fec.c

linux下的BOOT程序原码,有需要的可以来下,保证好用

/*
 * (C) Copyright 2003-2005
 * Wolfgang Denk, DENX Software Engineering, [e-mail].
 *
 * This file is based on mpc4200fec.c,
 * (C) Copyright Motorola, Inc., 2000
 */

#include <common.h>
#include <mpc5xxx.h>
#include <malloc.h>
#include <net.h>
#include <miiphy.h>
#include "sdma.h"
#include "fec.h"

/* #define DEBUG	0x28 */

#if (CONFIG_COMMANDS & CFG_CMD_NET) && defined(CONFIG_NET_MULTI) && \
	defined(CONFIG_MPC5xxx_FEC)

#if !(defined(CONFIG_MII) || (CONFIG_COMMANDS & CFG_CMD_MII))
#error "CONFIG_MII has to be defined!"
#endif

#if (DEBUG & 0x60)
static void tfifo_print(char *devname, mpc5xxx_fec_priv *fec);
static void rfifo_print(char *devname, mpc5xxx_fec_priv *fec);
#endif /* DEBUG */

#if (DEBUG & 0x40)
static uint32 local_crc32(char *string, unsigned int crc_value, int len);
#endif

typedef struct {
    uint8 data[1500];           /* actual data */
    int length;                 /* actual length */
    int used;                   /* buffer in use or not */
    uint8 head[16];             /* MAC header(6 + 6 + 2) + 2(aligned) */
} NBUF;

int fec5xxx_miiphy_read(char *devname, uint8 phyAddr, uint8 regAddr, uint16 * retVal);
int fec5xxx_miiphy_write(char *devname, uint8 phyAddr, uint8 regAddr, uint16 data);

/********************************************************************/
#if (DEBUG & 0x2)
static void mpc5xxx_fec_phydump (char *devname)
{
	uint16 phyStatus, i;
	uint8 phyAddr = CONFIG_PHY_ADDR;
	uint8 reg_mask[] = {
#if CONFIG_PHY_TYPE == 0x79c874	/* AMD Am79C874 */
		/* regs to print: 0...7, 16...19, 21, 23, 24 */
		1, 1, 1, 1,  1, 1, 1, 1,     0, 0, 0, 0,  0, 0, 0, 0,
		1, 1, 1, 1,  0, 1, 0, 1,     1, 0, 0, 0,  0, 0, 0, 0,
#else
		/* regs to print: 0...8, 16...20 */
		1, 1, 1, 1,  1, 1, 1, 1,     1, 0, 0, 0,  0, 0, 0, 0,
		1, 1, 1, 1,  1, 0, 0, 0,     0, 0, 0, 0,  0, 0, 0, 0,
#endif
	};

	for (i = 0; i < 32; i++) {
		if (reg_mask[i]) {
			miiphy_read(devname, phyAddr, i, &phyStatus);
			printf("Mii reg %d: 0x%04x\n", i, phyStatus);
		}
	}
}
#endif

/********************************************************************/
static int mpc5xxx_fec_rbd_init(mpc5xxx_fec_priv *fec)
{
	int ix;
	char *data;
	static int once = 0;

	for (ix = 0; ix < FEC_RBD_NUM; ix++) {
		if (!once) {
			data = (char *)malloc(FEC_MAX_PKT_SIZE);
			if (data == NULL) {
				printf ("RBD INIT FAILED\n");
				return -1;
			}
			fec->rbdBase[ix].dataPointer = (uint32)data;
		}
		fec->rbdBase[ix].status = FEC_RBD_EMPTY;
		fec->rbdBase[ix].dataLength = 0;
	}
	once ++;

	/*
	 * have the last RBD to close the ring
	 */
	fec->rbdBase[ix - 1].status |= FEC_RBD_WRAP;
	fec->rbdIndex = 0;

	return 0;
}

/********************************************************************/
static void mpc5xxx_fec_tbd_init(mpc5xxx_fec_priv *fec)
{
	int ix;

	for (ix = 0; ix < FEC_TBD_NUM; ix++) {
		fec->tbdBase[ix].status = 0;
	}

	/*
	 * Have the last TBD to close the ring
	 */
	fec->tbdBase[ix - 1].status |= FEC_TBD_WRAP;

	/*
	 * Initialize some indices
	 */
	fec->tbdIndex = 0;
	fec->usedTbdIndex = 0;
	fec->cleanTbdNum = FEC_TBD_NUM;
}

/********************************************************************/
static void mpc5xxx_fec_rbd_clean(mpc5xxx_fec_priv *fec, volatile FEC_RBD * pRbd)
{
	/*
	 * Reset buffer descriptor as empty
	 */
	if ((fec->rbdIndex) == (FEC_RBD_NUM - 1))
		pRbd->status = (FEC_RBD_WRAP | FEC_RBD_EMPTY);
	else
		pRbd->status = FEC_RBD_EMPTY;

	pRbd->dataLength = 0;

	/*
	 * Now, we have an empty RxBD, restart the SmartDMA receive task
	 */
	SDMA_TASK_ENABLE(FEC_RECV_TASK_NO);

	/*
	 * Increment BD count
	 */
	fec->rbdIndex = (fec->rbdIndex + 1) % FEC_RBD_NUM;
}

/********************************************************************/
static void mpc5xxx_fec_tbd_scrub(mpc5xxx_fec_priv *fec)
{
	volatile FEC_TBD *pUsedTbd;

#if (DEBUG & 0x1)
	printf ("tbd_scrub: fec->cleanTbdNum = %d, fec->usedTbdIndex = %d\n",
		fec->cleanTbdNum, fec->usedTbdIndex);
#endif

	/*
	 * process all the consumed TBDs
	 */
	while (fec->cleanTbdNum < FEC_TBD_NUM) {
		pUsedTbd = &fec->tbdBase[fec->usedTbdIndex];
		if (pUsedTbd->status & FEC_TBD_READY) {
#if (DEBUG & 0x20)
			printf("Cannot clean TBD %d, in use\n", fec->cleanTbdNum);
#endif
			return;
		}

		/*
		 * clean this buffer descriptor
		 */
		if (fec->usedTbdIndex == (FEC_TBD_NUM - 1))
			pUsedTbd->status = FEC_TBD_WRAP;
		else
			pUsedTbd->status = 0;

		/*
		 * update some indeces for a correct handling of the TBD ring
		 */
		fec->cleanTbdNum++;
		fec->usedTbdIndex = (fec->usedTbdIndex + 1) % FEC_TBD_NUM;
	}
}

/********************************************************************/
static void mpc5xxx_fec_set_hwaddr(mpc5xxx_fec_priv *fec, char *mac)
{
	uint8 currByte;			/* byte for which to compute the CRC */
	int byte;			/* loop - counter */
	int bit;			/* loop - counter */
	uint32 crc = 0xffffffff;	/* initial value */

	/*
	 * The algorithm used is the following:
	 * we loop on each of the six bytes of the provided address,
	 * and we compute the CRC by left-shifting the previous
	 * value by one position, so that each bit in the current
	 * byte of the address may contribute the calculation. If
	 * the latter and the MSB in the CRC are different, then
	 * the CRC value so computed is also ex-ored with the
	 * "polynomium generator". The current byte of the address
	 * is also shifted right by one bit at each iteration.
	 * This is because the CRC generatore in hardware is implemented
	 * as a shift-register with as many ex-ores as the radixes
	 * in the polynomium. This suggests that we represent the
	 * polynomiumm itself as a 32-bit constant.
	 */
	for (byte = 0; byte < 6; byte++) {
		currByte = mac[byte];
		for (bit = 0; bit < 8; bit++) {
			if ((currByte & 0x01) ^ (crc & 0x01)) {
				crc >>= 1;
				crc = crc ^ 0xedb88320;
			} else {
				crc >>= 1;
			}
			currByte >>= 1;
		}
	}

	crc = crc >> 26;

	/*
	 * Set individual hash table register
	 */
	if (crc >= 32) {
		fec->eth->iaddr1 = (1 << (crc - 32));
		fec->eth->iaddr2 = 0;
	} else {
		fec->eth->iaddr1 = 0;
		fec->eth->iaddr2 = (1 << crc);
	}

	/*
	 * Set physical address
	 */
	fec->eth->paddr1 = (mac[0] << 24) + (mac[1] << 16) + (mac[2] << 8) + mac[3];
	fec->eth->paddr2 = (mac[4] << 24) + (mac[5] << 16) + 0x8808;
}

/********************************************************************/
static int mpc5xxx_fec_init(struct eth_device *dev, bd_t * bis)
{
	DECLARE_GLOBAL_DATA_PTR;
	mpc5xxx_fec_priv *fec = (mpc5xxx_fec_priv *)dev->priv;
	struct mpc5xxx_sdma *sdma = (struct mpc5xxx_sdma *)MPC5XXX_SDMA;

#if (DEBUG & 0x1)
	printf ("mpc5xxx_fec_init... Begin\n");
#endif

	/*
	 * Initialize RxBD/TxBD rings
	 */
	mpc5xxx_fec_rbd_init(fec);
	mpc5xxx_fec_tbd_init(fec);

	/*
	 * Clear FEC-Lite interrupt event register(IEVENT)
	 */
	fec->eth->ievent = 0xffffffff;

	/*
	 * Set interrupt mask register
	 */
	fec->eth->imask = 0x00000000;

	/*
	 * Set FEC-Lite receive control register(R_CNTRL):
	 */
	if (fec->xcv_type == SEVENWIRE) {
		/*
		 * Frame length=1518; 7-wire mode
		 */
		fec->eth->r_cntrl = 0x05ee0020;	/*0x05ee0000;FIXME */
	} else {
		/*
		 * Frame length=1518; MII mode;
		 */
		fec->eth->r_cntrl = 0x05ee0024;	/*0x05ee0004;FIXME */
	}

	fec->eth->x_cntrl = 0x00000000;	/* half-duplex, heartbeat disabled */
	if (fec->xcv_type != SEVENWIRE) {
		/*
		 * Set MII_SPEED = (1/(mii_speed * 2)) * System Clock
		 * and do not drop the Preamble.
		 */
		fec->eth->mii_speed = (((gd->ipb_clk >> 20) / 5) << 1);	/* No MII for 7-wire mode */
	}

	/*
	 * Set Opcode/Pause Duration Register
	 */
	fec->eth->op_pause = 0x00010020;	/*FIXME0xffff0020; */

	/*
	 * Set Rx FIFO alarm and granularity value
	 */
	fec->eth->rfifo_cntrl = 0x0c000000
				| (fec->eth->rfifo_cntrl & ~0x0f000000);
	fec->eth->rfifo_alarm = 0x0000030c;
#if (DEBUG & 0x22)
	if (fec->eth->rfifo_status & 0x00700000 ) {
		printf("mpc5xxx_fec_init() RFIFO error\n");
	}
#endif

	/*
	 * Set Tx FIFO granularity value
	 */
	fec->eth->tfifo_cntrl = 0x0c000000
				| (fec->eth->tfifo_cntrl & ~0x0f000000);
#if (DEBUG & 0x2)
	printf("tfifo_status: 0x%08x\n", fec->eth->tfifo_status);
	printf("tfifo_alarm: 0x%08x\n", fec->eth->tfifo_alarm);
#endif

	/*
	 * Set transmit fifo watermark register(X_WMRK), default = 64
	 */
	fec->eth->tfifo_alarm = 0x00000080;
	fec->eth->x_wmrk = 0x2;

	/*
	 * Set individual address filter for unicast address
	 * and set physical address registers.
	 */
	mpc5xxx_fec_set_hwaddr(fec, (char *)dev->enetaddr);

	/*
	 * Set multicast address filter
	 */
	fec->eth->gaddr1 = 0x00000000;
	fec->eth->gaddr2 = 0x00000000;

	/*
	 * Turn ON cheater FSM: ????
	 */
	fec->eth->xmit_fsm = 0x03000000;

#if defined(CONFIG_MPC5200)
	/*
	 * Turn off COMM bus prefetch in the MGT5200 BestComm. It doesn't
	 * work w/ the current receive task.
	 */
	 sdma->PtdCntrl |= 0x00000001;
#endif

	/*
	 * Set priority of different initiators
	 */
	sdma->IPR0 = 7;		/* always */
	sdma->IPR3 = 6;		/* Eth RX */
	sdma->IPR4 = 5;		/* Eth Tx */

	/*
	 * Clear SmartDMA task interrupt pending bits
	 */
	SDMA_CLEAR_IEVENT(FEC_RECV_TASK_NO);

	/*
	 * Initialize SmartDMA parameters stored in SRAM
	 */
	*(volatile int *)FEC_TBD_BASE = (int)fec->tbdBase;
	*(volatile int *)FEC_RBD_BASE = (int)fec->rbdBase;
	*(volatile int *)FEC_TBD_NEXT = (int)fec->tbdBase;
	*(volatile int *)FEC_RBD_NEXT = (int)fec->rbdBase;

	/*
	 * Enable FEC-Lite controller
	 */
	fec->eth->ecntrl |= 0x00000006;

#if (DEBUG & 0x2)
	if (fec->xcv_type != SEVENWIRE)
		mpc5xxx_fec_phydump ();
#endif

	/*
	 * Enable SmartDMA receive task
	 */
	SDMA_TASK_ENABLE(FEC_RECV_TASK_NO);

#if (DEBUG & 0x1)
	printf("mpc5xxx_fec_init... Done \n");
#endif

	return 1;
}

/********************************************************************/
static int mpc5xxx_fec_init_phy(struct eth_device *dev, bd_t * bis)
{
	DECLARE_GLOBAL_DATA_PTR;
	mpc5xxx_fec_priv *fec = (mpc5xxx_fec_priv *)dev->priv;
	const uint8 phyAddr = CONFIG_PHY_ADDR;	/* Only one PHY */

#if (DEBUG & 0x1)
	printf ("mpc5xxx_fec_init_phy... Begin\n");
#endif

	/*
	 * Initialize GPIO pins
	 */
	if (fec->xcv_type == SEVENWIRE) {
		/*  10MBit with 7-wire operation */
#if defined(CONFIG_TOTAL5200)
		/* 7-wire and USB2 on Ethernet */
		*(vu_long *)MPC5XXX_GPS_PORT_CONFIG |= 0x00030000;
#else	/* !CONFIG_TOTAL5200 */
		/* 7-wire only */
		*(vu_long *)MPC5XXX_GPS_PORT_CONFIG |= 0x00020000;
#endif	/* CONFIG_TOTAL5200 */
	} else {
		/* 100MBit with MD operation */
		*(vu_long *)MPC5XXX_GPS_PORT_CONFIG |= 0x00050000;
	}

	/*
	 * Clear FEC-Lite interrupt event register(IEVENT)
	 */
	fec->eth->ievent = 0xffffffff;

	/*
	 * Set interrupt mask register
	 */
	fec->eth->imask = 0x00000000;

	if (fec->xcv_type != SEVENWIRE) {
		/*
		 * Set MII_SPEED = (1/(mii_speed * 2)) * System Clock
		 * and do not drop the Preamble.
		 */
		fec->eth->mii_speed = (((gd->ipb_clk >> 20) / 5) << 1);	/* No MII for 7-wire mode */
	}

	if (fec->xcv_type != SEVENWIRE) {
		/*
		 * Initialize PHY(LXT971A):
		 *
		 *   Generally, on power up, the LXT971A reads its configuration
		 *   pins to check for forced operation, If not cofigured for
		 *   forced operation, it uses auto-negotiation/parallel detection
		 *   to automatically determine line operating conditions.
		 *   If the PHY device on the other side of the link supports
		 *   auto-negotiation, the LXT971A auto-negotiates with it
		 *   using Fast Link Pulse(FLP) Bursts. If the PHY partner does not
		 *   support auto-negotiation, the LXT971A automatically detects
		 *   the presence of either link pulses(10Mbps PHY) or Idle
		 *   symbols(100Mbps) and sets its operating conditions accordingly.
		 *
		 *   When auto-negotiation is controlled by software, the following
		 *   steps are recommended.
		 *
		 * Note:
		 *   The physical address is dependent on hardware configuration.
		 *
		 */
		int timeout = 1;
		uint16 phyStatus;

		/*
		 * Reset PHY, then delay 300ns
		 */
		miiphy_write(dev->name, phyAddr, 0x0, 0x8000);
		udelay(1000);

		if (fec->xcv_type == MII10) {
			/*
			 * Force 10Base-T, FDX operation
			 */
#if (DEBUG & 0x2)
			printf("Forcing 10 Mbps ethernet link... ");
#endif
			miiphy_read(dev->name, phyAddr, 0x1, &phyStatus);
			/*
			miiphy_write(dev->name, fec, phyAddr, 0x0, 0x0100);
			*/
			miiphy_write(dev->name, phyAddr, 0x0, 0x0180);

			timeout = 20;
			do {	/* wait for link status to go down */
				udelay(10000);
				if ((timeout--) == 0) {
#if (DEBUG & 0x2)
					printf("hmmm, should not have waited...");
#endif
					break;
				}
				miiphy_read(dev->name, phyAddr, 0x1, &phyStatus);
#if (DEBUG & 0x2)
				printf("=");
#endif
			} while ((phyStatus & 0x0004));	/* !link up */

			timeout = 1000;
			do {	/* wait for link status to come back up */
				udelay(10000);
				if ((timeout--) == 0) {
					printf("failed. Link is down.\n");
					break;
				}
				miiphy_read(dev->name, phyAddr, 0x1, &phyStatus);
#if (DEBUG & 0x2)
				printf("+");
#endif
			} while (!(phyStatus & 0x0004));	/* !link up */

#if (DEBUG & 0x2)
			printf ("done.\n");
#endif
		} else {	/* MII100 */
			/*
			 * Set the auto-negotiation advertisement register bits
			 */
			miiphy_write(dev->name, phyAddr, 0x4, 0x01e1);

			/*
			 * Set MDIO bit 0.12 = 1(&& bit 0.9=1?) to enable auto-negotiation
			 */