stm32f2xx_spi.c

STM32+Grlib

/**
  ******************************************************************************
  * @file    stm32f2xx_spi.c
  * @author  MCD Application Team
  * @version V1.0.0
  * @date    18-April-2011
  * @brief   This file provides firmware functions to manage the following 
  *          functionalities of the Serial peripheral interface (SPI):           
  *           - Initialization and Configuration
  *           - Data transfers functions
  *           - Hardware CRC Calculation
  *           - DMA transfers management
  *           - Interrupts and flags management 
  *           
  *  @verbatim
  *          
  *                    
  *          ===================================================================
  *                                 How to use this driver
  *          ===================================================================
  *          1. Enable peripheral clock using the following functions 
  *             RCC_APB2PeriphClockCmd(RCC_APB2Periph_SPI1, ENABLE) for SPI1
  *             RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPI2, ENABLE) for SPI2
  *             RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI3, ENABLE) for SPI3.
  *
  *          2. Enable SCK, MOSI, MISO and NSS GPIO clocks using RCC_AHB1PeriphClockCmd()
  *             function.
  *             In I2S mode, if an external clock source is used then the I2S CKIN pin GPIO
  *             clock should also be enabled.
  *
  *          3. Peripherals alternate function: 
  *                 - Connect the pin to the desired peripherals' Alternate 
  *                   Function (AF) using GPIO_PinAFConfig() function
  *                 - Configure the desired pin in alternate function by:
  *                   GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AF
  *                 - Select the type, pull-up/pull-down and output speed via 
  *                   GPIO_PuPd, GPIO_OType and GPIO_Speed members
  *                 - Call GPIO_Init() function
  *              In I2S mode, if an external clock source is used then the I2S CKIN pin
  *              should be also configured in Alternate function Push-pull pull-up mode. 
  *        
  *          4. Program the Polarity, Phase, First Data, Baud Rate Prescaler, Slave 
  *             Management, Peripheral Mode and CRC Polynomial values using the SPI_Init()
  *             function.
  *             In I2S mode, program the Mode, Standard, Data Format, MCLK Output, Audio 
  *             frequency and Polarity using I2S_Init() function.
  *             For I2S mode, make sure that either:
  *              - I2S PLL is configured using the functions RCC_I2SCLKConfig(RCC_I2S2CLKSource_PLLI2S), 
  *                RCC_PLLI2SCmd(ENABLE) and RCC_GetFlagStatus(RCC_FLAG_PLLI2SRDY).
  *              or 
  *              - External clock source is configured using the function 
  *                RCC_I2SCLKConfig(RCC_I2S2CLKSource_Ext) and after setting correctly the define constant
  *                I2S_EXTERNAL_CLOCK_VAL in the stm32f2xx_conf.h file. 
  *
  *          5. Enable the NVIC and the corresponding interrupt using the function 
  *             SPI_ITConfig() if you need to use interrupt mode. 
  *
  *          6. When using the DMA mode 
  *                   - Configure the DMA using DMA_Init() function
  *                   - Active the needed channel Request using SPI_I2S_DMACmd() function
  * 
  *          7. Enable the SPI using the SPI_Cmd() function or enable the I2S using
  *             I2S_Cmd().
  * 
  *          8. Enable the DMA using the DMA_Cmd() function when using DMA mode. 
  *
  *          9. Optionally, you can enable/configure the following parameters without
  *             re-initialization (i.e there is no need to call again SPI_Init() function):
  *              - When bidirectional mode (SPI_Direction_1Line_Rx or SPI_Direction_1Line_Tx)
  *                is programmed as Data direction parameter using the SPI_Init() function
  *                it can be possible to switch between SPI_Direction_Tx or SPI_Direction_Rx
  *                using the SPI_BiDirectionalLineConfig() function.
  *              - When SPI_NSS_Soft is selected as Slave Select Management parameter 
  *                using the SPI_Init() function it can be possible to manage the 
  *                NSS internal signal using the SPI_NSSInternalSoftwareConfig() function.
  *              - Reconfigure the data size using the SPI_DataSizeConfig() function  
  *              - Enable or disable the SS output using the SPI_SSOutputCmd() function  
  *          
  *          10. To use the CRC Hardware calculation feature refer to the Peripheral 
  *              CRC hardware Calculation subsection.
  *   
  *
  * @note    This driver supports only the I2S clock scheme available in Silicon
  *          RevisionB and RevisionY.
  *     
  * @note    In I2S mode: if an external clock is used as source clock for the I2S,  
  *          then the define I2S_EXTERNAL_CLOCK_VAL in file stm32f2xx_conf.h should 
  *          be enabled and set to the value of the source clock frequency (in Hz).
  * 
  * @note    In SPI mode: To use the SPI TI mode, call the function SPI_TIModeCmd() 
  *          just after calling the function SPI_Init().
  *
  *  @endverbatim  
  *                                  
  ******************************************************************************
  * @attention
  *
  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
  *
  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
  ******************************************************************************  
  */ 

/* Includes ------------------------------------------------------------------*/
#include "stm32f2xx_spi.h"
#include "stm32f2xx_rcc.h"

/** @addtogroup STM32F2xx_StdPeriph_Driver
  * @{
  */

/** @defgroup SPI 
  * @brief SPI driver modules
  * @{
  */ 

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/

/* SPI registers Masks */
#define CR1_CLEAR_MASK            ((uint16_t)0x3040)
#define I2SCFGR_CLEAR_MASK        ((uint16_t)0xF040)

/* RCC PLLs masks */
#define PLLCFGR_PPLR_MASK         ((uint32_t)0x70000000)
#define PLLCFGR_PPLN_MASK         ((uint32_t)0x00007FC0)

#define SPI_CR2_FRF               ((uint16_t)0x0010)
#define SPI_SR_TIFRFE             ((uint16_t)0x0100)

/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/

/** @defgroup SPI_Private_Functions
  * @{
  */

/** @defgroup SPI_Group1 Initialization and Configuration functions
 *  @brief   Initialization and Configuration functions 
 *
@verbatim   
 ===============================================================================
                  Initialization and Configuration functions
 ===============================================================================  

  This section provides a set of functions allowing to initialize the SPI Direction,
  SPI Mode, SPI Data Size, SPI Polarity, SPI Phase, SPI NSS Management, SPI Baud
  Rate Prescaler, SPI First Bit and SPI CRC Polynomial.
  
  The SPI_Init() function follows the SPI configuration procedures for Master mode
  and Slave mode (details for these procedures are available in reference manual
  (RM0033)).
  
@endverbatim
  * @{
  */

/**
  * @brief  Deinitialize the SPIx peripheral registers to their default reset values.
  * @param  SPIx: To select the SPIx/I2Sx peripheral, where x can be: 1, 2 or 3 
  *         in SPI mode or 2 or 3 in I2S mode.   
  * @retval None
  */
void SPI_I2S_DeInit(SPI_TypeDef* SPIx)
{
  /* Check the parameters */
  assert_param(IS_SPI_ALL_PERIPH(SPIx));

  if (SPIx == SPI1)
  {
    /* Enable SPI1 reset state */
    RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1, ENABLE);
    /* Release SPI1 from reset state */
    RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1, DISABLE);
  }
  else if (SPIx == SPI2)
  {
    /* Enable SPI2 reset state */
    RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI2, ENABLE);
    /* Release SPI2 from reset state */
    RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI2, DISABLE);
    }
  else
  {
    if (SPIx == SPI3)
    {
      /* Enable SPI3 reset state */
      RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI3, ENABLE);
      /* Release SPI3 from reset state */
      RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI3, DISABLE);
    }
  }
}

/**
  * @brief  Initializes the SPIx peripheral according to the specified 
  *         parameters in the SPI_InitStruct.
  * @param  SPIx: where x can be 1, 2 or 3 to select the SPI peripheral.
  * @param  SPI_InitStruct: pointer to a SPI_InitTypeDef structure that
  *         contains the configuration information for the specified SPI peripheral.
  * @retval None
  */
void SPI_Init(SPI_TypeDef* SPIx, SPI_InitTypeDef* SPI_InitStruct)
{
  uint16_t tmpreg = 0;
  
  /* check the parameters */
  assert_param(IS_SPI_ALL_PERIPH(SPIx));
  
  /* Check the SPI parameters */
  assert_param(IS_SPI_DIRECTION_MODE(SPI_InitStruct->SPI_Direction));
  assert_param(IS_SPI_MODE(SPI_InitStruct->SPI_Mode));
  assert_param(IS_SPI_DATASIZE(SPI_InitStruct->SPI_DataSize));
  assert_param(IS_SPI_CPOL(SPI_InitStruct->SPI_CPOL));
  assert_param(IS_SPI_CPHA(SPI_InitStruct->SPI_CPHA));
  assert_param(IS_SPI_NSS(SPI_InitStruct->SPI_NSS));
  assert_param(IS_SPI_BAUDRATE_PRESCALER(SPI_InitStruct->SPI_BaudRatePrescaler));
  assert_param(IS_SPI_FIRST_BIT(SPI_InitStruct->SPI_FirstBit));
  assert_param(IS_SPI_CRC_POLYNOMIAL(SPI_InitStruct->SPI_CRCPolynomial));

/*---------------------------- SPIx CR1 Configuration ------------------------*/
  /* Get the SPIx CR1 value */
  tmpreg = SPIx->CR1;
  /* Clear BIDIMode, BIDIOE, RxONLY, SSM, SSI, LSBFirst, BR, MSTR, CPOL and CPHA bits */
  tmpreg &= CR1_CLEAR_MASK;
  /* Configure SPIx: direction, NSS management, first transmitted bit, BaudRate prescaler
     master/salve mode, CPOL and CPHA */
  /* Set BIDImode, BIDIOE and RxONLY bits according to SPI_Direction value */
  /* Set SSM, SSI and MSTR bits according to SPI_Mode and SPI_NSS values */
  /* Set LSBFirst bit according to SPI_FirstBit value */
  /* Set BR bits according to SPI_BaudRatePrescaler value */
  /* Set CPOL bit according to SPI_CPOL value */
  /* Set CPHA bit according to SPI_CPHA value */
  tmpreg |= (uint16_t)((uint32_t)SPI_InitStruct->SPI_Direction | SPI_InitStruct->SPI_Mode |
                  SPI_InitStruct->SPI_DataSize | SPI_InitStruct->SPI_CPOL |  
                  SPI_InitStruct->SPI_CPHA | SPI_InitStruct->SPI_NSS |  
                  SPI_InitStruct->SPI_BaudRatePrescaler | SPI_InitStruct->SPI_FirstBit);
  /* Write to SPIx CR1 */
  SPIx->CR1 = tmpreg;

  /* Activate the SPI mode (Reset I2SMOD bit in I2SCFGR register) */
  SPIx->I2SCFGR &= (uint16_t)~((uint16_t)SPI_I2SCFGR_I2SMOD);
/*---------------------------- SPIx CRCPOLY Configuration --------------------*/
  /* Write to SPIx CRCPOLY */
  SPIx->CRCPR = SPI_InitStruct->SPI_CRCPolynomial;
}

/**
  * @brief  Initializes the SPIx peripheral according to the specified 
  *         parameters in the I2S_InitStruct.
  * @param  SPIx: where x can be  2 or 3 to select the SPI peripheral (configured in I2S mode).
  * @param  I2S_InitStruct: pointer to an I2S_InitTypeDef structure that
  *         contains the configuration information for the specified SPI peripheral
  *         configured in I2S mode.
  *           
  * @note   The function calculates the optimal prescaler needed to obtain the most 
  *         accurate audio frequency (depending on the I2S clock source, the PLL values 
  *         and the product configuration). But in case the prescaler value is greater 
  *         than 511, the default value (0x02) will be configured instead.    
  * 
  * @note   if an external clock is used as source clock for the I2S, then the define
  *         I2S_EXTERNAL_CLOCK_VAL in file stm32f2xx_conf.h should be enabled and set
  *         to the value of the the source clock frequency (in Hz).
  *  
  * @retval None
  */
void I2S_Init(SPI_TypeDef* SPIx, I2S_InitTypeDef* I2S_InitStruct)
{
  uint16_t tmpreg = 0, i2sdiv = 2, i2sodd = 0, packetlength = 1;
  uint32_t tmp = 0, i2sclk = 0;
#ifndef I2S_EXTERNAL_CLOCK_VAL
  uint32_t pllm = 0, plln = 0, pllr = 0;
#endif /* I2S_EXTERNAL_CLOCK_VAL */
  
  /* Check the I2S parameters */
  assert_param(IS_SPI_23_PERIPH(SPIx));
  assert_param(IS_I2S_MODE(I2S_InitStruct->I2S_Mode));
  assert_param(IS_I2S_STANDARD(I2S_InitStruct->I2S_Standard));
  assert_param(IS_I2S_DATA_FORMAT(I2S_InitStruct->I2S_DataFormat));
  assert_param(IS_I2S_MCLK_OUTPUT(I2S_InitStruct->I2S_MCLKOutput));
  assert_param(IS_I2S_AUDIO_FREQ(I2S_InitStruct->I2S_AudioFreq));
  assert_param(IS_I2S_CPOL(I2S_InitStruct->I2S_CPOL));  

/*----------------------- SPIx I2SCFGR & I2SPR Configuration -----------------*/
  /* Clear I2SMOD, I2SE, I2SCFG, PCMSYNC, I2SSTD, CKPOL, DATLEN and CHLEN bits */
  SPIx->I2SCFGR &= I2SCFGR_CLEAR_MASK; 
  SPIx->I2SPR = 0x0002;