : : : 7 :
GND* : AA18 : : : : 7 :
GND* : AA19 : : : : 7 :
GND* : AA20 : : : : 7 :
GND* : AA21 : : : : 7 :
GND* : AA22 : : : : 6 :
GND* : AA23 : : : : 6 :
GND* : AA24 : : : : 6 :
GND* : AA25 : : : : 6 :
GND* : AA26 : : : : 6 :
NC : AB1 : : : : 1 :
NC : AB2 : : : : 1 :
GND* : AB3 : : : : 1 :
GND* : AB4 : : : : 1 :
data_in[5] : AB5 : input : LVTTL : : 8 : N
NC : AB6 : : : : 1 :
fir_result[8] : AB7 : output : LVTTL : : 8 : N
NC : AB8 : : : : 1 :
done : AB9 : output : LVTTL : : 8 : N
fir_result[16] : AB10 : output : LVTTL : : 8 : N
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -