ds18x20.h

基于AVR ATmega32 单片机的DS1820驱动程序 基于winavr 平台编译

#ifndef DS18X20_H_
#define DS18X20_H_

#include <stdlib.h>
#include <inttypes.h>

// enable DS18x20 EERPROM support
#define DS18X20_EEPROMSUPPORT

// enable extended output via UART by defining:
#define DS18X20_VERBOSE

/* return values */
#define DS18X20_OK          0x00
#define DS18X20_ERROR       0x01
#define DS18X20_START_FAIL  0x02
#define DS18X20_ERROR_CRC   0x03

#define DS18X20_POWER_PARASITE 0x00
#define DS18X20_POWER_EXTERN   0x01

/* DS18X20 specific values (see datasheet) */
#define DS18S20_ID 0x10
#define DS18B20_ID 0x28

#define DS18X20_CONVERT_T	0x44
#define DS18X20_READ		0xBE
#define DS18X20_WRITE		0x4E
#define DS18X20_EE_WRITE	0x48
#define DS18X20_EE_RECALL	0xB8
#define DS18X20_READ_POWER_SUPPLY 0xB4

#define DS18B20_CONF_REG    4
#define DS18B20_9_BIT       0
#define DS18B20_10_BIT      (1<<5)
#define DS18B20_11_BIT      (1<<6)
#define DS18B20_12_BIT      ((1<<6)|(1<<5))

// indefined bits in LSB if 18B20 != 12bit
#define DS18B20_9_BIT_UNDF       ((1<<0)|(1<<1)|(1<<2))
#define DS18B20_10_BIT_UNDF      ((1<<0)|(1<<1))
#define DS18B20_11_BIT_UNDF      ((1<<0))
#define DS18B20_12_BIT_UNDF      0

// conversion times in ms
#define DS18B20_TCONV_12BIT      750
#define DS18B20_TCONV_11BIT      DS18B20_TCONV_12_BIT/2
#define DS18B20_TCONV_10BIT      DS18B20_TCONV_12_BIT/4
#define DS18B20_TCONV_9BIT       DS18B20_TCONV_12_BIT/8
#define DS18S20_TCONV            DS18B20_TCONV_12_BIT

// constant to convert the fraction bits to cel*(10^-4)
#define DS18X20_FRACCONV         625

#define DS18X20_SP_SIZE  9

// DS18X20 EEPROM-Support
#define DS18X20_WRITE_SCRATCHPAD  0x4E
#define DS18X20_COPY_SCRATCHPAD   0x48
#define DS18X20_RECALL_E2         0xB8
#define DS18X20_COPYSP_DELAY      10 /* ms */
#define DS18X20_TH_REG      2
#define DS18X20_TL_REG      3


/* for description of functions see ds18x20.c */

extern void DS18X20_find_sensor(uint8_t *diff, uint8_t id[]);
	
extern uint8_t	DS18X20_get_power_status(uint8_t id[]);

extern uint8_t DS18X20_start_meas( uint8_t with_external, uint8_t id[]);
extern uint8_t DS18X20_read_meas(uint8_t id[], uint8_t *subzero, uint8_t *cel, uint8_t *cel_frac_bits);
extern uint8_t DS18X20_read_meas_single(uint8_t familycode, uint8_t *subzero, uint8_t *cel, uint8_t *cel_frac_bits);
extern uint8_t DS18X20_meas_to_cel( uint8_t fc, uint8_t *sp, uint8_t* subzero, uint8_t* cel, uint8_t* cel_frac_bits);
extern	uint16_t DS18X20_temp_to_decicel(uint8_t subzero, uint8_t cel, uint8_t cel_frac_bits);
extern int8_t DS18X20_temp_cmp(uint8_t subzero1, uint16_t cel1, uint8_t subzero2, uint16_t cel2);

#ifdef DS18X20_EEPROMSUPPORT
// write th, tl and config-register to scratchpad (config ignored on S20)
uint8_t DS18X20_write_scratchpad( uint8_t id[], uint8_t th, uint8_t tl, uint8_t conf);
// read scratchpad into array SP
uint8_t DS18X20_read_scratchpad( uint8_t id[], uint8_t sp[]);
// copy values th,tl (config) from scratchpad to DS18x20 eeprom
uint8_t DS18X20_copy_scratchpad( uint8_t with_power_extern, uint8_t id[] );
// copy values from DS18x20 eeprom to scratchpad
uint8_t DS18X20_recall_E2( uint8_t id[] );
#endif

#ifdef DS18X20_VERBOSE
extern void DS18X20_show_id_uart( uint8_t *id, size_t n );
extern uint8_t DS18X20_read_meas_all_verbose( void );
#endif

#endif