📄 ch8_matrix.pin
字号:
-- Copyright (C) 1991-2007 Altera Corporation
-- Your use of Altera Corporation's design tools, logic functions
-- and other software and tools, and its AMPP partner logic
-- functions, and any output files from any of the foregoing
-- (including device programming or simulation files), and any
-- associated documentation or information are expressly subject
-- to the terms and conditions of the Altera Program License
-- Subscription Agreement, Altera MegaCore Function License
-- Agreement, or other applicable license agreement, including,
-- without limitation, that your use is for the sole purpose of
-- programming logic devices manufactured by Altera and sold by
-- Altera or its authorized distributors. Please refer to the
-- applicable agreement for further details.
--
-- This is a Quartus II output file. It is for reporting purposes only, and is
-- not intended for use as a Quartus II input file. This file cannot be used
-- to make Quartus II pin assignments - for instructions on how to make pin
-- assignments, please see Quartus II help.
---------------------------------------------------------------------------------
---------------------------------------------------------------------------------
-- NC : No Connect. This pin has no internal connection to the device.
-- VCCINT : Dedicated power pin, which MUST be connected to VCC (1.2V).
-- VCCIO : Dedicated power pin, which MUST be connected to VCC
-- of its bank.
-- Bank 1: 3.3V
-- Bank 2: 3.3V
-- Bank 3: 3.3V
-- Bank 4: 3.3V
-- Bank 5: 3.3V
-- Bank 6: 3.3V
-- Bank 7: 3.3V
-- Bank 8: 3.3V
-- GND : Dedicated ground pin. Dedicated GND pins MUST be connected to GND.
-- It can also be used to report unused dedicated pins. The connection
-- on the board for unused dedicated pins depends on whether this will
-- be used in a future design. One example is device migration. When
-- using device migration, refer to the device pin-tables. If it is a
-- GND pin in the pin table or if it will not be used in a future design
-- for another purpose the it MUST be connected to GND. If it is an unused
-- dedicated pin, then it can be connected to a valid signal on the board
-- (low, high, or toggling) if that signal is required for a different
-- revision of the design.
-- GND+ : Unused input pin. It can also be used to report unused dual-purpose pins.
-- This pin should be connected to GND. It may also be connected to a
-- valid signal on the board (low, high, or toggling) if that signal
-- is required for a different revision of the design.
-- GND* : Unused I/O pin. This pin can either be left unconnected or
-- connected to GND. Connecting this pin to GND will improve the
-- device's immunity to noise.
-- RESERVED : Unused I/O pin, which MUST be left unconnected.
-- RESERVED_INPUT : Pin is tri-stated and should be connected to the board.
-- RESERVED_INPUT_WITH_WEAK_PULLUP : Pin is tri-stated with internal weak pull-up resistor.
-- RESERVED_INPUT_WITH_BUS_HOLD : Pin is tri-stated with bus-hold circuitry.
---------------------------------------------------------------------------------
Quartus II Version 7.0 Build 33 02/05/2007 SJ Full Version
CHIP "CH8_Matrix" ASSIGNED TO AN: EP2C70F896C8
Pin Name/Usage : Location : Dir. : I/O Standard : Voltage : I/O Bank : User Assignment
-------------------------------------------------------------------------------------------------------------
GND : A2 : gnd : : : :
led1 : A3 : output : 3.3-V LVTTL : : 3 : Y
VCCIO3 : A4 : power : : 3.3V : 3 :
RESERVED_INPUT : A5 : : : : 3 :
RESERVED_INPUT : A6 : : : : 3 :
led3 : A7 : output : 3.3-V LVTTL : : 3 : Y
Update1 : A8 : output : 3.3-V LVTTL : : 3 : Y
RESERVED_INPUT : A9 : : : : 3 :
RESERVED_INPUT : A10 : : : : 3 :
RESERVED_INPUT : A11 : : : : 3 :
RESERVED_INPUT : A12 : : : : 3 :
GND : A13 : gnd : : : :
RESERVED_INPUT : A14 : : : : 3 :
VCCIO3 : A15 : power : : 3.3V : 3 :
VCCIO4 : A16 : power : : 3.3V : 4 :
D_sin[0] : A17 : output : 3.3-V LVTTL : : 4 : Y
GND : A18 : gnd : : : :
D_sin[5] : A19 : output : 3.3-V LVTTL : : 4 : Y
D_sin[7] : A20 : output : 3.3-V LVTTL : : 4 : Y
RESERVED_INPUT : A21 : : : : 4 :
RESERVED_INPUT : A22 : : : : 4 :
RESERVED_INPUT : A23 : : : : 4 :
RESERVED_INPUT : A24 : : : : 4 :
D_sin[8] : A25 : output : 3.3-V LVTTL : : 4 : Y
D_sin[10] : A26 : output : 3.3-V LVTTL : : 4 : Y
VCCIO4 : A27 : power : : 3.3V : 4 :
D_sin[15] : A28 : output : 3.3-V LVTTL : : 4 : Y
GND : A29 : gnd : : : :
RESERVED_INPUT : AA1 : : : : 1 :
RESERVED_INPUT : AA2 : : : : 1 :
RESERVED_INPUT : AA3 : : : : 1 :
RESERVED_INPUT : AA4 : : : : 1 :
RESERVED_INPUT : AA5 : : : : 1 :
RESERVED_INPUT : AA6 : : : : 1 :
RESERVED_INPUT : AA7 : : : : 1 :
RESERVED_INPUT : AA8 : : : : 1 :
RESERVED_INPUT : AA9 : : : : 1 :
RESERVED_INPUT : AA10 : : : : 1 :
GND : AA11 : gnd : : : :
GND : AA12 : gnd : : : :
VCCINT : AA13 : power : : 1.2V : :
VCCINT : AA14 : power : : 1.2V : :
GND : AA15 : gnd : : : :
GND : AA16 : gnd : : : :
VCCINT : AA17 : power : : 1.2V : :
VCCINT : AA18 : power : : 1.2V : :
GND : AA19 : gnd : : : :
GND : AA20 : gnd : : : :
GND_PLL4 : AA21 : gnd : : : :
GND_PLL4 : AA22 : gnd : : : :
RESERVED_INPUT : AA23 : : : : 6 :
RESERVED_INPUT : AA24 : : : : 6 :
RESERVED_INPUT : AA25 : : : : 6 :
RESERVED_INPUT : AA26 : : : : 6 :
RESERVED_INPUT : AA27 : : : : 6 :
RESERVED_INPUT : AA28 : : : : 6 :
RESERVED_INPUT : AA29 : : : : 6 :
RESERVED_INPUT : AA30 : : : : 6 :
RESERVED_INPUT : AB1 : : : : 1 :
RESERVED_INPUT : AB2 : : : : 1 :
VCCIO1 : AB3 : power : : 3.3V : 1 :
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -