pwm.pdb

利用PWM产生高精度正弦波,从PWM引脚输出的脉冲信号经过简单的低通滤波后,可以得到平滑的正弦波,波的频率可以微调

[DebugState_v1-Debug.AddOn.ST7LoadSaveConfiguration]
RestoreSP_Control=1
[DebugState_v1-Debug.DebugContext]
DumpRWOnFly=0
WatchVariables1=i!0;j!0;
FormatWatch1=0
FormatViewType1=1
FormatViewAddress1=1
WatchRWOnFlyTab1=0
WatchVariables2=
FormatWatch2=0
FormatViewType2=1
FormatViewAddress2=1
WatchRWOnFlyTab2=0
WatchVariables3=
FormatWatch3=0
FormatViewType3=1
FormatViewAddress3=1
WatchRWOnFlyTab3=0
WatchVariables4=
FormatWatch4=0
FormatViewType4=1
FormatViewAddress4=1
WatchRWOnFlyTab4=0
FormatLocals=0
FormatParameters=0
[DebugState_v1-Debug.AddOn.St7Watchpoint]
NbDataBreakpoint=0
[DebugState_v1-Debug.AddOn.St7HardEvents]
HevtDefType=EVT_ON
NbHardEvent=0
[DebugState_v1-Debug.AddOn]
HevtTraceFiltering=0
HevtTrigInEnab=0
HevtBreakOnTraceOverflowEnable=0
[DebugState_v1-Debug.AddOn.St7Registers]
ActiveTab=1
[DebugState_v1-Debug.AddOn.St7PeripheralRegister]
DisplayFormat=1
ShowPeriphAddress=0
ShowRegisterAddress=1
[DebugState_v1-Debug.AddOn.St7McuOptionsMemMap]
McuName=ST72F561R9
CurrentEmuTypeAndName=DVP3 Emulator
NbMcuOption=12
McuOption0=gdi mcuoption -set FOSC 16MHz
McuOption1=gdi mcuoption -set MCC Frozen when not run
McuOption2=gdi mcuoption -set PWM Free when not run
McuOption3=gdi mcuoption -set TIMER_16 Frozen when not run
McuOption4=gdi mcuoption -set TIMER_8 Frozen when not run
McuOption5=gdi mcuoption -set AFI_MAP_0 TIMER16 ICAP2 on PC1
McuOption6=gdi mcuoption -set AFI_MAP_1 T16 on PB & PC LINSCI on PD
McuOption7=gdi mcuoption -set OSCRANGE HS:16..8MHz
McuOption8=gdi mcuoption -set PLL Disable
McuOption9=gdi mcuoption -set RSTC 256 cpu cycles reset phase
McuOption10=gdi mcuoption -set WDG.HALT No_Reset
McuOption11=gdi mcuoption -set WDG.SW Software
NbRange=19
Range0=mcumap -set [0x0000-0x000b]:"PERIPH (RW)"
Range1=mcumap -set [0x000c-0x0011]:"_PERIPH_RW"
Range2=mcumap -set [0x0012-0x0020]:"NER"
Range3=mcumap -set [0x0021-0x0023]:"PERIPH (RW)"
Range4=mcumap -set [0x0024-0x0024]:"NER"
Range5=mcumap -set [0x0025-0x0039]:"PERIPH (RW)"
Range6=mcumap -set [0x003a-0x003b]:"PERIPH (R)"
Range7=mcumap -set [0x003c-0x0045]:"PERIPH (RW)"
Range8=mcumap -set [0x0046-0x0048]:"PERIPH (R)"
Range9=mcumap -set [0x0049-0x004f]:"PERIPH (RW)"
Range10=mcumap -set [0x0050-0x0050]:"NER"
Range11=mcumap -set [0x0051-0x005f]:"PERIPH (RW)"
Range12=mcumap -set [0x0060-0x0060]:"PERIPH (R)"
Range13=mcumap -set [0x0061-0x007f]:"PERIPH (RW)"
Range14=mcumap -set [0x0080-0x00ff]:"RAM"
Range15=mcumap -set [0x0200-0x087f]:"RAM"
Range16=mcumap -set [0x0880-0x0fff]:"NEM"
Range17=mcumap -set [0x1000-0xffdf]:"ROM"
Range18=mcumap -set [0xffe0-0xffff]:"VECTORS"
[DebugState_v1-Debug.AddOn.St7StackPtrControl]
SP_Ctrl_Enable=
SP_Ctrl_OverFlow=
[DebugState_v1-Debug.AddOn.Trace]
Trace Settings=9;50;60;40;80;240;100;50;50;40;9;0;0;0;0;0;0;0;0;0;4;1;1;1;1;1;1;9;1;2;3;4;5;6;7;8;9;10;-1;0;1;2;3;4;5;6;7;8;
Trace Status=on