stm32f10x_i2c.c

ssd1289驱动源码

/**
  * @brief  Selects the specified I2C PEC position.
  * @param  I2Cx: where x can be 1 or 2 to select the I2C peripheral.
  * @param  I2C_PECPosition: specifies the PEC position. 
  *   This parameter can be one of the following values:
  *     @arg I2C_PECPosition_Next: indicates that the next byte is PEC
  *     @arg I2C_PECPosition_Current: indicates that current byte is PEC
  * @retval None
  */
void I2C_PECPositionConfig(I2C_TypeDef* I2Cx, uint16_t I2C_PECPosition)
{
  /* Check the parameters */
  assert_param(IS_I2C_ALL_PERIPH(I2Cx));
  assert_param(IS_I2C_PEC_POSITION(I2C_PECPosition));
  if (I2C_PECPosition == I2C_PECPosition_Next)
  {
    /* Next byte in shift register is PEC */
    I2Cx->CR1 |= I2C_PECPosition_Next;
  }
  else
  {
    /* Current byte in shift register is PEC */
    I2Cx->CR1 &= I2C_PECPosition_Current;
  }
}

/**
  * @brief  Enables or disables the PEC value calculation of the transfered bytes.
  * @param  I2Cx: where x can be 1 or 2 to select the I2C peripheral.
  * @param  NewState: new state of the I2Cx PEC value calculation.
  *   This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void I2C_CalculatePEC(I2C_TypeDef* I2Cx, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_I2C_ALL_PERIPH(I2Cx));
  assert_param(IS_FUNCTIONAL_STATE(NewState));
  if (NewState != DISABLE)
  {
    /* Enable the selected I2C PEC calculation */
    I2Cx->CR1 |= CR1_ENPEC_Set;
  }
  else
  {
    /* Disable the selected I2C PEC calculation */
    I2Cx->CR1 &= CR1_ENPEC_Reset;
  }
}

/**
  * @brief  Returns the PEC value for the specified I2C.
  * @param  I2Cx: where x can be 1 or 2 to select the I2C peripheral.
  * @retval The PEC value.
  */
uint8_t I2C_GetPEC(I2C_TypeDef* I2Cx)
{
  /* Check the parameters */
  assert_param(IS_I2C_ALL_PERIPH(I2Cx));
  /* Return the selected I2C PEC value */
  return ((I2Cx->SR2) >> 8);
}

/**
  * @brief  Enables or disables the specified I2C ARP.
  * @param  I2Cx: where x can be 1 or 2 to select the I2C peripheral.
  * @param  NewState: new state of the I2Cx ARP. 
  *   This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void I2C_ARPCmd(I2C_TypeDef* I2Cx, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_I2C_ALL_PERIPH(I2Cx));
  assert_param(IS_FUNCTIONAL_STATE(NewState));
  if (NewState != DISABLE)
  {
    /* Enable the selected I2C ARP */
    I2Cx->CR1 |= CR1_ENARP_Set;
  }
  else
  {
    /* Disable the selected I2C ARP */
    I2Cx->CR1 &= CR1_ENARP_Reset;
  }
}

/**
  * @brief  Enables or disables the specified I2C Clock stretching.
  * @param  I2Cx: where x can be 1 or 2 to select the I2C peripheral.
  * @param  NewState: new state of the I2Cx Clock stretching.
  *   This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void I2C_StretchClockCmd(I2C_TypeDef* I2Cx, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_I2C_ALL_PERIPH(I2Cx));
  assert_param(IS_FUNCTIONAL_STATE(NewState));
  if (NewState == DISABLE)
  {
    /* Enable the selected I2C Clock stretching */
    I2Cx->CR1 |= CR1_NOSTRETCH_Set;
  }
  else
  {
    /* Disable the selected I2C Clock stretching */
    I2Cx->CR1 &= CR1_NOSTRETCH_Reset;
  }
}

/**
  * @brief  Selects the specified I2C fast mode duty cycle.
  * @param  I2Cx: where x can be 1 or 2 to select the I2C peripheral.
  * @param  I2C_DutyCycle: specifies the fast mode duty cycle.
  *   This parameter can be one of the following values:
  *     @arg I2C_DutyCycle_2: I2C fast mode Tlow/Thigh = 2
  *     @arg I2C_DutyCycle_16_9: I2C fast mode Tlow/Thigh = 16/9
  * @retval None
  */
void I2C_FastModeDutyCycleConfig(I2C_TypeDef* I2Cx, uint16_t I2C_DutyCycle)
{
  /* Check the parameters */
  assert_param(IS_I2C_ALL_PERIPH(I2Cx));
  assert_param(IS_I2C_DUTY_CYCLE(I2C_DutyCycle));
  if (I2C_DutyCycle != I2C_DutyCycle_16_9)
  {
    /* I2C fast mode Tlow/Thigh=2 */
    I2Cx->CCR &= I2C_DutyCycle_2;
  }
  else
  {
    /* I2C fast mode Tlow/Thigh=16/9 */
    I2Cx->CCR |= I2C_DutyCycle_16_9;
  }
}



/**
 * @brief
 ****************************************************************************************
 *
 *                         I2C State Monitoring Functions
 *                       
 ****************************************************************************************   
 * This I2C driver provides three different ways for I2C state monitoring
 *  depending on the application requirements and constraints:
 *        
 *  
 * 1) Basic state monitoring:
 *    Using I2C_CheckEvent() function:
 *    It compares the status registers (SR1 and SR2) content to a given event
 *    (can be the combination of one or more flags).
 *    It returns SUCCESS if the current status includes the given flags 
 *    and returns ERROR if one or more flags are missing in the current status.
 *    - When to use:
 *      - This function is suitable for most applciations as well as for startup 
 *      activity since the events are fully described in the product reference manual 
 *      (RM0008).
 *      - It is also suitable for users who need to define their own events.
 *    - Limitations:
 *      - If an error occurs (ie. error flags are set besides to the monitored flags),
 *        the I2C_CheckEvent() function may return SUCCESS despite the communication
 *        hold or corrupted real state. 
 *        In this case, it is advised to use error interrupts to monitor the error
 *        events and handle them in the interrupt IRQ handler.
 *        
 *        @note 
 *        For error management, it is advised to use the following functions:
 *          - I2C_ITConfig() to configure and enable the error interrupts (I2C_IT_ERR).
 *          - I2Cx_ER_IRQHandler() which is called when the error interurpt occurs.
 *            Where x is the peripheral instance (I2C1, I2C2 ...)
 *          - I2C_GetFlagStatus() or I2C_GetITStatus() to be called into I2Cx_ER_IRQHandler() 
 *            in order to determine which error occured.
 *          - I2C_ClearFlag() or I2C_ClearITPendingBit() and/or I2C_SoftwareResetCmd()
 *            and/or I2C_GenerateStop() in order to clear the error flag and source,
 *            and return to correct communication status.
 *            
 *
 *  2) Advanced state monitoring:
 *     Using the function I2C_GetLastEvent() which returns the image of both status 
 *     registers in a single word (uint32_t) (Status Register 2 value is shifted left 
 *     by 16 bits and concatenated to Status Register 1).
 *     - When to use:
 *       - This function is suitable for the same applications above but it allows to
 *         overcome the mentionned limitation of I2C_GetFlagStatus() function.
 *         The returned value could be compared to events already defined in the 
 *         library (stm32f10x_i2c.h) or to custom values defiend by user.
 *       - This function is suitable when multiple flags are monitored at the same time.
 *       - At the opposite of I2C_CheckEvent() function, this function allows user to
 *         choose when an event is accepted (when all events flags are set and no 
 *         other flags are set or just when the needed flags are set like 
 *         I2C_CheckEvent() function).
 *     - Limitations:
 *       - User may need to define his own events.
 *       - Same remark concerning the error management is applicable for this 
 *         function if user decides to check only regular communication flags (and 
 *         ignores error flags).
 *     
 *
 *  3) Flag-based state monitoring:
 *     Using the function I2C_GetFlagStatus() which simply returns the status of 
 *     one single flag (ie. I2C_FLAG_RXNE ...). 
 *     - When to use:
 *        - This function could be used for specific applications or in debug phase.
 *        - It is suitable when only one flag checking is needed (most I2C events 
 *          are monitored through multiple flags).
 *     - Limitations: 
 *        - When calling this function, the Status register is accessed. Some flags are
 *          cleared when the status register is accessed. So checking the status
 *          of one Flag, may clear other ones.
 *        - Function may need to be called twice or more in order to monitor one 
 *          single event.
 *
 *  For detailed description of Events, please refer to section I2C_Events in 
 *  stm32f10x_i2c.h file.
 *  
 */

/**
 * 
 *  1) Basic state monitoring
 *******************************************************************************
 */

/**
  * @brief  Checks whether the last I2Cx Event is equal to the one passed
  *   as parameter.
  * @param  I2Cx: where x can be 1 or 2 to select the I2C peripheral.
  * @param  I2C_EVENT: specifies the event to be checked. 
  *   This parameter can be one of the following values:
  *     @arg I2C_EVENT_SLAVE_TRANSMITTER_ADDRESS_MATCHED           : EV1
  *     @arg I2C_EVENT_SLAVE_RECEIVER_ADDRESS_MATCHED              : EV1
  *     @arg I2C_EVENT_SLAVE_TRANSMITTER_SECONDADDRESS_MATCHED     : EV1
  *     @arg I2C_EVENT_SLAVE_RECEIVER_SECONDADDRESS_MATCHED        : EV1
  *     @arg I2C_EVENT_SLAVE_GENERALCALLADDRESS_MATCHED            : EV1
  *     @arg I2C_EVENT_SLAVE_BYTE_RECEIVED                         : EV2
  *     @arg (I2C_EVENT_SLAVE_BYTE_RECEIVED | I2C_FLAG_DUALF)      : EV2
  *     @arg (I2C_EVENT_SLAVE_BYTE_RECEIVED | I2C_FLAG_GENCALL)    : EV2
  *     @arg I2C_EVENT_SLAVE_BYTE_TRANSMITTED                      : EV3
  *     @arg (I2C_EVENT_SLAVE_BYTE_TRANSMITTED | I2C_FLAG_DUALF)   : EV3
  *     @arg (I2C_EVENT_SLAVE_BYTE_TRANSMITTED | I2C_FLAG_GENCALL) : EV3
  *     @arg I2C_EVENT_SLAVE_ACK_FAILURE                           : EV3_2
  *     @arg I2C_EVENT_SLAVE_STOP_DETECTED                         : EV4
  *     @arg I2C_EVENT_MASTER_MODE_SELECT                          : EV5
  *     @arg I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED            : EV6     
  *     @arg I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED               : EV6
  *     @arg I2C_EVENT_MASTER_BYTE_RECEIVED                        : EV7
  *     @arg I2C_EVENT_MASTER_BYTE_TRANSMITTING                    : EV8
  *     @arg I2C_EVENT_MASTER_BYTE_TRANSMITTED                     : EV8_2
  *     @arg I2C_EVENT_MASTER_MODE_ADDRESS10                       : EV9
  *     
  * @note: For detailed description of Events, please refer to section 
  *    I2C_Events in stm32f10x_i2c.h file.
  *    
  * @retval An ErrorStatus enumuration value:
  * - SUCCESS: Last event is equal to the I2C_EVENT
  * - ERROR: Last event is different from the I2C_EVENT
  */
ErrorStatus I2C_CheckEvent(I2C_TypeDef* I2Cx, uint32_t I2C_EVENT)
{
  uint32_t lastevent = 0;
  uint32_t flag1 = 0, flag2 = 0;
  ErrorStatus status = ERROR;

  /* Check the parameters */
  assert_param(IS_I2C_ALL_PERIPH(I2Cx));
  assert_param(IS_I2C_EVENT(I2C_EVENT));

  /* Read the I2Cx status register */
  flag1 = I2Cx->SR1;
  flag2 = I2Cx->SR2;
  flag2 = flag2 << 16;

  /* Get the last event value from I2C status register */
  lastevent = (flag1 | flag2) & FLAG_Mask;

  /* Check whether the last event contains the I2C_EVENT */
  if ((lastevent & I2C_EVENT) == I2C_EVENT)
  {
    /* SUCCESS: last event is equal to I2C_EVENT */
    status = SUCCESS;
  }
  else
  {
    /* ERROR: last event is different from I2C_EVENT */
    status = ERROR;
  }
  /* Return status */
  return status;
}

/**
 * 
 *  2) Advanced state monitoring
 *******************************************************************************
 */

/**
  * @brief  Returns the last I2Cx Event.
  * @param  I2Cx: where x can be 1 or 2 to select the I2C peripheral.
  *     
  * @note: For detailed description of Events, please refer to section 
  *    I2C_Events in stm32f10x_i2c.h file.
  *    
  * @retval The last event
  */
uint32_t I2C_GetLastEvent(I2C_TypeDef* I2Cx)
{
  uint32_t lastevent = 0;
  uint32_t flag1 = 0, flag2 = 0;

  /* Check the parameters */
  assert_param(IS_I2C_ALL_PERIPH(I2Cx));

  /* Read the I2Cx status register */
  flag1 = I2Cx->SR1;
  flag2 = I2Cx->SR2;
  flag2 = flag2 << 16;

  /* Get the last event value from I2C status register */
  lastevent = (flag1 | flag2) & FLAG_Mask;

  /* Return status */
  return lastevent;
}

/**
 * 
 *  3) Flag-based state monitoring
 *******************************************************************************
 */

/**
  * @brief  Checks whether the specified I2C flag is set or not.
  * @param  I2Cx: where x can be 1 or 2 to select the I2C peripheral.
  * @param  I2C_FLAG: specifies the flag to check. 
  *   This parameter can be one of the following values:
  *     @arg I2C_FLAG_DUALF: Dual flag (Slave mode)
  *     @arg I2C_FLAG_SMBHOST: SMBus host header (Slave mode)
  *     @arg I2C_FLAG_SMBDEFAULT: SMBus default header (Slave mode)
  *     @arg I2C_FLAG_GENCALL: General call header flag (Slave mode)
  *     @arg I2C_FLAG_TRA: Transmitter/Receiver flag
  *     @arg I2C_FLAG_BUSY: Bus busy flag
  *     @arg I2C_FLAG_MSL: Master/Slave flag
  *     @arg I2C_FLAG_SMBALERT: SMBus Alert flag
  *     @arg I2C_FLAG_TIMEOUT: Timeout or Tlow error flag
  *     @arg I2C_FLAG_PECERR: PEC error in reception flag
  *     @arg I2C_FLAG_OVR: Overrun/Underrun flag (Slave mode)
  *     @arg I2C_FLAG_AF: Acknowledge failure flag
  *     @arg I2C_FLAG_ARLO: Arbitration lost flag (Master mode)
  *     @arg I2C_FLAG_BERR: Bus error flag
  *     @arg I2C_FLAG_TXE: Data register empty flag (Transmitter)
  *     @arg I2C_FLAG_RXNE: Data register not empty (Receiver) flag
  *     @arg I2C_FLAG_STOPF: Stop detection flag (Slave mode)
  *     @arg I2C_FLAG_ADD10: 10-bit header sent flag (Master mode)
  *     @arg I2C_FLAG_BTF: Byte transfer finished flag
  *     @arg I2C_FLAG_ADDR: Address sent flag (Master mode) 揂DSL