cs8900.h

16位单片机接以太网芯片实现web功能。

/******************************************************************
 *****                                                        *****
 *****  Name: cs8900.h                                        *****
 *****  Ver.: 1.0                                             *****
 *****  Date: November 2001                                   *****
 *****  Auth: Andreas Dannenberg                              *****
 *****  Func: header-file for cs8900.c                        *****
 *****                                                        *****
 ******************************************************************/

#ifndef __CS8900_H
#define __CS8900_H

#define MYMAC_1              1                   // our ethernet (MAC) address
#define MYMAC_2              2                   // (MUST be unique in LAN!)
#define MYMAC_3              3
#define MYMAC_4              4
#define MYMAC_5              5
#define MYMAC_6              6

#define IOR                  BIT6                // CS8900's ISA-bus interface pins
#define IOW                  BIT7

// definitions for Crystal CS8900 ethernet-controller
// based on linux-header by Russel Nelson

#define PP_ChipID            0x0000              // offset 0h -> Corp-ID
                                                 // offset 2h -> Model/Product Number
                                                 // offset 3h -> Chip Revision Number

#define PP_ISAIOB            0x0020              // IO base address
#define PP_CS8900_ISAINT     0x0022              // ISA interrupt select
#define PP_CS8900_ISADMA     0x0024              // ISA Rec DMA channel
#define PP_ISASOF            0x0026              // ISA DMA offset
#define PP_DmaFrameCnt       0x0028              // ISA DMA Frame count
#define PP_DmaByteCnt        0x002A              // ISA DMA Byte count
#define PP_CS8900_ISAMemB    0x002C              // Memory base
#define PP_ISABootBase       0x0030              // Boot Prom base
#define PP_ISABootMask       0x0034              // Boot Prom Mask

// EEPROM data and command registers
#define PP_EECMD             0x0040              // NVR Interface Command register
#define PP_EEData            0x0042              // NVR Interface Data Register

// Configuration and control registers
#define PP_RxCFG             0x0102              // Rx Bus config
#define PP_RxCTL             0x0104              // Receive Control Register
#define PP_TxCFG             0x0106              // Transmit Config Register
#define PP_TxCMD             0x0108              // Transmit Command Register
#define PP_BufCFG            0x010A              // Bus configuration Register
#define PP_LineCTL           0x0112              // Line Config Register
#define PP_SelfCTL           0x0114              // Self Command Register
#define PP_BusCTL            0x0116              // ISA bus control Register
#define PP_TestCTL           0x0118              // Test Register

// Status and Event Registers
#define PP_ISQ               0x0120              // Interrupt Status
#define PP_RxEvent           0x0124              // Rx Event Register
#define PP_TxEvent           0x0128              // Tx Event Register
#define PP_BufEvent          0x012C              // Bus Event Register
#define PP_RxMiss            0x0130              // Receive Miss Count
#define PP_TxCol             0x0132              // Transmit Collision Count
#define PP_LineST            0x0134              // Line State Register
#define PP_SelfST            0x0136              // Self State register
#define PP_BusST             0x0138              // Bus Status
#define PP_TDR               0x013C              // Time Domain Reflectometry

// Initiate Transmit Registers
#define PP_TxCommand         0x0144              // Tx Command
#define PP_TxLength          0x0146              // Tx Length

// Adress Filter Registers
#define PP_LAF               0x0150              // Hash Table
#define PP_IA                0x0158              // Physical Address Register

// Frame Location
#define PP_RxStatus          0x0400              // Receive start of frame
#define PP_RxLength          0x0402              // Receive Length of frame
#define PP_RxFrame           0x0404              // Receive frame pointer
#define PP_TxFrame           0x0A00              // Transmit frame pointer

// Primary I/O Base Address. If no I/O base is supplied by the user, then this
// can be used as the default I/O base to access the PacketPage Area.
#define DEFAULTIOBASE        0x0300

// PP_RxCFG - Receive  Configuration and Interrupt Mask bit definition - Read/write
#define SKIP_1               0x0040
#define RX_STREAM_ENBL       0x0080
#define RX_OK_ENBL           0x0100
#define RX_DMA_ONLY          0x0200
#define AUTO_RX_DMA          0x0400
#define BUFFER_CRC           0x0800
#define RX_CRC_ERROR_ENBL    0x1000
#define RX_RUNT_ENBL         0x2000
#define RX_EXTRA_DATA_ENBL   0x4000

// PP_RxCTL - Receive Control bit definition - Read/write
#define RX_IA_HASH_ACCEPT    0x0040
#define RX_PROM_ACCEPT       0x0080
#define RX_OK_ACCEPT         0x0100
#define RX_MULTCAST_ACCEPT   0x0200
#define RX_IA_ACCEPT         0x0400
#define RX_BROADCAST_ACCEPT  0x0800
#define RX_BAD_CRC_ACCEPT    0x1000
#define RX_RUNT_ACCEPT       0x2000
#define RX_EXTRA_DATA_ACCEPT 0x4000

// PP_TxCFG - Transmit Configuration Interrupt Mask bit definition - Read/write
#define TX_LOST_CRS_ENBL     0x0040
#define TX_SQE_ERROR_ENBL    0x0080
#define TX_OK_ENBL           0x0100
#define TX_LATE_COL_ENBL     0x0200
#define TX_JBR_ENBL          0x0400
#define TX_ANY_COL_ENBL      0x0800
#define TX_16_COL_ENBL       0x8000

// PP_TxCMD - Transmit Command bit definition - Read-only and
// PP_TxCommand - Write-only
#define TX_START_5_BYTES     0x0000
#define TX_START_381_BYTES   0x0040
#define TX_START_1021_BYTES  0x0080
#define TX_START_ALL_BYTES   0x00C0
#define TX_FORCE             0x0100
#define TX_ONE_COL           0x0200
#define TX_NO_CRC            0x1000
#define TX_RUNT              0x2000

// PP_BufCFG - Buffer Configuration Interrupt Mask bit definition - Read/write
#define GENERATE_SW_INTERRUPT      0x0040
#define RX_DMA_ENBL                0x0080
#define READY_FOR_TX_ENBL          0x0100
#define TX_UNDERRUN_ENBL           0x0200
#define RX_MISS_ENBL               0x0400
#define RX_128_BYTE_ENBL           0x0800
#define TX_COL_COUNT_OVRFLOW_ENBL  0x1000
#define RX_MISS_COUNT_OVRFLOW_ENBL 0x2000
#define RX_DEST_MATCH_ENBL         0x8000

// PP_LineCTL - Line Control bit definition - Read/write
#define SERIAL_RX_ON         0x0040
#define SERIAL_TX_ON         0x0080
#define AUI_ONLY             0x0100
#define AUTO_AUI_10BASET     0x0200
#define MODIFIED_BACKOFF     0x0800
#define NO_AUTO_POLARITY     0x1000
#define TWO_PART_DEFDIS      0x2000
#define LOW_RX_SQUELCH       0x4000

// PP_SelfCTL - Software Self Control bit definition - Read/write
#define POWER_ON_RESET       0x0040
#define SW_STOP              0x0100
#define SLEEP_ON             0x0200
#define AUTO_WAKEUP          0x0400
#define HCB0_ENBL            0x1000
#define HCB1_ENBL            0x2000
#define HCB0                 0x4000
#define HCB1                 0x8000

// PP_BusCTL - ISA Bus Control bit definition - Read/write
#define RESET_RX_DMA         0x0040
#define MEMORY_ON            0x0400
#define DMA_BURST_MODE       0x0800
#define IO_CHANNEL_READY_ON  0x1000
#define RX_DMA_SIZE_64K      0x2000
#define ENABLE_IRQ           0x8000

// PP_TestCTL - Test Control bit definition - Read/write
#define LINK_OFF             0x0080
#define ENDEC_LOOPBACK       0x0200
#define AUI_LOOPBACK         0x0400
#define BACKOFF_OFF          0x0800
#define FDX_8900             0x4000

// PP_RxEvent - Receive Event Bit definition - Read-only
#define RX_IA_HASHED         0x0040
#define RX_DRIBBLE           0x0080
#define RX_OK                0x0100
#define RX_HASHED            0x0200
#define RX_IA                0x0400
#define RX_BROADCAST         0x0800
#define RX_CRC_ERROR         0x1000
#define RX_RUNT              0x2000
#define RX_EXTRA_DATA        0x4000
#define HASH_INDEX_MASK      0xFC00              // Hash-Table Index Mask (6 Bit)

// PP_TxEvent - Transmit Event Bit definition - Read-only
#define TX_LOST_CRS          0x0040
#define TX_SQE_ERROR         0x0080
#define TX_OK                0x0100
#define TX_LATE_COL          0x0200
#define TX_JBR               0x0400
#define TX_16_COL            0x8000
#define TX_COL_COUNT_MASK    0x7800

// PP_BufEvent - Buffer Event Bit definition - Read-only
#define SW_INTERRUPT         0x0040
#define RX_DMA               0x0080
#define READY_FOR_TX         0x0100
#define TX_UNDERRUN          0x0200
#define RX_MISS              0x0400
#define RX_128_BYTE          0x0800
#define TX_COL_OVRFLW        0x1000
#define RX_MISS_OVRFLW       0x2000
#define RX_DEST_MATCH        0x8000

// PP_LineST - Ethernet Line Status bit definition - Read-only
#define LINK_OK              0x0080
#define AUI_ON               0x0100
#define TENBASET_ON          0x0200
#define POLARITY_OK          0x1000
#define CRS_OK               0x4000

// PP_SelfST - Chip Software Status bit definition
#define ACTIVE_33V           0x0040
#define INIT_DONE            0x0080
#define SI_BUSY              0x0100
#define EEPROM_PRESENT       0x0200
#define EEPROM_OK            0x0400
#define EL_PRESENT           0x0800
#define EE_SIZE_64           0x1000

// PP_BusST - ISA Bus Status bit definition
#define TX_BID_ERROR         0x0080
#define READY_FOR_TX_NOW     0x0100

// The following block defines the ISQ event types
#define ISQ_RX_EVENT         0x0004
#define ISQ_TX_EVENT         0x0008
#define ISQ_BUFFER_EVENT     0x000C
#define ISQ_RX_MISS_EVENT    0x0010
#define ISQ_TX_COL_EVENT     0x0012

#define ISQ_EVENT_MASK       0x003F              // ISQ mask to find out type of event

// Ports for I/O-Mode
#define RX_FRAME_PORT        0x0000
#define TX_FRAME_PORT        0x0000
#define TX_CMD_PORT          0x0004
#define TX_LEN_PORT          0x0006
#define ISQ_PORT             0x0008
#define ADD_PORT             0x000A
#define DATA_PORT            0x000C

#define AUTOINCREMENT        0x8000              // Bit mask to set Bit-15 for autoincrement

// EEProm Commands
#define EEPROM_WRITE_EN      0x00F0
#define EEPROM_WRITE_DIS     0x0000
#define EEPROM_WRITE_CMD     0x0100
#define EEPROM_READ_CMD      0x0200

// Receive Header of each packet in receive area of memory for DMA-Mode
#define RBUF_EVENT_LOW       0x0000              // Low byte of RxEvent
#define RBUF_EVENT_HIGH      0x0001              // High byte of RxEvent
#define RBUF_LEN_LOW         0x0002              // Length of received data - low byte
#define RBUF_LEN_HI          0x0003              // Length of received data - high byte
#define RBUF_HEAD_LEN        0x0004              // Length of this header

// typedefs
typedef struct {                                 // struct to store CS8900's
  unsigned int Addr;                             // init-sequence
  unsigned int Data;
} TInitSeq;

// constants
const unsigned char MyMAC[] =                    // "M1-M2-M3-M4-M5-M6"
{
  MYMAC_1, MYMAC_2, MYMAC_3,
  MYMAC_4, MYMAC_5, MYMAC_6
};

const TInitSeq InitSeq[] =
{
  PP_IA, MYMAC_1 + (MYMAC_2 << 8),               // set our MAC as Individual Address
  PP_IA + 2, MYMAC_3 + (MYMAC_4 << 8),
  PP_IA + 4, MYMAC_5 + (MYMAC_6 << 8),
  PP_LineCTL, SERIAL_RX_ON | SERIAL_TX_ON,       // configure the Physical Interface
  PP_RxCTL, RX_OK_ACCEPT | RX_IA_ACCEPT | RX_BROADCAST_ACCEPT
};

// prototypes
void Init8900(void);
void Write8900(unsigned char Address, unsigned int Data);
void WriteFrame8900(unsigned int Data);
unsigned int Read8900(unsigned char Address);
unsigned int ReadFrame8900(void);
unsigned int ReadHB1ST8900(unsigned char Address);
unsigned int ReadFrameBE8900(void);
void CopyToFrame8900(void *Source, unsigned int Size);
void CopyFromFrame8900(void *Dest, unsigned int Size);
void DummyReadFrame8900(unsigned int Size);
void RequestSend(unsigned int FrameSize);
unsigned int Rdy4Tx(void);

#endif