sacsng.c

u-boot-1.1.6 源码包

/*
 * (C) Copyright 2002
 * Custom IDEAS, Inc. <www.cideas.com>
 * Gerald Van Baren <[e-mail]>
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

#include <asm/u-boot.h>
#include <common.h>
#include <ioports.h>
#include <mpc8260.h>
#include <i2c.h>
#include <spi.h>
#include <command.h>

#ifdef CONFIG_SHOW_BOOT_PROGRESS
#include <status_led.h>
#endif

#ifdef CONFIG_ETHER_LOOPBACK_TEST
extern void eth_loopback_test(void);
#endif /* CONFIG_ETHER_LOOPBACK_TEST */

extern int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);

#include "clkinit.h"
#include "ioconfig.h" /* I/O configuration table */

/*
 * PBI Page Based Interleaving
 *   PSDMR_PBI page based interleaving
 *   0         bank based interleaving
 * External Address Multiplexing (EAMUX) adds a clock to address cycles
 *   (this can help with marginal board layouts)
 *   PSDMR_EAMUX  adds a clock
 *   0            no extra clock
 * Buffer Command (BUFCMD) adds a clock to command cycles.
 *   PSDMR_BUFCMD adds a clock
 *   0            no extra clock
 */
#define CONFIG_PBI		PSDMR_PBI
#define PESSIMISTIC_SDRAM	0
#define EAMUX			0	/* EST requires EAMUX */
#define BUFCMD			0

/*
 * ADC/DAC Defines:
 */
#define INITIAL_SAMPLE_RATE 10016     /* Initial Daq sample rate */
#define INITIAL_RIGHT_JUST  0         /* Initial DAC right justification */
#define INITIAL_MCLK_DIVIDE 0         /* Initial MCLK Divide */
#define INITIAL_SAMPLE_64X  1         /* Initial  64x clocking mode */
#define INITIAL_SAMPLE_128X 0         /* Initial 128x clocking mode */

/*
 * ADC Defines:
 */
#define I2C_ADC_1_ADDR 0x0E           /* I2C Address of the ADC #1 */
#define I2C_ADC_2_ADDR 0x0F           /* I2C Address of the ADC #2 */

#define ADC_SDATA1_MASK 0x00020000    /* PA14 - CH12SDATA_PU   */
#define ADC_SDATA2_MASK 0x00010000    /* PA15 - CH34SDATA_PU   */

#define ADC_VREF_CAP   100            /* VREF capacitor in uF */
#define ADC_INITIAL_DELAY (10 * ADC_VREF_CAP) /* 10 usec per uF, in usec */
#define ADC_SDATA_DELAY    100        /* ADC SDATA release delay in usec */
#define ADC_CAL_DELAY (1000000 / INITIAL_SAMPLE_RATE * 4500)
				      /* Wait at least 4100 LRCLK's */

#define ADC_REG1_FRAME_START    0x80  /* Frame start */
#define ADC_REG1_GROUND_CAL     0x40  /* Ground calibration enable */
#define ADC_REG1_ANA_MOD_PDOWN  0x20  /* Analog modulator section in power down */
#define ADC_REG1_DIG_MOD_PDOWN  0x10  /* Digital modulator section in power down */

#define ADC_REG2_128x           0x80  /* Oversample at 128x */
#define ADC_REG2_CAL            0x40  /* System calibration enable */
#define ADC_REG2_CHANGE_SIGN    0x20  /* Change sign enable */
#define ADC_REG2_LR_DISABLE     0x10  /* Left/Right output disable */
#define ADC_REG2_HIGH_PASS_DIS  0x08  /* High pass filter disable */
#define ADC_REG2_SLAVE_MODE     0x04  /* Slave mode */
#define ADC_REG2_DFS            0x02  /* Digital format select */
#define ADC_REG2_MUTE           0x01  /* Mute */

#define ADC_REG7_ADDR_ENABLE    0x80  /* Address enable */
#define ADC_REG7_PEAK_ENABLE    0x40  /* Peak enable */
#define ADC_REG7_PEAK_UPDATE    0x20  /* Peak update */
#define ADC_REG7_PEAK_FORMAT    0x10  /* Peak display format */
#define ADC_REG7_DIG_FILT_PDOWN 0x04  /* Digital filter power down enable */
#define ADC_REG7_FIR2_IN_EN     0x02  /* External FIR2 input enable */
#define ADC_REG7_PSYCHO_EN      0x01  /* External pyscho filter input enable */

/*
 * DAC Defines:
 */

#define I2C_DAC_ADDR 0x11             /* I2C Address of the DAC */

#define DAC_RST_MASK 0x00008000       /* PA16 - DAC_RST*  */
#define DAC_RESET_DELAY    100        /* DAC reset delay in usec */
#define DAC_INITIAL_DELAY 5000        /* DAC initialization delay in usec */

#define DAC_REG1_AMUTE   0x80         /* Auto-mute */

#define DAC_REG1_LEFT_JUST_24_BIT (0 << 4) /* Fmt 0: Left justified 24 bit  */
#define DAC_REG1_I2S_24_BIT       (1 << 4) /* Fmt 1: I2S up to 24 bit       */
#define DAC_REG1_RIGHT_JUST_16BIT (2 << 4) /* Fmt 2: Right justified 16 bit */
#define DAC_REG1_RIGHT_JUST_24BIT (3 << 4) /* Fmt 3: Right justified 24 bit */
#define DAC_REG1_RIGHT_JUST_20BIT (4 << 4) /* Fmt 4: Right justified 20 bit */
#define DAC_REG1_RIGHT_JUST_18BIT (5 << 4) /* Fmt 5: Right justified 18 bit */

#define DAC_REG1_DEM_NO           (0 << 2) /* No      De-emphasis  */
#define DAC_REG1_DEM_44KHZ        (1 << 2) /* 44.1KHz De-emphasis  */
#define DAC_REG1_DEM_48KHZ        (2 << 2) /* 48KHz   De-emphasis  */
#define DAC_REG1_DEM_32KHZ        (3 << 2) /* 32KHz   De-emphasis  */

#define DAC_REG1_SINGLE 0             /*   4- 50KHz sample rate  */
#define DAC_REG1_DOUBLE 1             /*  50-100KHz sample rate  */
#define DAC_REG1_QUAD   2             /* 100-200KHz sample rate  */
#define DAC_REG1_DSD    3             /* Direct Stream Data, DSD */

#define DAC_REG5_INVERT_A   0x80      /* Invert channel A */
#define DAC_REG5_INVERT_B   0x40      /* Invert channel B */
#define DAC_REG5_I2C_MODE   0x20      /* Control port (I2C) mode */
#define DAC_REG5_POWER_DOWN 0x10      /* Power down mode */
#define DAC_REG5_MUTEC_A_B  0x08      /* Mutec A=B */
#define DAC_REG5_FREEZE     0x04      /* Freeze */
#define DAC_REG5_MCLK_DIV   0x02      /* MCLK divide by 2 */
#define DAC_REG5_RESERVED   0x01      /* Reserved */

/* ------------------------------------------------------------------------- */

/*
 * Check Board Identity:
 */

int checkboard(void)
{
    printf ("SACSng\n");

    return 0;
}

/* ------------------------------------------------------------------------- */

long int initdram(int board_type)
{
    volatile immap_t *immap  = (immap_t *)CFG_IMMR;
    volatile memctl8260_t *memctl = &immap->im_memctl;
    volatile uchar c = 0;
    volatile uchar *ramaddr = (uchar *)(CFG_SDRAM_BASE + 0x8);
    uint  psdmr = CFG_PSDMR;
    int   i;
    uint   psrt = 14;					/* for no SPD */
    uint   chipselects = 1;				/* for no SPD */
    uint   sdram_size = CFG_SDRAM0_SIZE * 1024 * 1024;	/* for no SPD */
    uint   or = CFG_OR2_PRELIM;				/* for no SPD */
#ifdef SDRAM_SPD_ADDR
    uint   data_width;
    uint   rows;
    uint   banks;
    uint   cols;
    uint   caslatency;
    uint   width;
    uint   rowst;
    uint   sdam;
    uint   bsma;
    uint   sda10;
    u_char spd_size;
    u_char data;
    u_char cksum;
    int    j;
#endif

#ifdef SDRAM_SPD_ADDR
    /* Keep the compiler from complaining about potentially uninitialized vars */
    data_width = chipselects = rows = banks = cols = caslatency = psrt = 0;

    /*
     * Read the SDRAM SPD EEPROM via I2C.
     */
    i2c_read(SDRAM_SPD_ADDR, 0, 1, &data, 1);
    spd_size = data;
    cksum    = data;
    for(j = 1; j < 64; j++) {	/* read only the checksummed bytes */
	/* note: the I2C address autoincrements when alen == 0 */
	i2c_read(SDRAM_SPD_ADDR, 0, 0, &data, 1);
	     if(j ==  5) chipselects = data & 0x0F;
	else if(j ==  6) data_width  = data;
	else if(j ==  7) data_width |= data << 8;
	else if(j ==  3) rows        = data & 0x0F;
	else if(j ==  4) cols        = data & 0x0F;
	else if(j == 12) {
	    /*
	     * Refresh rate: this assumes the prescaler is set to
	     * approximately 1uSec per tick.
	     */
	    switch(data & 0x7F) {
		default:
		case 0:  psrt =  14 ; /*  15.625uS */  break;
		case 1:  psrt =   2;  /*   3.9uS   */  break;
		case 2:  psrt =   6;  /*   7.8uS   */  break;
		case 3:  psrt =  29;  /*  31.3uS   */  break;
		case 4:  psrt =  60;  /*  62.5uS   */  break;
		case 5:  psrt = 120;  /* 125uS     */  break;
	    }
	}
	else if(j == 17) banks       = data;
	else if(j == 18) {
	    caslatency = 3; /* default CL */
#if(PESSIMISTIC_SDRAM)
		 if((data & 0x04) != 0) caslatency = 3;
	    else if((data & 0x02) != 0) caslatency = 2;
	    else if((data & 0x01) != 0) caslatency = 1;
#else
		 if((data & 0x01) != 0) caslatency = 1;
	    else if((data & 0x02) != 0) caslatency = 2;
	    else if((data & 0x04) != 0) caslatency = 3;
#endif
	    else {
		printf ("WARNING: Unknown CAS latency 0x%02X, using 3\n",
			data);
	    }
	}
	else if(j == 63) {
	    if(data != cksum) {
		printf ("WARNING: Configuration data checksum failure:"
			" is 0x%02x, calculated 0x%02x\n",
			data, cksum);
	    }
	}
	cksum += data;
    }

    /* We don't trust CL less than 2 (only saw it on an old 16MByte DIMM) */
    if(caslatency < 2) {
	printf("WARNING: CL was %d, forcing to 2\n", caslatency);
	caslatency = 2;
    }
    if(rows > 14) {
	printf("WARNING: This doesn't look good, rows = %d, should be <= 14\n", rows);
	rows = 14;
    }
    if(cols > 11) {
	printf("WARNING: This doesn't look good, columns = %d, should be <= 11\n", cols);
	cols = 11;
    }

    if((data_width != 64) && (data_width != 72))
    {
	printf("WARNING: SDRAM width unsupported, is %d, expected 64 or 72.\n",
	    data_width);
    }
    width = 3;		/* 2^3 = 8 bytes = 64 bits wide */
    /*
     * Convert banks into log2(banks)
     */
    if     (banks == 2)	banks = 1;
    else if(banks == 4)	banks = 2;
    else if(banks == 8)	banks = 3;

    sdram_size = 1 << (rows + cols + banks + width);

#if(CONFIG_PBI == 0)	/* bank-based interleaving */
    rowst = ((32 - 6) - (rows + cols + width)) * 2;
#else
    rowst = 32 - (rows + banks + cols + width);
#endif

    or = ~(sdram_size - 1)    |	/* SDAM address mask	*/
	  ((banks-1) << 13)   |	/* banks per device	*/
	  (rowst << 9)        |	/* rowst		*/
	  ((rows - 9) << 6);	/* numr			*/

    memctl->memc_or2 = or;

    /*
     * SDAM specifies the number of columns that are multiplexed
     * (reference AN2165/D), defined to be (columns - 6) for page
     * interleave, (columns - 8) for bank interleave.
     *
     * BSMA is 14 - max(rows, cols).  The bank select lines come
     * into play above the highest "address" line going into the
     * the SDRAM.
     */
#if(CONFIG_PBI == 0)	/* bank-based interleaving */
    sdam = cols - 8;
    bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols);
    sda10 = sdam + 2;
#else
    sdam = cols - 6;
    bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols);
    sda10 = sdam;
#endif
#if(PESSIMISTIC_SDRAM)
    psdmr = (CONFIG_PBI              |\
	     PSDMR_RFEN              |\
	     PSDMR_RFRC_16_CLK       |\
	     PSDMR_PRETOACT_8W       |\
	     PSDMR_ACTTORW_8W        |\
	     PSDMR_WRC_4C            |\
	     PSDMR_EAMUX             |\
	     PSDMR_BUFCMD)           |\
	     caslatency              |\
	     ((caslatency - 1) << 6) |	/* LDOTOPRE is CL - 1 */ \
	     (sdam << 24)            |\
	     (bsma << 21)            |\
	     (sda10 << 18);
#else
    psdmr = (CONFIG_PBI              |\
	     PSDMR_RFEN              |\
	     PSDMR_RFRC_7_CLK        |\
	     PSDMR_PRETOACT_3W       |	/* 1 for 7E parts (fast PC-133) */ \
	     PSDMR_ACTTORW_2W        |	/* 1 for 7E parts (fast PC-133) */ \
	     PSDMR_WRC_1C            |	/* 1 clock + 7nSec */
	     EAMUX                   |\
	     BUFCMD)                 |\
	     caslatency              |\
	     ((caslatency - 1) << 6) |	/* LDOTOPRE is CL - 1 */ \
	     (sdam << 24)            |\
	     (bsma << 21)            |\
	     (sda10 << 18);
#endif
#endif

    /*
     * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35):
     *
     * "At system reset, initialization software must set up the
     *  programmable parameters in the memory controller banks registers
     *  (ORx, BRx, P/LSDMR). After all memory parameters are configured,
     *  system software should execute the following initialization sequence
     *  for each SDRAM device.
     *
     *  1. Issue a PRECHARGE-ALL-BANKS command
     *  2. Issue eight CBR REFRESH commands
     *  3. Issue a MODE-SET command to initialize the mode register
     *
     * Quote from Micron MT48LC8M16A2 data sheet:
     *
     *  "...the SDRAM requires a 100uS delay prior to issuing any
     *  command other than a COMMAND INHIBIT or NOP.  Starting at some
     *  point during this 100uS period and continuing at least through
     *  the end of this period, COMMAND INHIBIT or NOP commands should
     *  be applied."
     *
     *  "Once the 100uS delay has been satisfied with at least one COMMAND
     *  INHIBIT or NOP command having been applied, a /PRECHARGE command/
     *  should be applied.  All banks must then be precharged, thereby
     *  placing the device in the all banks idle state."
     *
     *  "Once in the idle state, /two/ AUTO REFRESH cycles must be
     *  performed.  After the AUTO REFRESH cycles are complete, the
     *  SDRAM is ready for mode register programming."
     *
     *  (/emphasis/ mine, gvb)
     *
     *  The way I interpret this, Micron start up sequence is:
     *  1. Issue a PRECHARGE-BANK command (initial precharge)
     *  2. Issue a PRECHARGE-ALL-BANKS command ("all banks ... precharged")
     *  3. Issue two (presumably, doing eight is OK) CBR REFRESH commands
     *  4. Issue a MODE-SET command to initialize the mode register
     *
     *  --------
     *
     *  The initial commands are executed by setting P/LSDMR[OP] and
     *  accessing the SDRAM with a single-byte transaction."
     *
     * The appropriate BRx/ORx registers have already been set when we
     * get here. The SDRAM can be accessed at the address CFG_SDRAM_BASE.
     */

    memctl->memc_mptpr = CFG_MPTPR;
    memctl->memc_psrt  = psrt;

    memctl->memc_psdmr = psdmr | PSDMR_OP_PREA;
    *ramaddr = c;

    memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR;
    for (i = 0; i < 8; i++)
	*ramaddr = c;

    memctl->memc_psdmr = psdmr | PSDMR_OP_MRW;
    *ramaddr = c;

    memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN;
    *ramaddr = c;

    /*
     * Do it a second time for the second set of chips if the DIMM has
     * two chip selects (double sided).
     */
    if(chipselects > 1) {
	ramaddr += sdram_size;

	memctl->memc_br3 = CFG_BR3_PRELIM + sdram_size;
	memctl->memc_or3 = or;

	memctl->memc_psdmr = psdmr | PSDMR_OP_PREA;
	*ramaddr = c;

	memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR;
	for (i = 0; i < 8; i++)
	    *ramaddr = c;

	memctl->memc_psdmr = psdmr | PSDMR_OP_MRW;
	*ramaddr = c;

	memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN;
	*ramaddr = c;
    }

    /* return total ram size */
    return (sdram_size * chipselects);
}

/*-----------------------------------------------------------------------
 * Board Control Functions
 */
void board_poweroff (void)
{
    while (1);		/* hang forever */
}


#ifdef CONFIG_MISC_INIT_R
/* ------------------------------------------------------------------------- */
int misc_init_r(void)
{
    /*