scarderr.h

vc6.0完整版

/*
 scarderr.mc

   Error message codes from the Smart Card Resource Manager
   These messages must be reconciled with winerror.w

   30-Jun-97 - DBarlow Created.  */
#ifndef SCARD_S_SUCCESS
//
// =============================
// Facility SCARD Error Messages
// =============================
//
#define SCARD_S_SUCCESS NO_ERROR
//
//  Values are 32 bit values layed out as follows:
//
//   3 3 2 2 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1
//   1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0
//  +---+-+-+-----------------------+-------------------------------+
//  |Sev|C|R|     Facility          |               Code            |
//  +---+-+-+-----------------------+-------------------------------+
//
//  where
//
//      Sev - is the severity code
//
//          00 - Success
//          01 - Informational
//          10 - Warning
//          11 - Error
//
//      C - is the Customer code flag
//
//      R - is a reserved bit
//
//      Facility - is the facility code
//
//      Code - is the facility's status code
//
//
// Define the facility codes
//
#define FACILITY_SYSTEM                  0x0
#define FACILITY_SCARD                   0x10


//
// Define the severity codes
//


//
// MessageId: SCARD_F_INTERNAL_ERROR
//
// MessageText:
//
//  An internal consistency check failed
//
#define SCARD_F_INTERNAL_ERROR           ((DWORD)0x80100001L)

//
// MessageId: SCARD_E_CANCELLED
//
// MessageText:
//
//  The action was cancelled by an SCardCancel request
//
#define SCARD_E_CANCELLED                ((DWORD)0x80100002L)

//
// MessageId: SCARD_E_INVALID_HANDLE
//
// MessageText:
//
//  The supplied handle was invalid
//
#define SCARD_E_INVALID_HANDLE           ((DWORD)0x80100003L)

//
// MessageId: SCARD_E_INVALID_PARAMETER
//
// MessageText:
//
//  One or more of the supplied parameters could not be properly interpreted
//
#define SCARD_E_INVALID_PARAMETER        ((DWORD)0x80100004L)

//
// MessageId: SCARD_E_INVALID_TARGET
//
// MessageText:
//
//  Registry startup information is missing or invalid
//
#define SCARD_E_INVALID_TARGET           ((DWORD)0x80100005L)

//
// MessageId: SCARD_E_NO_MEMORY
//
// MessageText:
//
//  Not enough memory available to complete this command
//
#define SCARD_E_NO_MEMORY                ((DWORD)0x80100006L)

//
// MessageId: SCARD_F_WAITED_TOO_LONG
//
// MessageText:
//
//  An internal consistency timer has expired
//
#define SCARD_F_WAITED_TOO_LONG          ((DWORD)0x80100007L)

//
// MessageId: SCARD_E_INSUFFICIENT_BUFFER
//
// MessageText:
//
//  The data buffer to receive returned data is too small for the returned data
//
#define SCARD_E_INSUFFICIENT_BUFFER      ((DWORD)0x80100008L)

//
// MessageId: SCARD_E_UNKNOWN_READER
//
// MessageText:
//
//  The specified reader name is not recognized
//
#define SCARD_E_UNKNOWN_READER           ((DWORD)0x80100009L)

//
// MessageId: SCARD_E_TIMEOUT
//
// MessageText:
//
//  The user-specified timeout value has expired
//
#define SCARD_E_TIMEOUT                  ((DWORD)0x8010000AL)

//
// MessageId: SCARD_E_SHARING_VIOLATION
//
// MessageText:
//
//  The smart card cannot be accessed because of other connections outstanding
//
#define SCARD_E_SHARING_VIOLATION        ((DWORD)0x8010000BL)

//
// MessageId: SCARD_E_NO_SMARTCARD
//
// MessageText:
//
//  The operation requires a Smart Card, but no Smart Card is currently in the device
//
#define SCARD_E_NO_SMARTCARD             ((DWORD)0x8010000CL)

//
// MessageId: SCARD_E_UNKNOWN_CARD
//
// MessageText:
//
//  The specified smart card name is not recognized
//
#define SCARD_E_UNKNOWN_CARD             ((DWORD)0x8010000DL)

//
// MessageId: SCARD_E_CANT_DISPOSE
//
// MessageText:
//
//  The system could not dispose of the media in the requested manner
//
#define SCARD_E_CANT_DISPOSE             ((DWORD)0x8010000EL)

//
// MessageId: SCARD_E_PROTO_MISMATCH
//
// MessageText:
//
//  The requested protocols are incompatible with the protocol currently in use with the smart card
//
#define SCARD_E_PROTO_MISMATCH           ((DWORD)0x8010000FL)

//
// MessageId: SCARD_E_NOT_READY
//
// MessageText:
//
//  The reader or smart card is not ready to accept commands
//
#define SCARD_E_NOT_READY                ((DWORD)0x80100010L)

//
// MessageId: SCARD_E_INVALID_VALUE
//
// MessageText:
//
//  One or more of the supplied parameters values could not be properly interpreted
//
#define SCARD_E_INVALID_VALUE            ((DWORD)0x80100011L)

//
// MessageId: SCARD_E_SYSTEM_CANCELLED
//
// MessageText:
//
//  The action was cancelled by the system, presumably to log off or shut down
//
#define SCARD_E_SYSTEM_CANCELLED         ((DWORD)0x80100012L)

//
// MessageId: SCARD_F_COMM_ERROR
//
// MessageText:
//
//  An internal communications error has been detected
//
#define SCARD_F_COMM_ERROR               ((DWORD)0x80100013L)

//
// MessageId: SCARD_F_UNKNOWN_ERROR
//
// MessageText:
//
//  An internal error has been detected, but the source is unknown
//
#define SCARD_F_UNKNOWN_ERROR            ((DWORD)0x80100014L)

//
// MessageId: SCARD_E_INVALID_ATR
//
// MessageText:
//
//  An ATR obtained from the registry is not a valid ATR string
//
#define SCARD_E_INVALID_ATR              ((DWORD)0x80100015L)

//
// MessageId: SCARD_E_NOT_TRANSACTED
//
// MessageText:
//
//  An attempt was made to end a non-existent transaction
//
#define SCARD_E_NOT_TRANSACTED           ((DWORD)0x80100016L)

//
// MessageId: SCARD_E_READER_UNAVAILABLE
//
// MessageText:
//
//  The specified reader is not currently available for use
//
#define SCARD_E_READER_UNAVAILABLE       ((DWORD)0x80100017L)

//
// MessageId: SCARD_P_SHUTDOWN
//
// MessageText:
//
//  PRIVATE -- Internal flag to force server termination
//
#define SCARD_P_SHUTDOWN                 ((DWORD)0x80100018L)

//
// MessageId: SCARD_E_PCI_TOO_SMALL
//
// MessageText:
//
//  The PCI Receive buffer was too small
//
#define SCARD_E_PCI_TOO_SMALL            ((DWORD)0x80100019L)

//
// MessageId: SCARD_E_READER_UNSUPPORTED
//
// MessageText:
//
//  The reader driver does not meet minimal requirements for support
//
#define SCARD_E_READER_UNSUPPORTED       ((DWORD)0x8010001AL)

//
// MessageId: SCARD_E_DUPLICATE_READER
//
// MessageText:
//
//  The reader driver did not produce a unique reader name
//
#define SCARD_E_DUPLICATE_READER         ((DWORD)0x8010001BL)

//
// MessageId: SCARD_E_CARD_UNSUPPORTED
//
// MessageText:
//
//  The smart card does not meet minimal requirements for support
//
#define SCARD_E_CARD_UNSUPPORTED         ((DWORD)0x8010001CL)

//
// MessageId: SCARD_E_NO_SERVICE
//
// MessageText:
//
//  The Smart card resource manager is not running
//
#define SCARD_E_NO_SERVICE               ((DWORD)0x8010001DL)

//
// MessageId: SCARD_E_SERVICE_STOPPED
//
// MessageText:
//
//  The Smart card resource manager has shut down
//
#define SCARD_E_SERVICE_STOPPED          ((DWORD)0x8010001EL)

//
// These are resettable warning codes.
//
//
// MessageId: SCARD_W_UNSUPPORTED_CARD
//
// MessageText:
//
//  The reader cannot communicate with the smart card, due to ATR configuration conflicts
//
#define SCARD_W_UNSUPPORTED_CARD         ((DWORD)0x80100065L)

//
// MessageId: SCARD_W_UNRESPONSIVE_CARD
//
// MessageText:
//
//  The smart card is not responding to a reset
//
#define SCARD_W_UNRESPONSIVE_CARD        ((DWORD)0x80100066L)

//
// MessageId: SCARD_W_UNPOWERED_CARD
//
// MessageText:
//
//  Power has been removed from the smart card, so that further communication is not possible
//
#define SCARD_W_UNPOWERED_CARD           ((DWORD)0x80100067L)

//
// MessageId: SCARD_W_RESET_CARD
//
// MessageText:
//
//  The smart card has been reset, so any shared state information is invalid
//
#define SCARD_W_RESET_CARD               ((DWORD)0x80100068L)

//
// MessageId: SCARD_W_REMOVED_CARD
//
// MessageText:
//
//  The smart card has been removed, so that further communication is not possible
//
#define SCARD_W_REMOVED_CARD             ((DWORD)0x80100069L)

#endif // SCARD_S_SUCCESS