cpld_qq2812.pin

2812学习板 cpld 源代码,2812学习板的译码部分

 -- Copyright (C) 1991-2009 Altera Corporation
 -- Your use of Altera Corporation's design tools, logic functions 
 -- and other software and tools, and its AMPP partner logic 
 -- functions, and any output files from any of the foregoing 
 -- (including device programming or simulation files), and any 
 -- associated documentation or information are expressly subject 
 -- to the terms and conditions of the Altera Program License 
 -- Subscription Agreement, Altera MegaCore Function License 
 -- Agreement, or other applicable license agreement, including, 
 -- without limitation, that your use is for the sole purpose of 
 -- programming logic devices manufactured by Altera and sold by 
 -- Altera or its authorized distributors.  Please refer to the 
 -- applicable agreement for further details.
 -- 
 -- This is a Quartus II output file. It is for reporting purposes only, and is
 -- not intended for use as a Quartus II input file. This file cannot be used
 -- to make Quartus II pin assignments - for instructions on how to make pin
 -- assignments, please see Quartus II help.
 ---------------------------------------------------------------------------------



 ---------------------------------------------------------------------------------
 -- NC            : No Connect. This pin has no internal connection to the device.
 -- DNU           : Do Not Use. This pin MUST NOT be connected.
 -- VCCINT        : Dedicated power pin, which MUST be connected to VCC  (3.3V).
 -- VCCIO         : Dedicated power pin, which MUST be connected to VCC
 --                 of its bank.
 -- GND           : Dedicated ground pin. Dedicated GND pins MUST be connected to GND.
 --					It can also be used to report unused dedicated pins. The connection
 --					on the board for unused dedicated pins depends on whether this will
 --					be used in a future design. One example is device migration. When
 --					using device migration, refer to the device pin-tables. If it is a
 --					GND pin in the pin table or if it will not be used in a future design
 --					for another purpose the it MUST be connected to GND. If it is an unused
 --					dedicated pin, then it can be connected to a valid signal on the board
 --					(low, high, or toggling) if that signal is required for a different
 --					revision of the design.
 -- GND+          : Unused input pin. It can also be used to report unused dual-purpose pins.
 --					This pin should be connected to GND. It may also be connected  to a
 --					valid signal  on the board  (low, high, or toggling)  if that signal
 --					is required for a different revision of the design.
 -- GND*          : Unused  I/O  pin.   For transceiver I/O banks (Bank 13, 14, 15, 16 and 17),
 --           	    connect each pin marked GND* either individually through a 10k Ohm resistor
 --           	    to GND or tie all pins together and connect through a single 10k Ohm resistor
 --           	    to GND.
 --           	    For non-transceiver I/O banks, connect each pin marked GND* directly to GND
 --           	    or leave it unconnected.
 -- RESERVED      : Unused I/O pin, which MUST be left unconnected.
 -- RESERVED_INPUT    : Pin is tri-stated and should be connected to the board.
 -- RESERVED_INPUT_WITH_WEAK_PULLUP    : Pin is tri-stated with internal weak pull-up resistor.
 -- RESERVED_INPUT_WITH_BUS_HOLD       : Pin is tri-stated with bus-hold circuitry.
 -- RESERVED_OUTPUT_DRIVEN_HIGH        : Pin is output driven high.
 -- NON_MIGRATABLE: This pin cannot be migrated.
 ---------------------------------------------------------------------------------



 ---------------------------------------------------------------------------------
 -- Pin directions (input, output or bidir) are based on device operating in user mode.
 ---------------------------------------------------------------------------------

Quartus II Version 9.0 Build 132 02/25/2009 SJ Full Version
CHIP  "CPLD_QQ2812"  ASSIGNED TO AN: EPM3256AFC256-10

Pin Name/Usage               : Location  : Dir.   : I/O Standard      : Voltage : I/O Bank  : User Assignment
-------------------------------------------------------------------------------------------------------------
NC                           : A1        :        :                   :         :           :                
NC                           : A2        :        :                   :         :           :                
GND                          : A3        : gnd    :                   :         :           :                
OUT[8]                       : A4        : output : 3.3-V LVTTL       :         :           : N              
LED[0]                       : A5        : output : 3.3-V LVTTL       :         :           : N              
NC                           : A6        :        :                   :         :           :                
OUT[2]                       : A7        : output : 3.3-V LVTTL       :         :           : N              
GND                          : A8        : gnd    :                   :         :           :                
DSP_Add[3]                   : A9        : input  : 3.3-V LVTTL       :         :           : N              
RESERVED                     : A10       :        :                   :         :           :                
RESERVED                     : A11       :        :                   :         :           :                
NC                           : A12       :        :                   :         :           :                
NC                           : A13       :        :                   :         :           :                
NC                           : A14       :        :                   :         :           :                
NC                           : A15       :        :                   :         :           :                
NC                           : A16       :        :                   :         :           :                
NC                           : B1        :        :                   :         :           :                
NC                           : B2        :        :                   :         :           :                
VCCIO                        : B3        : power  :                   : 3.3V    :           :                
SIDIN                        : B4        : output : 3.3-V LVTTL       :         :           : N              
VCCIO                        : B5        : power  :                   : 3.3V    :           :                
LCD_Data[7]                  : B6        : output : 3.3-V LVTTL       :         :           : N              
LCD_Data[2]                  : B7        : output : 3.3-V LVTTL       :         :           : N              
LED[2]                       : B8        : output : 3.3-V LVTTL       :         :           : N              
VCCINT                       : B9        : power  :                   : 3.3V    :           :                
GND                          : B10       : gnd    :                   :         :           :                
RESERVED                     : B11       :        :                   :         :           :                
IN[11]                       : B12       : input  : 3.3-V LVTTL       :         :           : N              
RESERVED                     : B13       :        :                   :         :           :                
RESERVED                     : B14       :        :                   :         :           :                
NC                           : B15       :        :                   :         :           :                
NC                           : B16       :        :                   :         :           :                
NC                           : C1        :        :                   :         :           :                
GND                          : C2        : gnd    :                   :         :           :                
RESERVED                     : C3        :        :                   :         :           :                
DSP_Data[0]                  : C4        : bidir  : 3.3-V LVTTL       :         :           : N              
LCD_Data[1]                  : C5        : output : 3.3-V LVTTL       :         :           : N              
OUT[0]                       : C6        : output : 3.3-V LVTTL       :         :           : N              
CANRX                        : C7        : output : 3.3-V LVTTL       :         :           : N              
VCCINT                       : C8        : power  :                   : 3.3V    :           :                
GND                          : C9        : gnd    :                   :         :           :