stm3210c_eval_lcd.c

STM32的SPI1与SPI2通信

  LCD_WriteReg(LCD_REG_83, Ypos);
  LCD_SetCursor(Xpos, Ypos);
}


/**
  * @brief  Disables LCD Window mode.
  * @param  None
  * @retval None
  */
void LCD_WindowModeDisable(void)
{
  LCD_SetDisplayWindow(239, 0x13F, 240, 320);
  LCD_WriteReg(LCD_REG_3, 0x1018);    
}


/**
  * @brief  Displays a line.
  * @param  Xpos: specifies the X position.
  * @param  Ypos: specifies the Y position.
  * @param  Length: line length.
  * @param  Direction: line direction.
  *   This parameter can be one of the following values: Vertical or Horizontal.
  * @retval None
  */
void LCD_DrawLine(uint8_t Xpos, uint16_t Ypos, uint16_t Length, uint8_t Direction)
{
  uint32_t i = 0;
  
  LCD_SetCursor(Xpos, Ypos);
  if(Direction == LCD_DIR_HORIZONTAL)
  { 
    LCD_WriteRAM_Prepare(); /* Prepare to write GRAM */
    for(i = 0; i < Length; i++)
    {
      LCD_WriteRAM(TextColor);
    }
    LCD_CtrlLinesWrite(LCD_NCS_GPIO_PORT, LCD_NCS_PIN, Bit_SET);
  }
  else
  {
    for(i = 0; i < Length; i++)
    {
      LCD_WriteRAMWord(TextColor);
      Xpos++;
      LCD_SetCursor(Xpos, Ypos);
    }
  }
}


/**
  * @brief  Displays a rectangle.
  * @param  Xpos: specifies the X position.
  * @param  Ypos: specifies the Y position.
  * @param  Height: display rectangle height.
  * @param  Width: display rectangle width.
  * @retval None
  */
void LCD_DrawRect(uint8_t Xpos, uint16_t Ypos, uint8_t Height, uint16_t Width)
{
  LCD_DrawLine(Xpos, Ypos, Width, LCD_DIR_HORIZONTAL);
  LCD_DrawLine((Xpos + Height), Ypos, Width, LCD_DIR_HORIZONTAL);
  
  LCD_DrawLine(Xpos, Ypos, Height, LCD_DIR_VERTICAL);
  LCD_DrawLine(Xpos, (Ypos - Width + 1), Height, LCD_DIR_VERTICAL);
}


/**
  * @brief  Displays a circle.
  * @param  Xpos: specifies the X position.
  * @param  Ypos: specifies the Y position.
  * @param  Radius
  * @retval None
  */
void LCD_DrawCircle(uint8_t Xpos, uint16_t Ypos, uint16_t Radius)
{
  s32  D;/* Decision Variable */ 
  uint32_t  CurX;/* Current X Value */
  uint32_t  CurY;/* Current Y Value */ 
  
  D = 3 - (Radius << 1);
  CurX = 0;
  CurY = Radius;
  
  while (CurX <= CurY)
  {
    LCD_SetCursor(Xpos + CurX, Ypos + CurY);
    LCD_WriteRAMWord(TextColor);
    LCD_SetCursor(Xpos + CurX, Ypos - CurY);
    LCD_WriteRAMWord(TextColor);
    LCD_SetCursor(Xpos - CurX, Ypos + CurY);
    LCD_WriteRAMWord(TextColor);
    LCD_SetCursor(Xpos - CurX, Ypos - CurY);
    LCD_WriteRAMWord(TextColor);
    LCD_SetCursor(Xpos + CurY, Ypos + CurX);
    LCD_WriteRAMWord(TextColor);
    LCD_SetCursor(Xpos + CurY, Ypos - CurX);
    LCD_WriteRAMWord(TextColor);
    LCD_SetCursor(Xpos - CurY, Ypos + CurX);
    LCD_WriteRAMWord(TextColor);
    LCD_SetCursor(Xpos - CurY, Ypos - CurX);
    LCD_WriteRAMWord(TextColor);
    if (D < 0)
    { 
      D += (CurX << 2) + 6;
    }
    else
    {
      D += ((CurX - CurY) << 2) + 10;
      CurY--;
    }
    CurX++;
  }
}

/**
  * @brief  Displays a monocolor picture.
  * @param  Pict: pointer to the picture array.
  * @retval None
  */
void LCD_DrawMonoPict(const uint32_t *Pict)
{
  uint32_t index = 0, i = 0;
  LCD_SetCursor(0, (LCD_PIXEL_WIDTH - 1)); 
  LCD_WriteRAM_Prepare(); /* Prepare to write GRAM */
  for(index = 0; index < 2400; index++)
  {
    for(i = 0; i < 32; i++)
    {
      if((Pict[index] & (1 << i)) == 0x00)
      {
        LCD_WriteRAM(BackColor);
      }
      else
      {
        LCD_WriteRAM(TextColor);
      }
    }
  }
  LCD_CtrlLinesWrite(LCD_NCS_GPIO_PORT, LCD_NCS_PIN, Bit_SET);
}

#ifdef USE_LCD_DrawBMP
/**
  * @brief  Displays a bitmap picture loaded in the SPI Flash.
  * @param  BmpAddress: Bmp picture address in the SPI Flash.
  * @retval None
  */
//void LCD_DrawBMP(uint32_t BmpAddress)
//{
//  uint32_t i = 0, size = 0;
//
//  /* Read bitmap size */
//  sFLASH_ReadBuffer((uint8_t*)&size, BmpAddress + 2, 4);
//
//  /* get bitmap data address offset */
//  sFLASH_ReadBuffer((uint8_t*)&i, BmpAddress + 10, 4);
//  
//  size = (size - i)/2;
//
//  sFLASH_StartReadSequence(BmpAddress + i);
//
//  /* Disable LCD_SPI  */
//  SPI_Cmd(LCD_SPI, DISABLE);
//  /* SPI in 16-bit mode */
//  SPI_DataSizeConfig(LCD_SPI, SPI_DataSize_16b);
//
//  /* Enable LCD_SPI  */
//  SPI_Cmd(LCD_SPI, ENABLE);
//  
//  /* Set GRAM write direction and BGR = 1 */
//  /* I/D=00 (Horizontal : decrement, Vertical : decrement) */
//  /* AM=1 (address is updated in vertical writing direction) */
//  LCD_WriteReg(LCD_REG_3, 0x1008);
//
//  LCD_WriteRAM_Prepare(); /* Prepare to write GRAM */
//
//  /* Read bitmap data from SPI Flash and send them to LCD */
//  for(i = 0; i < size; i++)
//  {
//    LCD_WriteRAM(__REV_HalfWord(sFLASH_SendHalfWord(0xA5A5)));
//  }
//
//  LCD_CtrlLinesWrite(LCD_NCS_GPIO_PORT, LCD_NCS_PIN, Bit_SET);
//
//  /* Deselect the FLASH: Chip Select high */
//  sFLASH_CS_HIGH();
//
//  /* Disable LCD_SPI  */
//  SPI_Cmd(LCD_SPI, DISABLE);
//  /* SPI in 8-bit mode */
//  SPI_DataSizeConfig(LCD_SPI, SPI_DataSize_8b);
//
//  /* Enable LCD_SPI  */
//  SPI_Cmd(LCD_SPI, ENABLE);
//
//  /* Set GRAM write direction and BGR = 1 */
//  /* I/D = 01 (Horizontal : increment, Vertical : decrement) */
//  /* AM = 1 (address is updated in vertical writing direction) */
//  LCD_WriteReg(LCD_REG_3, 0x1018);
//}


/**
  * @brief  Displays a bitmap picture loaded in the Internal FLASH.
  * @param  BmpAddress: Bmp picture address in the Internal FLASH.
  * @retval None
  */
void LCD_DrawBMP(const uint16_t *BmpAddress)
{
  uint32_t i = 0, size = 0;
  /* Read bitmap size */
  size = BmpAddress[1] | (BmpAddress[2] << 16);
  /* get bitmap data address offset */
  i = BmpAddress[5] | (BmpAddress[6] << 16);
  size = (size - i)/2;
  BmpAddress += i/2;
  /* Set GRAM write direction and BGR = 1 */
  /* I/D=00 (Horizontal : decrement, Vertical : decrement) */
  /* AM=1 (address is updated in vertical writing direction) */
  LCD_WriteReg(LCD_REG_3, 0x1008);
  LCD_WriteRAM_Prepare(); /* Prepare to write GRAM */
  /* Read bitmap data from SPI Flash and send them to LCD */
  for(i = 0; i < size; i++)
  {
    LCD_WriteRAM(BmpAddress[i]);
  }
  LCD_CtrlLinesWrite(LCD_NCS_GPIO_PORT, LCD_NCS_PIN, Bit_SET);
  /* Set GRAM write direction and BGR = 1 */
  /* I/D = 01 (Horizontal : increment, Vertical : decrement) */
  /* AM = 1 (address is updated in vertical writing direction) */
  LCD_WriteReg(LCD_REG_3, 0x1018);
}
#endif

/**
  * @brief  Displays a full rectangle.
  * @param  Xpos: specifies the X position.
  * @param  Ypos: specifies the Y position.
  * @param  Height: rectangle height.
  * @param  Width: rectangle width.
  * @retval None
  */
void LCD_DrawFullRect(uint16_t Xpos, uint16_t Ypos, uint16_t Width, uint16_t Height)
{
  LCD_SetTextColor(TextColor);

  LCD_DrawLine(Xpos, Ypos, Width, LCD_DIR_HORIZONTAL);
  LCD_DrawLine((Xpos + Height), Ypos, Width, LCD_DIR_HORIZONTAL);
  
  LCD_DrawLine(Xpos, Ypos, Height, LCD_DIR_VERTICAL);
  LCD_DrawLine(Xpos, (Ypos - Width + 1), Height, LCD_DIR_VERTICAL);

  Width -= 2;
  Height--;
  Ypos--;

  LCD_SetTextColor(BackColor);

  while(Height--)
  {
    LCD_DrawLine(++Xpos, Ypos, Width, LCD_DIR_HORIZONTAL);    
  }

  LCD_SetTextColor(TextColor);
}

/**
  * @brief  Displays a full circle.
  * @param  Xpos: specifies the X position.
  * @param  Ypos: specifies the Y position.
  * @param  Radius
  * @retval None
  */
void LCD_DrawFullCircle(uint16_t Xpos, uint16_t Ypos, uint16_t Radius)
{
  int32_t  D;    /* Decision Variable */ 
  uint32_t  CurX;/* Current X Value */
  uint32_t  CurY;/* Current Y Value */ 
  
  D = 3 - (Radius << 1);

  CurX = 0;
  CurY = Radius;
  
  LCD_SetTextColor(BackColor);

  while (CurX <= CurY)
  {
    if(CurY > 0) 
    {
      LCD_DrawLine(Xpos - CurX, Ypos + CurY, 2*CurY, LCD_DIR_HORIZONTAL);
      LCD_DrawLine(Xpos + CurX, Ypos + CurY, 2*CurY, LCD_DIR_HORIZONTAL);
    }

    if(CurX > 0) 
    {
      LCD_DrawLine(Xpos - CurY, Ypos + CurX, 2*CurX, LCD_DIR_HORIZONTAL);
      LCD_DrawLine(Xpos + CurY, Ypos + CurX, 2*CurX, LCD_DIR_HORIZONTAL);
    }
    if (D < 0)
    { 
      D += (CurX << 2) + 6;
    }
    else
    {
      D += ((CurX - CurY) << 2) + 10;
      CurY--;
    }
    CurX++;
  }

  LCD_SetTextColor(TextColor);
  LCD_DrawCircle(Xpos, Ypos, Radius);
}

/**
  * @brief  Displays an uni line (between two points).
  * @param  x1: specifies the point 1 x position.
  * @param  y1: specifies the point 1 y position.
  * @param  x2: specifies the point 2 x position.
  * @param  y2: specifies the point 2 y position.
  * @retval None
  */
void LCD_DrawUniLine(uint16_t x1, uint16_t y1, uint16_t x2, uint16_t y2)
{
  int16_t deltax = 0, deltay = 0, x = 0, y = 0, xinc1 = 0, xinc2 = 0, 
  yinc1 = 0, yinc2 = 0, den = 0, num = 0, numadd = 0, numpixels = 0, 
  curpixel = 0;
  
  deltax = ABS(x2 - x1);        /* The difference between the x's */
  deltay = ABS(y2 - y1);        /* The difference between the y's */
  x = x1;                       /* Start x off at the first pixel */
  y = y1;                       /* Start y off at the first pixel */
  
  if (x2 >= x1)                 /* The x-values are increasing */
  {
    xinc1 = 1;
    xinc2 = 1;
  }
  else                          /* The x-values are decreasing */
  {
    xinc1 = -1;
    xinc2 = -1;
  }
  
  if (y2 >= y1)                 /* The y-values are increasing */
  {
    yinc1 = 1;
    yinc2 = 1;
  }
  else                          /* The y-values are decreasing */
  {
    yinc1 = -1;
    yinc2 = -1;
  }
  
  if (deltax >= deltay)         /* There is at least one x-value for every y-value */
  {
    xinc1 = 0;                  /* Don't change the x when numerator >= denominator */
    yinc2 = 0;                  /* Don't change the y for every iteration */
    den = deltax;
    num = deltax / 2;
    numadd = deltay;
    numpixels = deltax;         /* There are more x-values than y-values */
  }
  else                          /* There is at least one y-value for every x-value */
  {
    xinc2 = 0;                  /* Don't change the x for every iteration */
    yinc1 = 0;                  /* Don't change the y when numerator >= denominator */
    den = deltay;
    num = deltay / 2;
    numadd = deltax;
    numpixels = deltay;         /* There are more y-values than x-values */
  }
  
  for (curpixel = 0; curpixel <= numpixels; curpixel++)
  {
    PutPixel(x, y);             /* Draw the current pixel */
    num += numadd;              /* Increase the numerator by the top of the fraction */
    if (num >= den)             /* Check if numerator >= denominator */
    {
      num -= den;               /* Calculate the new numerator value */
      x += xinc1;               /* Change the x as appropriate */
      y += yinc1;               /* Change the y as appropriate */
    }
    x += xinc2;                 /* Change the x as appropriate */
    y += yinc2;                 /* Change the y as appropriate */
  }
}

/**
  * @brief  Displays an polyline (between many points).
  * @param  Points: pointer to the points array.
  * @param  PointCount: Number of points.
  * @retval None
  */
void LCD_PolyLine(pPoint Points, uint16_t PointCount)
{
  int16_t X = 0, Y = 0;

  if(PointCount < 2)
  {
    return;
  }

  while(--PointCount)
  {
    X = Points->X;
    Y = Points->Y;
    Points++;
    LCD_DrawUniLine(X, Y, Points->X, Points->Y);
  }
}

/**
  * @brief  Displays an relative polyline (between many points).
  * @param  Points: pointer to the points array.
  * @param  PointCount: Number of points.
  * @param  Closed: specifies if the draw is closed or not.
  *           1: closed, 0 : not closed.
  * @retval None
  */
static void LCD_PolyLineRelativeClosed(pPoint Points, uint16_t PointCount, uint16_t Closed)
{
  int16_t X = 0, Y = 0;
  pPoint First = Points;

  if(PointCount < 2)
  {
    return;
  }  
  X = Points->X;
  Y = Points->Y;
  while(--PointCount)
  {
    Points++;
    LCD_DrawUniLine(X, Y, X + Points->X, Y + Points->Y);
    X = X + Points->X;
    Y = Y + Points->Y;
  }
  if(Closed)
  {
    LCD_DrawUniLine(First->X, First->Y, X, Y);
  }  
}

/**
  * @brief  Displays a closed polyline (between many points).
  * @param  Points: pointer to the points array.
  * @param  PointCount: Number of points.
  * @retval None
  */
void LCD_ClosedPolyLine(pPoint Points, uint16_t PointCount)
{
  LCD_PolyLine(Points, PointCount);
  LCD_DrawUniLine(Points->X, Points->Y, (Points+PointCount-1)->X, (Points+PointCount-1)->Y);
}

/**
  * @brief  Displays a relative polyline (between many points).
  * @param  Points: pointer to the points array.
  * @param  PointCount: Number of points.
  * @retval None
  */
void LCD_PolyLineRelative(pPoint Points, uint16_t PointCount)
{