boot51.doc

一份51的编译程序,dos版本的. 英文名字MCS-51 Microcontroller Family Macro Assembler

              MCS-51 Microcontroller Family Bootstrap Program






           BBBBBB    OOOOO    OOOOO  TTTTTTTT       5555555   11
           BB   BB  OO   OO  OO   OO    TT          55       111
           BB   BB  OO   OO  OO   OO    TT          55        11
           BBBBBB   OO   OO  OO   OO    TT    ====  555555    11
           BB   BB  OO   OO  OO   OO    TT               55   11
           BB   BB  OO   OO  OO   OO    TT               55   11
           BBBBBB    OOOOO    OOOOO     TT          555555   1111









                         U S E R ' S    M A N U A L

                                Version  1.1




                              December 15, 2002

















                copyright (c) 1996, 2002  by  W.W. Heinz



                          TABLE OF CONTENTS
                          -----------------



I.    Introduction

II.   BOOT-51 Installation

      II.1   Files
      II.2   Customizing BOOT-51
      II.3   Tailoring the Cables
      II.4   Design of MCS-51 Evaluation Boards

III.  BOOT-51 Operation

      III.1  Interactive Operation
      III.2  Batch File Operation under MS-DOS
      III.3  DOS Upload Utilities
      III.4  Shell Script Operation under Linux
      III.5  The BLINK Program

IV.   Troubleshooting

      IV.1   General Trouble
      IV.2   Trouble under MS-DOS
      IV.3   Trouble under Linux


Appendix A:  CUSTOMIZ Error Messages

      A.1    Parameter Errors
      A.2    Baudrate Errors
      A.3    Runtime Errors

Appendix B:  RESET51 Error Messages

Appendix C:  BOOT-51 Error Messages

Appendix D:  Trademarks

Appendix E:  Tables of Baudrates



I. Introduction
---------------
Usually an 8051 application program is not running correctly from scratch,
and it is not quite easy to debug it without a suitable test equipment.
It is very inconvenient, to burn the program into an EPROM after every
change. Instead it would be nice to load the program into the external
RAM of the target board and then start it. This would dramatically speed
up the turn-around cycles. However, three problems must be solved first:

  1. There must be a suitable interface to transmit the application
     program from the host (PC) to the target (8051) system.

  2. The target board needs a suitable firmware that can receive a
     program from the host computer, store it in the external RAM,
     and finally execute it.

  3. Once loaded, the application program must be executable, although
     it is stored in the external RAM, which is usually mapped into the
     XDATA address space.
     (Programs can only be executed in the CODE address space!)

The corresponding three solutions are:

  1. an RS-232 interface between the PC and the 8051 board
  2. a bootstrap program
  3. external RAM that is mapped into both the CODE and XDATA address space

Nearly all evaluation boards for 8051 derivatives are meeting requirements
1 and 3. In most cases, it is easy to establish a memory map according to
requirement 3, even on target boards that do not originally support it.
(See chapter "II.4 Design of MCS-51 Evaluation Boards".)

Requirement 2 can be met by burning a customized version of BOOT-51 into
the EPROM of the target board. After system reset, it can receive an
Intel-HEX file over the serial interface, store it in the external RAM,
and finally jump to the program start address.

BOOT-51 itself doesn't need any external RAM, and requires only 1 kB of
EPROM. In principle, it is not restricted to a PC-based host system, but
presently only the host platforms MS-DOS, Windows 9x, and Linux (i386)
are supported.

Sure, a bootstrap program cannot replace a target debugger, but it's a start.



II. BOOT-51 Installation
------------------------
The BOOT-51 support files are usually installed on the host system together
with the latest ASEM-51 version. Of course BOOT-51 must be installed on the
MCS-51 target system, too.
Before burning BOOT-51 into an EPROM, it must be customized for the target
board, and one or two cables must be tailored for local requirements.
If the design of the target system is not yet finished, some basic knowledge,
concerning the general design of MCS-51 evaluation boards, might be helpful
to meet the hardware requirements from the beginning.



II.1 Files
----------
The BOOT-51 package for DOS/Windows consists of the following files:

    BOOT51.DOC          BOOT-51 User's Manual, ASCII format
    BOOT51.HTM          index file of the BOOT-51 documentation, HTML format
         *.HTM          further pages of the HTML documentation
         *.GIF          GIF images referenced by HTML pages
    BOOT51.A51          BOOT-51 assembler source (for ASEM-51 V1.3 and up)
  CUSTOMIZ.EXE          BOOT-51 customization utility
      BOOT.BAT          batch file for application program upload
    UPLOAD.BAT          called by BOOT.BAT only
   COMPORT.EXE          setup utility for PC serial ports
   RESET51.EXE          program to reset the target system via PC ports
     SLEEP.EXE          program to wait for the reset recovery time
     BLINK.A51          sample test program for BOOT-51

The BOOT-51 package for Linux consists of the following files:

    boot51.doc          BOOT-51 User's Manual, ASCII format
    boot51.htm          index file of the BOOT-51 documentation, HTML format
         *.htm          further pages of the HTML documentation
         *.gif          GIF images referenced by HTML pages
    boot51.a51          BOOT-51 assembler source (for ASEM-51 V1.3 and up)
    customiz            BOOT-51 customization utility
    customiz.1          man-page for customiz
    boot                shell script for application program upload
    boot.1              man-page for boot
    upload              called by boot only (generic version)
    upload.new          "new" upload (optimized for stty 2.0 or later)
    reset51             program to reset the target system via PC ports
    reset51.1           man-page for reset51
    blink.a51           sample test program for BOOT-51



II.2 Customizing BOOT-51
------------------------
BOOT-51 must be customized for the target board, before it is ready for
assembly. This is performed with an include file boot51.inc, containing
the required configuration data. boot51.inc is generated with the BOOT-51
Customization Utility CUSTOMIZ.
There are two major groups of configuration parameters:

  -  baudrate generation
  -  memory addresses

CUSTOMIZ is invoked as shown below:


  customiz <baud> [<timer> [<prec> [<clock> [<start> [<user>]]]]]


The first four parameters are for baudrate generation, and the last two
parameters are memory addresses. Parameters in brackets are optional.
If CUSTOMIZ is invoked without parameters, it displays a help screen.

<baud>     is the desired nominal baudrate (in Baud), BOOT-51 should use
           for communication with the host system.

<timer>    is the on-chip timer or baudrate generator that is used for
           baudrate generation. Legal values are:

           T1 = timer 1, available on nearly all 8051 derivatives (default)
           T2 = timer 2, available on 8052/32 and all true compatibles
           BG = internal baudrate generator on 80C515/35 and 80C517/37
           BA = internal baudrate generator on 80C515A and 80C517A
           D1 = timer 1 with clock/12 or clock/4 prescaler on 80C320

<prec>     is the required relative precision of the baudrate in %.
           The default precision is 1.0 %.

<clock>    is the system clock frequency in MHz. (11.0592 MHz default)

<start>    is the start address of BOOT-51 on the target system in hex
           representation. (default is 0000H)

<user>     is the usual hex start address of the application programs
           in the external memory. (default is 8000H)

Baudrate:
---------
For the serial interface, the standard UART is used that is available on
almost every 8051 derivative. BOOT-51 is always running the UART in Mode 1,
that is asynchronous mode, 8 data bits, 1 stop bit, no parity.
However, depending on the derivative, there may be various timers or
prescalers that can be used for baudrate generation.
If the desired baudrate cannot be generated or the precision is too bad,
CUSTOMIZ will display a corresponding error message. In this case, try
another baudrate generator that is also available on your derivative.
If this fails, too, try another baudrate that may also do, or think of
using another oscillator crystal that suits better for the task.
You should play around with CUSTOMIZ, to explore how to get best results.
The tables in Appendix E show the precisions of the most frequently used
baudrates that can be generated with the supported timers and baudrate
generators, for some standard clock frequencies.
In most cases baudrate deviations of 2 to 3 % are no problem for the
communication with a PC. Whenever in doubt, try it!
BOOT-51 can receive data at very high baudrates without the need for a
handshake protocol. Output is done more slowly with short pauses between
the characters, to avoid a data overrun of the PC UART. The maximum
effective output speed of BOOT-51 is corresponding to 9600 Baud
(max. 1 character per ms).
In general, speed is rather a problem for the PC than for the micro.

Example 1:   customiz 9600 BG 0.1 12
----------
             will generate an include file for BOOT-51 that configures it
             for 9600 Baud, generated with the internal baudrate generator
             of a SAB80C535 or SAB80C537 that is clocked with 12.0 MHz.
             The required precision is 0.1 %.
             The bootstrap and application program start addresses are
             set to their default values.

Addresses:
----------

<start>:
An 8051 starts program execution at CODE address 0000H after reset.
Thus there must always be ROM at CODE address 0000H to execute the first
instructions. On most 8051 boards there is EPROM in the range 0000H-7FFFH,
and RAM in the range 8000H-FFFFH. However, the final application programs
will usually start at address 0000H, and the 8051 interrupt addresses start
at address 0003H. If application programs can be loaded into RAM at 8000H,
this is normally not quite realistic for testing.
Hence it would be nice to have CODE/XDATA-RAM at address 0000H to load and
test application programs. That is why some evaluation boards (e.g. the Keil
MCB-517) remap the EPROM from address 0000H to 8000H, and the RAM from 8000H
to 0000H, when the first memory access to a CODE address > 7FFFH occurs.
To support this, BOOT-51 starts with a long jump to its entry point, to
eventually remap the memory. If you own a corresponding evaluation board,
specify the <start> address of BOOT-51 to the location, where it resides
after memory remapping!

<user>:
In principle, BOOT-51 can load an application program at any location in
the external RAM and start it there. However, the interrupt addresses
should be redirected to the location, where application programs usually
start, e.g. the start address of the external RAM.
Hence the <user> address should point to the location, where the CODE/XDATA-
RAM starts. If it starts at 8000H, interrupt 0003H is redirected to 8003H,
interrupt 000BH to 800BH, and so on.
If the CODE/XDATA-RAM starts at 0000H (after remapping), the <user> address
has no practical meaning and can be left default.

Example 2:   customiz 19200 T2 1 11.0592 0 C000
----------
             will generate an include file for BOOT-51 that configures it
             for 19200 Baud, generated with timer 2 of an 80C52 or 80C32
             that is clocked with 11.0592 MHz. The required precision is 1 %.
             BOOT-51 is located at address 0000H in the EPROM, and the
             interrupt addresses are redirected to location 0C000H.

If CUSTOMIZ aborts with an error message, it returns exit code 1 on para-
meter- and baudrate-errors, and exit code 2 on fatal runtime errors.
When CUSTOMIZ terminates without error message, it returns exit code 0, and
a customization header file boot51.inc should be present in the default
directory. With this file, BOOT-51 can be assembled as usual with

              ASEM BOOT51                           (DOS)
              asem boot51.a51                       (Linux)

Remember that BOOT-51 requires ASEM-51 V1.3 or later!
Now there should be an Intel-HEX file boot51.hex, which may serve directly
as an input for the EPROM programmer. We may also convert it to a binary
image file with the HEXBIN utility:

             HEXBIN BOOT51/LENGTH:4000              (DOS)
             hexbin -l 4000 boot51.hex              (Linux)

would generate a binary image file boot51.bin for a 16 kB EPROM (27C128).
(Note: Only 1 kB of EPROM is required for the BOOT-51 program code.)
Once in an EPROM, BOOT-51 should be ready to run on the target system.



II.3 Tailoring the Cables
-------------------------
Application programs are uploaded to the target system over a serial
interface. The serial ports of the PC may have 9-pin or 25-pin male
D-Shell connectors. Suitable RS-232 cables for the MCS-51 board can
be tailored as follows:


   RS-232 cable with 25-pin female D-Shell connector:
   --------------------------------------------------