e1000_hw.h

intel E1000类型网卡驱动源代码,目前在2.4的内核下支持82573的芯片不是很好,其他都不错

#define E1000_82542_IP6AT    E1000_IP6AT
#define E1000_82542_WUPL     E1000_WUPL
#define E1000_82542_WUPM     E1000_WUPM
#define E1000_82542_FFLT     E1000_FFLT
#define E1000_82542_TDFH     0x08010
#define E1000_82542_TDFT     0x08018
#define E1000_82542_FFMT     E1000_FFMT
#define E1000_82542_FFVT     E1000_FFVT
#define E1000_82542_HOST_IF  E1000_HOST_IF

/* Statistics counters collected by the MAC */
struct e1000_hw_stats {
    uint64_t crcerrs;
    uint64_t algnerrc;
    uint64_t symerrs;
    uint64_t rxerrc;
    uint64_t mpc;
    uint64_t scc;
    uint64_t ecol;
    uint64_t mcc;
    uint64_t latecol;
    uint64_t colc;
    uint64_t dc;
    uint64_t tncrs;
    uint64_t sec;
    uint64_t cexterr;
    uint64_t rlec;
    uint64_t xonrxc;
    uint64_t xontxc;
    uint64_t xoffrxc;
    uint64_t xofftxc;
    uint64_t fcruc;
    uint64_t prc64;
    uint64_t prc127;
    uint64_t prc255;
    uint64_t prc511;
    uint64_t prc1023;
    uint64_t prc1522;
    uint64_t gprc;
    uint64_t bprc;
    uint64_t mprc;
    uint64_t gptc;
    uint64_t gorcl;
    uint64_t gorch;
    uint64_t gotcl;
    uint64_t gotch;
    uint64_t rnbc;
    uint64_t ruc;
    uint64_t rfc;
    uint64_t roc;
    uint64_t rjc;
    uint64_t mgprc;
    uint64_t mgpdc;
    uint64_t mgptc;
    uint64_t torl;
    uint64_t torh;
    uint64_t totl;
    uint64_t toth;
    uint64_t tpr;
    uint64_t tpt;
    uint64_t ptc64;
    uint64_t ptc127;
    uint64_t ptc255;
    uint64_t ptc511;
    uint64_t ptc1023;
    uint64_t ptc1522;
    uint64_t mptc;
    uint64_t bptc;
    uint64_t tsctc;
    uint64_t tsctfc;
};

/* Structure containing variables used by the shared code (e1000_hw.c) */
struct e1000_hw {
    uint8_t *hw_addr;
    e1000_mac_type mac_type;
    e1000_phy_type phy_type;
    uint32_t phy_init_script;
    e1000_media_type media_type;
    void *back;
    e1000_fc_type fc;
    e1000_bus_speed bus_speed;
    e1000_bus_width bus_width;
    e1000_bus_type bus_type;
    struct e1000_eeprom_info eeprom;
    e1000_ms_type master_slave;
    e1000_ms_type original_master_slave;
    e1000_ffe_config ffe_config_state;
    uint32_t asf_firmware_present;
    unsigned long io_base;
    uint32_t phy_id;
    uint32_t phy_revision;
    uint32_t phy_addr;
    uint32_t original_fc;
    uint32_t txcw;
    uint32_t autoneg_failed;
    uint32_t max_frame_size;
    uint32_t min_frame_size;
    uint32_t mc_filter_type;
    uint32_t num_mc_addrs;
    uint32_t collision_delta;
    uint32_t tx_packet_delta;
    uint32_t ledctl_default;
    uint32_t ledctl_mode1;
    uint32_t ledctl_mode2;
    uint16_t phy_spd_default;
    uint16_t autoneg_advertised;
    uint16_t pci_cmd_word;
    uint16_t fc_high_water;
    uint16_t fc_low_water;
    uint16_t fc_pause_time;
    uint16_t current_ifs_val;
    uint16_t ifs_min_val;
    uint16_t ifs_max_val;
    uint16_t ifs_step_size;
    uint16_t ifs_ratio;
    uint16_t device_id;
    uint16_t vendor_id;
    uint16_t subsystem_id;
    uint16_t subsystem_vendor_id;
    uint8_t revision_id;
    uint8_t autoneg;
    uint8_t mdix;
    uint8_t forced_speed_duplex;
    uint8_t wait_autoneg_complete;
    uint8_t dma_fairness;
    uint8_t mac_addr[NODE_ADDRESS_SIZE];
    uint8_t perm_mac_addr[NODE_ADDRESS_SIZE];
    boolean_t disable_polarity_correction;
    boolean_t speed_downgraded;
    e1000_smart_speed smart_speed;
    e1000_dsp_config dsp_config_state;
    boolean_t get_link_status;
    boolean_t serdes_link_down;
    boolean_t tbi_compatibility_en;
    boolean_t tbi_compatibility_on;
    boolean_t phy_reset_disable;
    boolean_t fc_send_xon;
    boolean_t fc_strict_ieee;
    boolean_t report_tx_early;
    boolean_t adaptive_ifs;
    boolean_t ifs_params_forced;
    boolean_t in_ifs_mode;
};


#define E1000_EEPROM_SWDPIN0   0x0001   /* SWDPIN 0 EEPROM Value */
#define E1000_EEPROM_LED_LOGIC 0x0020   /* Led Logic Word */
/* Register Bit Masks */
/* Device Control */
#define E1000_CTRL_FD       0x00000001  /* Full duplex.0=half; 1=full */
#define E1000_CTRL_BEM      0x00000002  /* Endian Mode.0=little,1=big */
#define E1000_CTRL_PRIOR    0x00000004  /* Priority on PCI. 0=rx,1=fair */
#define E1000_CTRL_LRST     0x00000008  /* Link reset. 0=normal,1=reset */
#define E1000_CTRL_TME      0x00000010  /* Test mode. 0=normal,1=test */
#define E1000_CTRL_SLE      0x00000020  /* Serial Link on 0=dis,1=en */
#define E1000_CTRL_ASDE     0x00000020  /* Auto-speed detect enable */
#define E1000_CTRL_SLU      0x00000040  /* Set link up (Force Link) */
#define E1000_CTRL_ILOS     0x00000080  /* Invert Loss-Of Signal */
#define E1000_CTRL_SPD_SEL  0x00000300  /* Speed Select Mask */
#define E1000_CTRL_SPD_10   0x00000000  /* Force 10Mb */
#define E1000_CTRL_SPD_100  0x00000100  /* Force 100Mb */
#define E1000_CTRL_SPD_1000 0x00000200  /* Force 1Gb */
#define E1000_CTRL_BEM32    0x00000400  /* Big Endian 32 mode */
#define E1000_CTRL_FRCSPD   0x00000800  /* Force Speed */
#define E1000_CTRL_FRCDPX   0x00001000  /* Force Duplex */
#define E1000_CTRL_SWDPIN0  0x00040000  /* SWDPIN 0 value */
#define E1000_CTRL_SWDPIN1  0x00080000  /* SWDPIN 1 value */
#define E1000_CTRL_SWDPIN2  0x00100000  /* SWDPIN 2 value */
#define E1000_CTRL_SWDPIN3  0x00200000  /* SWDPIN 3 value */
#define E1000_CTRL_SWDPIO0  0x00400000  /* SWDPIN 0 Input or output */
#define E1000_CTRL_SWDPIO1  0x00800000  /* SWDPIN 1 input or output */
#define E1000_CTRL_SWDPIO2  0x01000000  /* SWDPIN 2 input or output */
#define E1000_CTRL_SWDPIO3  0x02000000  /* SWDPIN 3 input or output */
#define E1000_CTRL_RST      0x04000000  /* Global reset */
#define E1000_CTRL_RFCE     0x08000000  /* Receive Flow Control enable */
#define E1000_CTRL_TFCE     0x10000000  /* Transmit flow control enable */
#define E1000_CTRL_RTE      0x20000000  /* Routing tag enable */
#define E1000_CTRL_VME      0x40000000  /* IEEE VLAN mode enable */
#define E1000_CTRL_PHY_RST  0x80000000  /* PHY Reset */

/* Device Status */
#define E1000_STATUS_FD         0x00000001      /* Full duplex.0=half,1=full */
#define E1000_STATUS_LU         0x00000002      /* Link up.0=no,1=link */
#define E1000_STATUS_FUNC_MASK  0x0000000C      /* PCI Function Mask */
#define E1000_STATUS_FUNC_0     0x00000000      /* Function 0 */
#define E1000_STATUS_FUNC_1     0x00000004      /* Function 1 */
#define E1000_STATUS_TXOFF      0x00000010      /* transmission paused */
#define E1000_STATUS_TBIMODE    0x00000020      /* TBI mode */
#define E1000_STATUS_SPEED_MASK 0x000000C0
#define E1000_STATUS_SPEED_10   0x00000000      /* Speed 10Mb/s */
#define E1000_STATUS_SPEED_100  0x00000040      /* Speed 100Mb/s */
#define E1000_STATUS_SPEED_1000 0x00000080      /* Speed 1000Mb/s */
#define E1000_STATUS_ASDV       0x00000300      /* Auto speed detect value */
#define E1000_STATUS_MTXCKOK    0x00000400      /* MTX clock running OK */
#define E1000_STATUS_PCI66      0x00000800      /* In 66Mhz slot */
#define E1000_STATUS_BUS64      0x00001000      /* In 64 bit slot */
#define E1000_STATUS_PCIX_MODE  0x00002000      /* PCI-X mode */
#define E1000_STATUS_PCIX_SPEED 0x0000C000      /* PCI-X bus speed */

/* Constants used to intrepret the masked PCI-X bus speed. */
#define E1000_STATUS_PCIX_SPEED_66  0x00000000 /* PCI-X bus speed  50-66 MHz */
#define E1000_STATUS_PCIX_SPEED_100 0x00004000 /* PCI-X bus speed  66-100 MHz */
#define E1000_STATUS_PCIX_SPEED_133 0x00008000 /* PCI-X bus speed 100-133 MHz */

/* EEPROM/Flash Control */
#define E1000_EECD_SK        0x00000001 /* EEPROM Clock */
#define E1000_EECD_CS        0x00000002 /* EEPROM Chip Select */
#define E1000_EECD_DI        0x00000004 /* EEPROM Data In */
#define E1000_EECD_DO        0x00000008 /* EEPROM Data Out */
#define E1000_EECD_FWE_MASK  0x00000030
#define E1000_EECD_FWE_DIS   0x00000010 /* Disable FLASH writes */
#define E1000_EECD_FWE_EN    0x00000020 /* Enable FLASH writes */
#define E1000_EECD_FWE_SHIFT 4
#define E1000_EECD_REQ       0x00000040 /* EEPROM Access Request */
#define E1000_EECD_GNT       0x00000080 /* EEPROM Access Grant */
#define E1000_EECD_PRES      0x00000100 /* EEPROM Present */
#define E1000_EECD_SIZE      0x00000200 /* EEPROM Size (0=64 word 1=256 word) */
#define E1000_EECD_ADDR_BITS 0x00000400 /* EEPROM Addressing bits based on type
                                         * (0-small, 1-large) */
#define E1000_EECD_TYPE      0x00002000 /* EEPROM Type (1-SPI, 0-Microwire) */
#ifndef E1000_EEPROM_GRANT_ATTEMPTS
#define E1000_EEPROM_GRANT_ATTEMPTS 1000 /* EEPROM # attempts to gain grant */
#endif

/* EEPROM Read */
#define E1000_EERD_START      0x00000001 /* Start Read */
#define E1000_EERD_DONE       0x00000010 /* Read Done */
#define E1000_EERD_ADDR_SHIFT 8
#define E1000_EERD_ADDR_MASK  0x0000FF00 /* Read Address */
#define E1000_EERD_DATA_SHIFT 16
#define E1000_EERD_DATA_MASK  0xFFFF0000 /* Read Data */

/* SPI EEPROM Status Register */
#define EEPROM_STATUS_RDY_SPI  0x01
#define EEPROM_STATUS_WEN_SPI  0x02
#define EEPROM_STATUS_BP0_SPI  0x04
#define EEPROM_STATUS_BP1_SPI  0x08
#define EEPROM_STATUS_WPEN_SPI 0x80

/* Extended Device Control */
#define E1000_CTRL_EXT_GPI0_EN   0x00000001 /* Maps SDP4 to GPI0 */
#define E1000_CTRL_EXT_GPI1_EN   0x00000002 /* Maps SDP5 to GPI1 */
#define E1000_CTRL_EXT_PHYINT_EN E1000_CTRL_EXT_GPI1_EN
#define E1000_CTRL_EXT_GPI2_EN   0x00000004 /* Maps SDP6 to GPI2 */
#define E1000_CTRL_EXT_GPI3_EN   0x00000008 /* Maps SDP7 to GPI3 */
#define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* Value of SW Defineable Pin 4 */
#define E1000_CTRL_EXT_SDP5_DATA 0x00000020 /* Value of SW Defineable Pin 5 */
#define E1000_CTRL_EXT_PHY_INT   E1000_CTRL_EXT_SDP5_DATA
#define E1000_CTRL_EXT_SDP6_DATA 0x00000040 /* Value of SW Defineable Pin 6 */
#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */
#define E1000_CTRL_EXT_SDP4_DIR  0x00000100 /* Direction of SDP4 0=in 1=out */
#define E1000_CTRL_EXT_SDP5_DIR  0x00000200 /* Direction of SDP5 0=in 1=out */
#define E1000_CTRL_EXT_SDP6_DIR  0x00000400 /* Direction of SDP6 0=in 1=out */
#define E1000_CTRL_EXT_SDP7_DIR  0x00000800 /* Direction of SDP7 0=in 1=out */
#define E1000_CTRL_EXT_ASDCHK    0x00001000 /* Initiate an ASD sequence */
#define E1000_CTRL_EXT_EE_RST    0x00002000 /* Reinitialize from EEPROM */
#define E1000_CTRL_EXT_IPS       0x00004000 /* Invert Power State */
#define E1000_CTRL_EXT_SPD_BYPS  0x00008000 /* Speed Select Bypass */
#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
#define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000
#define E1000_CTRL_EXT_LINK_MODE_TBI  0x00C00000
#define E1000_CTRL_EXT_WR_WMARK_MASK  0x03000000
#define E1000_CTRL_EXT_WR_WMARK_256   0x00000000
#define E1000_CTRL_EXT_WR_WMARK_320   0x01000000
#define E1000_CTRL_EXT_WR_WMARK_384   0x02000000
#define E1000_CTRL_EXT_WR_WMARK_448   0x03000000

/* MDI Control */
#define E1000_MDIC_DATA_MASK 0x0000FFFF
#define E1000_MDIC_REG_MASK  0x001F0000
#define E1000_MDIC_REG_SHIFT 16
#define E1000_MDIC_PHY_MASK  0x03E00000
#define E1000_MDIC_PHY_SHIFT 21
#define E1000_MDIC_OP_WRITE  0x04000000
#define E1000_MDIC_OP_READ   0x08000000
#define E1000_MDIC_READY     0x10000000
#define E1000_MDIC_INT_EN    0x20000000
#define E1000_MDIC_ERROR     0x40000000

/* LED Control */
#define E1000_LEDCTL_LED0_MODE_MASK       0x0000000F
#define E1000_LEDCTL_LED0_MODE_SHIFT      0
#define E1000_LEDCTL_LED0_IVRT            0x00000040
#define E1000_LEDCTL_LED0_BLINK           0x00000080
#define E1000_LEDCTL_LED1_MODE_MASK       0x00000F00
#define E1000_LEDCTL_LED1_MODE_SHIFT      8
#define E1000_LEDCTL_LED1_IVRT            0x00004000
#define E1000_LEDCTL_LED1_BLINK           0x00008000
#define E1000_LEDCTL_LED2_MODE_MASK       0x000F0000
#define E1000_LEDCTL_LED2_MODE_SHIFT      16
#define E1000_LEDCTL_LED2_IVRT            0x00400000
#define E1000_LEDCTL_LED2_BLINK           0x00800000
#define E1000_LEDCTL_LED3_MODE_MASK       0x0F000000
#define E1000_LEDCTL_LED3_MODE_SHIFT      24
#define E1000_LEDCTL_LED3_IVRT            0x40000000
#define E1000_LEDCTL_LED3_BLINK           0x80000000

#define E1000_LEDCTL_MODE_LINK_10_1000  0x0
#define E1000_LEDCTL_MODE_LINK_100_1000 0x1
#define E1000_LEDCTL_MODE_LINK_UP       0x2
#define E1000_LEDCTL_MODE_ACTIVITY      0x3