stm32f10x_dac.c

ssd1289驱动源码

  assert_param(IS_FUNCTIONAL_STATE(NewState));
  if (NewState != DISABLE)
  {
    /* Enable software trigger for both DAC channels */
    DAC->SWTRIGR |= DUAL_SWTRIG_SET ;
  }
  else
  {
    /* Disable software trigger for both DAC channels */
    DAC->SWTRIGR &= DUAL_SWTRIG_RESET;
  }
}

/**
  * @brief  Enables or disables the selected DAC channel wave generation.
  * @param  DAC_Channel: the selected DAC channel. 
  *   This parameter can be one of the following values:
  *     @arg DAC_Channel_1: DAC Channel1 selected
  *     @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_Wave: Specifies the wave type to enable or disable.
  *   This parameter can be one of the following values:
  *     @arg DAC_Wave_Noise: noise wave generation
  *     @arg DAC_Wave_Triangle: triangle wave generation
  * @param  NewState: new state of the selected DAC channel wave generation.
  *   This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void DAC_WaveGenerationCmd(uint32_t DAC_Channel, uint32_t DAC_Wave, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_DAC_WAVE(DAC_Wave)); 
  assert_param(IS_FUNCTIONAL_STATE(NewState));
  if (NewState != DISABLE)
  {
    /* Enable the selected wave generation for the selected DAC channel */
    DAC->CR |= DAC_Wave << DAC_Channel;
  }
  else
  {
    /* Disable the selected wave generation for the selected DAC channel */
    DAC->CR &= ~(DAC_Wave << DAC_Channel);
  }
}

/**
  * @brief  Set the specified data holding register value for DAC channel1.
  * @param  DAC_Align: Specifies the data alignment for DAC channel1.
  *   This parameter can be one of the following values:
  *     @arg DAC_Align_8b_R: 8bit right data alignment selected
  *     @arg DAC_Align_12b_L: 12bit left data alignment selected
  *     @arg DAC_Align_12b_R: 12bit right data alignment selected
  * @param  Data : Data to be loaded in the selected data holding register.
  * @retval None
  */
void DAC_SetChannel1Data(uint32_t DAC_Align, uint16_t Data)
{  
  __IO uint32_t tmp = 0;
  
  /* Check the parameters */
  assert_param(IS_DAC_ALIGN(DAC_Align));
  assert_param(IS_DAC_DATA(Data));
  
  tmp = (uint32_t)DAC_BASE; 
  tmp += DHR12R1_OFFSET + DAC_Align;

  /* Set the DAC channel1 selected data holding register */
  *(__IO uint32_t *) tmp = Data;
}

/**
  * @brief  Set the specified data holding register value for DAC channel2.
  * @param  DAC_Align: Specifies the data alignment for DAC channel2.
  *   This parameter can be one of the following values:
  *     @arg DAC_Align_8b_R: 8bit right data alignment selected
  *     @arg DAC_Align_12b_L: 12bit left data alignment selected
  *     @arg DAC_Align_12b_R: 12bit right data alignment selected
  * @param  Data : Data to be loaded in the selected data holding register.
  * @retval None
  */
void DAC_SetChannel2Data(uint32_t DAC_Align, uint16_t Data)
{
  __IO uint32_t tmp = 0;

  /* Check the parameters */
  assert_param(IS_DAC_ALIGN(DAC_Align));
  assert_param(IS_DAC_DATA(Data));
  
  tmp = (uint32_t)DAC_BASE;
  tmp += DHR12R2_OFFSET + DAC_Align;

  /* Set the DAC channel2 selected data holding register */
  *(__IO uint32_t *)tmp = Data;
}

/**
  * @brief  Set the specified data holding register value for dual channel
  *   DAC.
  * @param  DAC_Align: Specifies the data alignment for dual channel DAC.
  *   This parameter can be one of the following values:
  *     @arg DAC_Align_8b_R: 8bit right data alignment selected
  *     @arg DAC_Align_12b_L: 12bit left data alignment selected
  *     @arg DAC_Align_12b_R: 12bit right data alignment selected
  * @param  Data2: Data for DAC Channel2 to be loaded in the selected data 
  *   holding register.
  * @param  Data1: Data for DAC Channel1 to be loaded in the selected data 
  *   holding register.
  * @retval None
  */
void DAC_SetDualChannelData(uint32_t DAC_Align, uint16_t Data2, uint16_t Data1)
{
  uint32_t data = 0, tmp = 0;
  
  /* Check the parameters */
  assert_param(IS_DAC_ALIGN(DAC_Align));
  assert_param(IS_DAC_DATA(Data1));
  assert_param(IS_DAC_DATA(Data2));
  
  /* Calculate and set dual DAC data holding register value */
  if (DAC_Align == DAC_Align_8b_R)
  {
    data = ((uint32_t)Data2 << 8) | Data1; 
  }
  else
  {
    data = ((uint32_t)Data2 << 16) | Data1;
  }
  
  tmp = (uint32_t)DAC_BASE;
  tmp += DHR12RD_OFFSET + DAC_Align;

  /* Set the dual DAC selected data holding register */
  *(__IO uint32_t *)tmp = data;
}

/**
  * @brief  Returns the last data output value of the selected DAC channel.
  * @param  DAC_Channel: the selected DAC channel. 
  *   This parameter can be one of the following values:
  *     @arg DAC_Channel_1: DAC Channel1 selected
  *     @arg DAC_Channel_2: DAC Channel2 selected
  * @retval The selected DAC channel data output value.
  */
uint16_t DAC_GetDataOutputValue(uint32_t DAC_Channel)
{
  __IO uint32_t tmp = 0;
  
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  
  tmp = (uint32_t) DAC_BASE ;
  tmp += DOR_OFFSET + ((uint32_t)DAC_Channel >> 2);
  
  /* Returns the DAC channel data output register value */
  return (uint16_t) (*(__IO uint32_t*) tmp);
}

#if defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || defined (STM32F10X_HD_VL)
/**
  * @brief  Checks whether the specified DAC flag is set or not.
  * @param  DAC_Channel: thee selected DAC channel. 
  *   This parameter can be one of the following values:
  *     @arg DAC_Channel_1: DAC Channel1 selected
  *     @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_FLAG: specifies the flag to check. 
  *   This parameter can be only of the following value:
  *     @arg DAC_FLAG_DMAUDR: DMA underrun flag                                                 
  * @retval The new state of DAC_FLAG (SET or RESET).
  */
FlagStatus DAC_GetFlagStatus(uint32_t DAC_Channel, uint32_t DAC_FLAG)
{
  FlagStatus bitstatus = RESET;
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_DAC_FLAG(DAC_FLAG));

  /* Check the status of the specified DAC flag */
  if ((DAC->SR & (DAC_FLAG << DAC_Channel)) != (uint8_t)RESET)
  {
    /* DAC_FLAG is set */
    bitstatus = SET;
  }
  else
  {
    /* DAC_FLAG is reset */
    bitstatus = RESET;
  }
  /* Return the DAC_FLAG status */
  return  bitstatus;
}

/**
  * @brief  Clears the DAC channelx's pending flags.
  * @param  DAC_Channel: the selected DAC channel. 
  *   This parameter can be one of the following values:
  *     @arg DAC_Channel_1: DAC Channel1 selected
  *     @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_FLAG: specifies the flag to clear. 
  *   This parameter can be of the following value:
  *     @arg DAC_FLAG_DMAUDR: DMA underrun flag                           
  * @retval None
  */
void DAC_ClearFlag(uint32_t DAC_Channel, uint32_t DAC_FLAG)
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_DAC_FLAG(DAC_FLAG));

  /* Clear the selected DAC flags */
  DAC->SR = (DAC_FLAG << DAC_Channel);
}

/**
  * @brief  Checks whether the specified DAC interrupt has occurred or not.
  * @param  DAC_Channel: the selected DAC channel. 
  *   This parameter can be one of the following values:
  *     @arg DAC_Channel_1: DAC Channel1 selected
  *     @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_IT: specifies the DAC interrupt source to check. 
  *   This parameter can be the following values:
  *     @arg DAC_IT_DMAUDR: DMA underrun interrupt mask                       
  * @retval The new state of DAC_IT (SET or RESET).
  */
ITStatus DAC_GetITStatus(uint32_t DAC_Channel, uint32_t DAC_IT)
{
  ITStatus bitstatus = RESET;
  uint32_t enablestatus = 0;
  
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_DAC_IT(DAC_IT));

  /* Get the DAC_IT enable bit status */
  enablestatus = (DAC->CR & (DAC_IT << DAC_Channel)) ;
  
  /* Check the status of the specified DAC interrupt */
  if (((DAC->SR & (DAC_IT << DAC_Channel)) != (uint32_t)RESET) && enablestatus)
  {
    /* DAC_IT is set */
    bitstatus = SET;
  }
  else
  {
    /* DAC_IT is reset */
    bitstatus = RESET;
  }
  /* Return the DAC_IT status */
  return  bitstatus;
}

/**
  * @brief  Clears the DAC channelx's interrupt pending bits.
  * @param  DAC_Channel: the selected DAC channel. 
  *   This parameter can be one of the following values:
  *     @arg DAC_Channel_1: DAC Channel1 selected
  *     @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_IT: specifies the DAC interrupt pending bit to clear.
  *   This parameter can be the following values:
  *     @arg DAC_IT_DMAUDR: DMA underrun interrupt mask                         
  * @retval None
  */
void DAC_ClearITPendingBit(uint32_t DAC_Channel, uint32_t DAC_IT)
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_DAC_IT(DAC_IT)); 

  /* Clear the selected DAC interrupt pending bits */
  DAC->SR = (DAC_IT << DAC_Channel);
}
#endif

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/