📄 bmsdos.htm

📁 一份51的编译程序,dos版本的. 英文名字MCS-51 Microcontroller Family Macro Assembler
💻 HTM
字号:
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">

<!-- Trouble under MS-DOS -->

<HTML>

<HEAD>
<TITLE>Trouble under MS-DOS</TITLE>
<META HTTP-EQUIV="content-type" CONTENT="text/html; charset=iso-8859-1">
</HEAD>

<BODY BACKGROUND="spiral.gif" BGCOLOR="#FFFFFF" TEXT="#000000" LINK="#0000FF" VLINK="#990099" ALINK="#FF0000">

<TABLE WIDTH="98%">
<TR><TD WIDTH=60 VALIGN=BOTTOM NOWRAP>
<IMG SRC="transp.gif" ALT="" WIDTH=60 HEIGHT=20>
</TD><TD>

<!-- Ab hier Seitentext: -->

<P><BIG>
<BR>
<STRONG><U>IV.2 Trouble under MS-DOS</U></STRONG>
</BIG></P>

<P><BIG>
These are problems that are specific to DOS-based host platforms, including
Windows <NOBR>3.1x</NOBR>. Most of it also applies to Windows 9x systems.
</BIG></P>

<P><BIG>
<OL TYPE=1>
<LI>When initializing the serial port, the DOS <STRONG>MODE</STRONG> utility aborts
    with an error message like: &quot;function not supported on this
    computer&quot;, or &quot;invalid parameter&quot;, or something like that.<BR>
    On most PCs, the BIOS doesn't support baudrates greater than 9600 Baud.
    <STRONG>MODE</STRONG> itself doesn't support baudrates greater than 19200 Baud.
    However, most terminal emulation programs can operate at baudrates of up
    to 115200 Baud.<BR>&nbsp;</LI>
<LI>The <STRONG>RESET51</STRONG> program aborts with &quot;port not found&quot;.<BR>
    The PC-BIOS didn't recognize the printer or serial port specified.<BR>
    Try another port or check your PC hardware.<BR>&nbsp;</LI>
<LI>The <STRONG>RESET51</STRONG> program aborts with &quot;hardware failure&quot;.<BR>
    The PC-BIOS has recognized the specified port, but the data latch
    (printer port) or modem control register (serial port) doesn't work.<BR>
    Try another port, or check the defective port.<BR>&nbsp;</LI>
<LI>The PC hangs when data are sent over the serial interface in batch mode.<BR>
    The RS-232 cable may be plugged into the wrong COM-port.<BR>
    First of all, try the other ports.<BR>
    There may also something be wrong with the modem control signals.<BR>
    (See chapter <A HREF="bcables.htm">II.3 Tailoring the Cables</A>.)<BR>
    &nbsp;</LI>
<LI>It works in interactive mode, but the PC hangs, if data are sent in batch
    mode.<BR>
    There <STRONG><EM>is</EM></STRONG> something wrong with the modem control lines!<BR>
    Employ the <NOBR>BOOT-51</NOBR> User's Manual and check the RS-232 cable
    at the PC side connector.<BR>&nbsp;</LI>
<LI>When invoked, the <NOBR>MS-DOS</NOBR> <STRONG>MODE</STRONG> command hangs, or fails
    to change the previous baudrate, although it terminates without error.<BR>
    Remove all networking and communication drivers and TSR programs from
    your <NOBR><EM>CONFIG.SYS</EM></NOBR> and <NOBR><EM>AUTOEXEC.BAT</EM></NOBR>
    files, reboot, and try it again. There is plenty of quick'n dirty
    software, doing something strange with the BIOS interrupts!</LI>
</OL>
</BIG></P>

<!-- Seitentext Ende -->

<P>
<BR>
<BR>
<CENTER>
<TABLE WIDTH="70%">
<TR><TH><A HREF="boot51.htm"><IMG SRC="home.gif" ALT="[contents]" BORDER=0 WIDTH=32 HEIGHT=32></A></TH>
    <TH><A HREF="btrouble.htm"><IMG SRC="up.gif" ALT="[up]" BORDER=0 WIDTH=32 HEIGHT=32></A></TH>
    <TH><A HREF="bgeneral.htm"><IMG SRC="back.gif" ALT="[back]" BORDER=0 WIDTH=32 HEIGHT=32></A></TH>
    <TH><A HREF="blinux.htm"><IMG SRC="next.gif" ALT="[next]" BORDER=0 WIDTH=32 HEIGHT=32></A></TH>
</TR>
</TABLE>
</CENTER>
</P>

</TD></TR>
</TABLE>

</BODY>

</HTML>
⌨️ 快捷键说明

复制代码 Ctrl + C
搜索代码 Ctrl + F
全屏模式 F11
切换主题 Ctrl + Shift + D
显示快捷键 ?
增大字号 Ctrl + =
减小字号 Ctrl + -