buf2440.v

2440_cpld_rev015_030826.zip

module BUF2440(clock,nReset,nEXTBUS,BUFDIR,BUFDIR1,nFCE,nOE,nGCS,nFWE,nFRE,dmaMode,nDmaStart,nDREQ,nDACK,addr,data,nWAIT_OD);
    input clock,nReset;
    input nDmaStart;
    input nFCE;
    input [1:0] dmaMode;
    input nDACK;
    output nDREQ;

    input [3:0] addr;      
    output [3:0] data;
    input [6:0] nGCS;
    input nOE;
    input nFWE;
    input nFRE;

    output nWAIT_OD;
    output nEXTBUS;
    output BUFDIR;
    output BUFDIR1;

    //unused temporarily
    wire [3:0] addr;
    wire nDmaStart;
    wire [1:0] dmaMode;
    wire nXDACK;
    wire clock;
    wire nReset;
    wire nFCE;

    wire [3:0] wdata;

//  wire nXDREQ;
//  wire [3:0] data;
    wire nWAIT;

    //why don't work?
    //assign nXDREQ = 1'bz;
    //assign data[3:0] = 4'bz;
    assign nWAIT_OD = (!nGCS[4] && !nWAIT) ? 1'b0:1'bz;
    assign data[3:0] = (!nGCS[4] && !nOE ) ? wdata:4'bz;
    assign BUFDIR1 = BUFDIR;

    DMATEST m0(clock,nReset,dmaMode,nDmaStart,nDREQ,nDACK,dmaState);
    WAITTEST w0(clock,nReset,nWAIT,wdata,nGCS[4],nOE); 
    //nGCS4 is used as the nCS signal for nWAIT test.

    BUFCTRL b0(nEXTBUS,nGCS,nFWE,nFRE);
    BUFDIR b1(BUFDIR,nOE,nFRE);
endmodule




module BUFCTRL(nEXTBUS,nGCS,nFWE,nFRE);
    output nEXTBUS;
    input [6:0] nGCS;
    input nFWE;
    input nFRE;

    assign nEXTBUS = nGCS[0] && nGCS[1] && nGCS[2] && nGCS[3] && nGCS[4] && nGCS[5] && nGCS[6] && nFWE && nFRE;
endmodule




module BUFDIR(BUFDIR,nOE,nFRE);
    output BUFDIR;
    input nOE;
    input nFRE;

    assign BUFDIR = !(nOE && nFRE);
endmodule




module DMATEST(clock,nReset,dmaMode,nDmaStart,nDREQ,nDACK,state);
    input clock,nReset;
    input nDmaStart;
    input [1:0] dmaMode;
    input nDACK;
    output nDREQ;
    output [4:0] state;
	
    reg nDREQ;
    reg enCounter;
    reg preset16,preset1;
    reg [4:0] state;
    reg [3:0] counter;
    reg snDACK;
    reg snDmaStart;

    parameter [1:0] HS16=1,WHOLE=2; //mode
    parameter [4:0] READY=0,HS0=1,HS1=2,HS2=3,HS3=4,
					HS4=5,WH0=6,FL0=7,DM0=8,ERR=9; 

    always @(posedge clock or negedge nReset) 
	begin 
	    if(!nReset)counter=0;
	    else if(enCounter)counter=counter-1;
	    else if(preset16)counter=0;
	    else if(preset1)counter=1;
	end
	
    //always @(negedge clock) //for more faster nXDREQ generation
    always @(posedge clock)   //because device is slow, negedge may not operate in 66Mhz
	begin
	    snDACK=nDACK;
	end

    always @(posedge clock)
	begin
	    snDmaStart=nDmaStart;
	end


//CAUTION:
//set dmaMode bits first. And then,set dmaStart bit.	
//After DMA is started, cleare dmaStart bit.
    always @(posedge clock or negedge nReset)
	begin
	    if(!nReset)
		state=READY;
	    else
		case(state)
		    READY: 
			if(!snDmaStart)
			    begin
				case(dmaMode)
				    HS16:state=HS0;
				    WHOLE:state=WH0;
				    default:state=READY;
				endcase
			    end
			else
			    state=READY;
		    HS0: state=HS1;
		    HS1:
			if(snDACK)
			    state=HS1;
			else
			    state=HS2;
		    HS2:
			if(snDACK==0)state=HS2;
			else state=HS3;
		    HS3:state=HS4; //counter--
 		    HS4:if(counter!=0)
			    state=HS1; //next DMA request.
			else begin
				if(!nDmaStart) //check dmaStart bit is cleared?
				    state=HS4; 
				else
				    state=READY;
			    end

		    WH0: state=HS1; 
		    FL0: state=FL0; //not implemented yet.
		    DM0: state=DM0; //not implemented yet.
		    default:state=ERR;
		endcase
	end


    always @(state)
	begin
	    preset16=0;
	    preset1=0;
	    nDREQ=1;
	    enCounter=0;
	    case(state)
		HS0:
		    preset16=1; 
		HS1: 
		    nDREQ=0;
		HS3:
		    enCounter=1;
		WH0:
		    preset1=1;
	    endcase
	end
endmodule



module WAITTEST(clock,nReset,nWAIT,data,nGCS,nOE);
    input clock,nReset;
    input nGCS,nOE;
    output nWAIT;
    output [3:0] data;

    reg nWAIT;
    reg preset;
    reg enCounter;
    reg [3:0] data;
    reg [2:0] wState;
    reg [3:0] counter;

    parameter [1:0] W0=0,W1=1,W2=2,W3=3,W4=4,W5=5,W6=6;
	
    always @(posedge clock or negedge nReset) 
	begin 
	    if(!nReset)counter=0;
	    else if(enCounter)counter=counter-1;
	    else if(preset)counter=0;
	end

    always @(posedge clock or negedge nReset)
	begin
	    if(!nReset)
		wState=W0;
	    else
		case(wState)
		    W0: if(nGCS)
			    wState=W0;
			else 
			    wState=W1;
		    W1: wState=W2;
		    W2: wState=W3;
		    W3:	if(counter>0)
		    	    wState=W3;
			else
			    wState=W4;
		    W4: wState=W5;
		    W5: if(nOE==0)
			    wState=W5;
			else 
			    if(nGCS==0)
				wState=W6;
			    else
				wState=W0;
		    W6: if(nGCS==0)
			    wState=W6;
			else
			    wState=W0;
		endcase
	end

    always @(wState)
	begin
	    preset=0; 
	    enCounter=0;
	    nWAIT=1;
	    data=4'b0101;
	    case(wState)
		W1: begin
			preset=1;
			nWAIT=0;
		    end
		W2: begin
			enCounter=1;
			nWAIT=0;
		    end
		W3: begin
			nWAIT=0;
			enCounter=1;
		    end
		W4: begin
			nWAIT=1;
			data=4'b1010;
		    end
		W5: data=4'b1010;
	    endcase
	end

endmodule