hzk.h

STM32 单片机例程

#if !defined( _HZK_H )
#define _HZK_H

#define  code

const uchar *PHZ=
"延时大约外设准备好等待";
//***********************************************************************/
const uchar HZK[]=
{
//-0-延
0X00,0X84,0XC4,0XA4,0X94,0X8C,0X00,0XE4,
0X04,0X04,0XFC,0X42,0X43,0X42,0X00,0X00,
0X80,0X44,0X28,0X10,0X2C,0X43,0X40,0X4F,
0X48,0X48,0X4F,0X48,0X48,0X48,0X40,0X00,
//-1-时
0X00,0XFC,0X84,0X84,0X84,0XFE,0X14,0X10,
0X90,0X10,0X10,0X10,0XFF,0X10,0X10,0X00,
0X00,0X3F,0X10,0X10,0X10,0X3F,0X00,0X00,
0X00,0X23,0X40,0X80,0X7F,0X00,0X00,0X00,
//-2-大
0X20,0X20,0X20,0X20,0X20,0X20,0XA0,0X7F,
0XA0,0X20,0X20,0X20,0X20,0X30,0X20,0X00,
0X00,0X40,0X40,0X20,0X10,0X0C,0X03,0X00,
0X01,0X06,0X08,0X10,0X20,0X60,0X20,0X00,
//-3-约
0X20,0X30,0XAC,0X63,0X20,0X50,0X20,0X18,
0X97,0X10,0X10,0X10,0X10,0XF8,0X10,0X00,
0X22,0X63,0X22,0X12,0X12,0X12,0X00,0X00,
0X00,0X21,0X43,0X80,0X40,0X3F,0X00,0X00,
//-4-外
0X00,0X80,0XE0,0X18,0X17,0X10,0X90,0X70,
0X00,0XFF,0X20,0X40,0X80,0X00,0X00,0X00,
0X01,0X40,0X20,0X11,0X0A,0X04,0X03,0X00,
0X00,0XFF,0X00,0X00,0X00,0X01,0X03,0X00,
//-5-设
0X40,0X40,0X42,0XCC,0X00,0X40,0XA0,0X9F,
0X81,0X81,0X81,0X9F,0XA0,0X20,0X20,0X00,
0X00,0X00,0X00,0X7F,0XA0,0X90,0X40,0X43,
0X2C,0X10,0X28,0X26,0X41,0XC0,0X40,0X00,
//-6-准
0X00,0X02,0X04,0XEC,0X40,0X20,0XF8,0X4F,
0X48,0X49,0XFE,0X48,0X48,0X4C,0X08,0X00,
0X02,0X02,0X7F,0X00,0X00,0X00,0XFF,0X22,
0X22,0X22,0X3F,0X22,0X22,0X32,0X20,0X00,
//-7-备
0X00,0X00,0X90,0X88,0X44,0X4B,0X32,0X12,
0X32,0X4A,0X47,0X82,0X80,0X00,0X00,0X00,
0X01,0X01,0X00,0XFF,0X49,0X49,0X49,0X7F,
0X49,0X49,0X49,0XFF,0X00,0X01,0X01,0X00,
//-8-好
0X10,0X10,0XF0,0X1F,0X10,0XF0,0X80,0X82,
0X82,0X82,0XE2,0X92,0X8A,0XC6,0X80,0X00,
0X40,0X22,0X15,0X08,0X14,0X63,0X00,0X00,
0X40,0X80,0X7F,0X00,0X00,0X00,0X00,0X00,
//-9-等
0X00,0X08,0X24,0X27,0X2C,0X24,0X24,0XF8,
0X24,0X27,0X2C,0X24,0X26,0X04,0X00,0X00,
0X01,0X05,0X05,0X05,0X0D,0X35,0X05,0X45,
0X85,0X7F,0X05,0X05,0X05,0X05,0X01,0X00,
//-10-待
/*
0X00,0X10,0X88,0XC4,0X33,0X40,0X44,0X44,
0X44,0X7F,0X44,0XC4,0X46,0X64,0X40,0X00,
0X02,0X01,0X00,0XFF,0X00,0X02,0X02,0X0A,
0X32,0X82,0X82,0X7F,0X02,0X02,0X02,0X00
*/
/*--  文字:  待  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=16x16   --*/
0x20,0x10,0x08,0xC7,0x3A,0x50,0x44,0x44,0x44,0x7F,0x44,0xC4,0x44,0x44,0x40,0x00,
0x00,0x02,0x01,0xFF,0x00,0x02,0x02,0x1A,0x02,0x42,0x82,0x7F,0x02,0x02,0x02,0x00
};



#endif