📄 atahost_controller.vhd
字号:
---------------------------------------------------------------------
---- ----
---- OpenCores IDE Controller ----
---- ATA/ATAPI-5 Controller (OCIDEC-2) ----
---- ----
---- Author: Richard Herveille ----
---- richard@asics.ws ----
---- www.asics.ws ----
---- ----
---------------------------------------------------------------------
---- ----
---- Copyright (C) 2001, 2002 Richard Herveille ----
---- richard@asics.ws ----
---- ----
---- This source file may be used and distributed without ----
---- restriction provided that this copyright statement is not ----
---- removed from the file and that any derivative work contains ----
---- the original copyright notice and the associated disclaimer.----
---- ----
---- THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY ----
---- EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED ----
---- TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS ----
---- FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL THE AUTHOR ----
---- OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, ----
---- INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ----
---- (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE ----
---- GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR ----
---- BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF ----
---- LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ----
---- (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT ----
---- OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE ----
---- POSSIBILITY OF SUCH DAMAGE. ----
---- ----
---------------------------------------------------------------------
-- rev.: 1.0 march 18th, 2001. Initial release
-- rev.: 1.0a april 12th, 2001. Removed references to records.vhd
-- rev.: 1.1 june 18th, 2001. Changed PIOack generation. Avoid asserting PIOack continuously when IDEen = '0'
-- rev.: 1.2 june 26th, 2001. Changed dPIOreq generation. Core did not support wishbone burst accesses to ATA-device.
-- rev.: 1.3 july 11th, 2001. Changed PIOreq & PIOack generation (made them synchronous).
--
-- CVS Log
--
-- $Id: atahost_controller.vhd,v 1.2 2002/05/19 06:07:09 rherveille Exp $
--
-- $Date: 2002/05/19 06:07:09 $
-- $Revision: 1.2 $
-- $Author: rherveille $
-- $Locker: $
-- $State: Exp $
--
-- Change History:
-- $Log: atahost_controller.vhd,v $
-- Revision 1.2 2002/05/19 06:07:09 rherveille
-- Fixed a potential bug where the core was forced into an unknown state
-- when an asynchronous reset was given without a running clock.
--
--
--
-- OCIDEC2 supports:
-- -Common Compatible timing access to all connected devices
-- -Separate timing accesses to data port
-- -No DMA support
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_arith.all;
entity atahost_controller is
generic(
TWIDTH : natural := 8; -- counter width
-- PIO mode 0 settings (@100MHz clock)
PIO_mode0_T1 : natural := 6; -- 70ns
PIO_mode0_T2 : natural := 28; -- 290ns
PIO_mode0_T4 : natural := 2; -- 30ns
PIO_mode0_Teoc : natural := 23 -- 240ns ==> T0 - T1 - T2 = 600 - 70 - 290 = 240
);
port(
clk : in std_logic; -- master clock in
nReset : in std_logic := '1'; -- asynchronous active low reset
rst : in std_logic := '0'; -- synchronous active high reset
irq : out std_logic; -- interrupt request signal
-- control / registers
IDEctrl_rst,
IDEctrl_IDEen,
IDEctrl_FATR0,
IDEctrl_FATR1 : in std_logic;
-- PIO registers
cmdport_T1,
cmdport_T2,
cmdport_T4,
cmdport_Teoc : in unsigned(7 downto 0);
cmdport_IORDYen : in std_logic; -- PIO command port / non-fast timing
dport0_T1,
dport0_T2,
dport0_T4,
dport0_Teoc : in unsigned(7 downto 0);
dport0_IORDYen : in std_logic; -- PIO mode data-port / fast timing device 0
dport1_T1,
dport1_T2,
dport1_T4,
dport1_Teoc : in unsigned(7 downto 0);
dport1_IORDYen : in std_logic; -- PIO mode data-port / fast timing device 1
PIOreq : in std_logic; -- PIO transfer request
PIOack : buffer std_logic; -- PIO transfer ended
PIOa : in unsigned(3 downto 0); -- PIO address
PIOd : in std_logic_vector(15 downto 0); -- PIO data in
PIOq : out std_logic_vector(15 downto 0); -- PIO data out
PIOwe : in std_logic; -- PIO direction bit '1'=write, '0'=read
-- ATA signals
RESETn : out std_logic;
DDi : in std_logic_vector(15 downto 0);
DDo : out std_logic_vector(15 downto 0);
DDoe : out std_logic;
DA : out unsigned(2 downto 0);
CS0n : out std_logic;
CS1n : out std_logic;
DIORn : out std_logic;
DIOWn : out std_logic;
IORDY : in std_logic;
INTRQ : in std_logic
);
end entity atahost_controller;
architecture structural of atahost_controller is
--
-- component declarations
--
component atahost_pio_actrl is
generic(
TWIDTH : natural := 8; -- counter width
-- PIO mode 0 settings (@100MHz clock)
PIO_mode0_T1 : natural := 6; -- 70ns
PIO_mode0_T2 : natural := 28; -- 290ns
PIO_mode0_T4 : natural := 2; -- 30ns
PIO_mode0_Teoc : natural := 23 -- 240ns ==> T0 - T1 - T2 = 600 - 70 - 290 = 240
);
port(
clk : in std_logic; -- master clock
nReset : in std_logic; -- asynchronous active low reset
rst : in std_logic; -- synchronous active high reset
IDEctrl_FATR0,
IDEctrl_FATR1 : in std_logic;
cmdport_T1,
cmdport_T2,
cmdport_T4,
cmdport_Teoc : in unsigned(7 downto 0);
cmdport_IORDYen : in std_logic; -- PIO command port / non-fast timing
dport0_T1,
dport0_T2,
dport0_T4,
dport0_Teoc : in unsigned(7 downto 0);
dport0_IORDYen : in std_logic; -- PIO mode data-port / fast timing device 0
dport1_T1,
dport1_T2,
dport1_T4,
dport1_Teoc : in unsigned(7 downto 0);
dport1_IORDYen : in std_logic; -- PIO mode data-port / fast timing device 1
SelDev : in std_logic; -- Selected device
go : in std_logic; -- Start transfer sequence
done : out std_logic; -- Transfer sequence done
dir : in std_logic; -- Transfer direction '1'=write, '0'=read
a : in unsigned(3 downto 0); -- PIO transfer address
q : out std_logic_vector(15 downto 0); -- Data read from ATA devices
DDi : in std_logic_vector(15 downto 0); -- Data from ATA DD bus
oe : buffer std_logic; -- DDbus output-enable signal
DIOR,
DIOW : buffer std_logic;
IORDY : in std_logic
);
end component atahost_pio_actrl;
--
-- signals
--
signal SelDev : std_logic; -- selected device
signal dPIOreq, PIOgo : std_logic; -- start PIO timing controller
signal PIOdone : std_logic; -- PIO timing controller done
-- PIO signals
signal PIOdior, PIOdiow : std_logic;
signal PIOoe : std_logic;
-- synchronized ATA inputs
signal sIORDY : std_logic;
begin
--
-- synchronize incoming signals
--
synch_incoming: block
signal cIORDY : std_logic; -- capture IORDY
signal cINTRQ : std_logic; -- capture INTRQ
begin
process(clk)
begin
if (clk'event and clk = '1') then
cIORDY <= IORDY;
cINTRQ <= INTRQ;
sIORDY <= cIORDY;
irq <= cINTRQ;
end if;
end process;
end block synch_incoming;
--
-- generate ATA signals
--
gen_ata_sigs: block
begin
-- generate registers for ATA signals
gen_regs: process(clk, nReset)
begin
if (nReset = '0') then
RESETn <= '0';
DIORn <= '1';
DIOWn <= '1';
DA <= (others => '0');
CS0n <= '1';
CS1n <= '1';
DDo <= (others => '0');
DDoe <= '0';
elsif (clk'event and clk = '1') then
if (rst = '1') then
RESETn <= '0';
DIORn <= '1';
DIOWn <= '1';
DA <= (others => '0');
CS0n <= '1';
CS1n <= '1';
DDo <= (others => '0');
DDoe <= '0';
else
RESETn <= not IDEctrl_rst;
DA <= PIOa(2 downto 0);
CS0n <= not (not PIOa(3) and PIOreq); -- CS0 asserted when A(3) = '0'
CS1n <= not ( PIOa(3) and PIOreq); -- CS1 asserted when A(3) = '1'
DDo <= PIOd;
DDoe <= PIOoe;
DIORn <= not PIOdior;
DIOWn <= not PIOdiow;
end if;
end if;
end process gen_regs;
end block gen_ata_sigs;
--
-- generate selected device
--
gen_seldev: process(clk)
variable Asel : std_logic; -- address selected
begin
Asel := not PIOa(3) and PIOa(2) and PIOa(1) and not PIOa(0); -- header/device register
if (clk'event and clk = '1') then
if ( (PIOdone = '1') and (Asel = '1') and (PIOwe = '1') ) then
SelDev <= PIOd(4);
end if;
end if;
end process gen_seldev;
-- generate PIOgo signal
gen_PIOgo: process(clk, nReset)
begin
if (nReset = '0') then
dPIOreq <= '0';
PIOgo <= '0';
elsif (clk'event and clk = '1') then
if (rst = '1') then
dPIOreq <= '0';
PIOgo <= '0';
else
dPIOreq <= PIOreq and not PIOack;
PIOgo <= (PIOreq and not dPIOreq) and IDEctrl_IDEen;
end if;
end
end process gen_PIOgo;
--
-- Hookup PIO access controller
--
PIO_access_control: atahost_pio_actrl
generic map(
TWIDTH => TWIDTH,
PIO_mode0_T1 => PIO_mode0_T1,
PIO_mode0_T2 => PIO_mode0_T2,
PIO_mode0_T4 => PIO_mode0_T4,
PIO_mode0_Teoc => PIO_mode0_Teoc
)
port map(
clk => clk,
nReset => nReset,
rst => rst,
IDEctrl_FATR0 => IDEctrl_FATR0,
IDEctrl_FATR1 => IDEctrl_FATR1,
cmdport_T1 => cmdport_T1,
cmdport_T2 => cmdport_T2,
cmdport_T4 => cmdport_T4,
cmdport_Teoc => cmdport_Teoc,
cmdport_IORDYen => cmdport_IORDYen,
dport0_T1 => dport0_T1,
dport0_T2 => dport0_T2,
dport0_T4 => dport0_T4,
dport0_Teoc => dport0_Teoc,
dport0_IORDYen => dport0_IORDYen,
dport1_T1 => dport1_T1,
dport1_T2 => dport1_T2,
dport1_T4 => dport1_T4,
dport1_Teoc => dport1_Teoc,
dport1_IORDYen => dport1_IORDYen,
SelDev => SelDev,
go => PIOgo,
done => PIOdone,
dir => PIOwe,
a => PIOa,
q => PIOq,
DDi => DDi,
oe => PIOoe,
DIOR => PIOdior,
DIOW => PIOdiow,
IORDY => sIORDY
);
-- generate acknowledge
gen_ack: process(clk)
begin
if (clk'event and clk = '1') the
PIOack <= PIOdone or (PIOreq and not IDEctrl_IDEen); -- acknowledge when done or when IDE not enabled (discard request)
end if;
end process gen_ack;
end architecture structural;
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -