stm3210c_eval.c

STM32的SPI1与SPI2通信

  *   contains the configuration information for the specified USART peripheral.
  * @retval None
  */
void STM_EVAL_COMInit(COM_TypeDef COM, USART_InitTypeDef* USART_InitStruct)
{
  GPIO_InitTypeDef GPIO_InitStructure;

  /* Enable GPIO clock */
  RCC_APB2PeriphClockCmd(COM_TX_PORT_CLK[COM] | COM_RX_PORT_CLK[COM] | RCC_APB2Periph_AFIO, ENABLE);

  if (COM == COM1)
  {
    /* Enable the USART2 Pins Software Remapping */
    GPIO_PinRemapConfig(GPIO_Remap_USART2, ENABLE);
    RCC_APB1PeriphClockCmd(COM_USART_CLK[COM], ENABLE);
  }

  /* Configure USART Tx as alternate function push-pull */
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
  GPIO_InitStructure.GPIO_Pin = COM_TX_PIN[COM];
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_Init(COM_TX_PORT[COM], &GPIO_InitStructure);

  /* Configure USART Rx as input floating */
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
  GPIO_InitStructure.GPIO_Pin = COM_RX_PIN[COM];
  GPIO_Init(COM_RX_PORT[COM], &GPIO_InitStructure);

  /* USART configuration */
  USART_Init(COM_USART[COM], USART_InitStruct);
    
  /* Enable USART */
  USART_Cmd(COM_USART[COM], ENABLE);
}

/**
  * @brief  DeInitializes the SD/SD communication.
  * @param  None
  * @retval None
  */
void SD_LowLevel_DeInit(void)
{
  GPIO_InitTypeDef  GPIO_InitStructure;
  
  SPI_Cmd(SD_SPI, DISABLE); /*!< SD_SPI disable */
  SPI_I2S_DeInit(SD_SPI);   /*!< DeInitializes the SD_SPI */
  
  /*!< SD_SPI Periph clock disable */
  RCC_APB1PeriphClockCmd(SD_SPI_CLK, DISABLE);
  /*!< DeRemap SPI3 Pins */
  GPIO_PinRemapConfig(GPIO_Remap_SPI3, DISABLE);  
  
  /*!< Configure SD_SPI pins: SCK */
  GPIO_InitStructure.GPIO_Pin = SD_SPI_SCK_PIN;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
  GPIO_Init(SD_SPI_SCK_GPIO_PORT, &GPIO_InitStructure);

  /*!< Configure SD_SPI pins: MISO */
  GPIO_InitStructure.GPIO_Pin = SD_SPI_MISO_PIN;
  GPIO_Init(SD_SPI_MISO_GPIO_PORT, &GPIO_InitStructure);

  /*!< Configure SD_SPI pins: MOSI */
  GPIO_InitStructure.GPIO_Pin = SD_SPI_MOSI_PIN;
  GPIO_Init(SD_SPI_MOSI_GPIO_PORT, &GPIO_InitStructure);

  /*!< Configure SD_SPI_CS_PIN pin: SD Card CS pin */
  GPIO_InitStructure.GPIO_Pin = SD_CS_PIN;
  GPIO_Init(SD_CS_GPIO_PORT, &GPIO_InitStructure);

  /*!< Configure SD_SPI_DETECT_PIN pin: SD Card detect pin */
  GPIO_InitStructure.GPIO_Pin = SD_DETECT_PIN;
  GPIO_Init(SD_DETECT_GPIO_PORT, &GPIO_InitStructure);
}

/**
  * @brief  Initializes the SD_SPI and CS pins.
  * @param  None
  * @retval None
  */
void SD_LowLevel_Init(void)
{
  GPIO_InitTypeDef  GPIO_InitStructure;
  SPI_InitTypeDef   SPI_InitStructure;

  /*!< SD_SPI_CS_GPIO, SD_SPI_MOSI_GPIO, SD_SPI_MISO_GPIO, SD_SPI_DETECT_GPIO 
       and SD_SPI_SCK_GPIO Periph clock enable */
  RCC_APB2PeriphClockCmd(SD_CS_GPIO_CLK | SD_SPI_MOSI_GPIO_CLK | SD_SPI_MISO_GPIO_CLK |
                         SD_SPI_SCK_GPIO_CLK | SD_DETECT_GPIO_CLK, ENABLE);

  /*!< SD_SPI Periph clock enable */
  RCC_APB1PeriphClockCmd(SD_SPI_CLK, ENABLE);
  /*!< AFIO Periph clock enable */
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);
  /*!< Remap SPI3 Pins */
  GPIO_PinRemapConfig(GPIO_Remap_SPI3,ENABLE);  
  
  /*!< Configure SD_SPI pins: SCK */
  GPIO_InitStructure.GPIO_Pin = SD_SPI_SCK_PIN;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
  GPIO_Init(SD_SPI_SCK_GPIO_PORT, &GPIO_InitStructure);

  /*!< Configure SD_SPI pins: MOSI */
  GPIO_InitStructure.GPIO_Pin = SD_SPI_MOSI_PIN;
  GPIO_Init(SD_SPI_MOSI_GPIO_PORT, &GPIO_InitStructure);

  /*!< Configure SD_SPI pins: MISO */
  GPIO_InitStructure.GPIO_Pin = SD_SPI_MISO_PIN;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;  
  GPIO_Init(SD_SPI_MISO_GPIO_PORT, &GPIO_InitStructure);
  
  /*!< Configure SD_SPI_CS_PIN pin: SD Card CS pin */
  GPIO_InitStructure.GPIO_Pin = SD_CS_PIN;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
  GPIO_Init(SD_CS_GPIO_PORT, &GPIO_InitStructure);

  /*!< Configure SD_SPI_DETECT_PIN pin: SD Card detect pin */
  GPIO_InitStructure.GPIO_Pin = SD_DETECT_PIN;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
  GPIO_Init(SD_DETECT_GPIO_PORT, &GPIO_InitStructure);

  /*!< SD_SPI Config */
  SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex;
  SPI_InitStructure.SPI_Mode = SPI_Mode_Master;
  SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b;
  SPI_InitStructure.SPI_CPOL = SPI_CPOL_High;
  SPI_InitStructure.SPI_CPHA = SPI_CPHA_2Edge;
  SPI_InitStructure.SPI_NSS = SPI_NSS_Soft;
  SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_2;
  SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB;
  SPI_InitStructure.SPI_CRCPolynomial = 7;
  SPI_Init(SD_SPI, &SPI_InitStructure);
  
  SPI_Cmd(SD_SPI, ENABLE); /*!< SD_SPI enable */
}

/**
  * @brief  DeInitializes peripherals used by the I2C EEPROM driver.
  * @param  None
  * @retval None
  */
void sEE_LowLevel_DeInit(void)
{
  GPIO_InitTypeDef  GPIO_InitStructure; 
  NVIC_InitTypeDef NVIC_InitStructure;    
   
  /* sEE_I2C Peripheral Disable */
  I2C_Cmd(sEE_I2C, DISABLE);
 
  /* sEE_I2C DeInit */
  I2C_DeInit(sEE_I2C);

  /*!< sEE_I2C Periph clock disable */
  RCC_APB1PeriphClockCmd(sEE_I2C_CLK, DISABLE);
    
  /*!< GPIO configuration */  
  /*!< Configure sEE_I2C pins: SCL */
  GPIO_InitStructure.GPIO_Pin = sEE_I2C_SCL_PIN;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
  GPIO_Init(sEE_I2C_SCL_GPIO_PORT, &GPIO_InitStructure);

  /*!< Configure sEE_I2C pins: SDA */
  GPIO_InitStructure.GPIO_Pin = sEE_I2C_SDA_PIN;
  GPIO_Init(sEE_I2C_SDA_GPIO_PORT, &GPIO_InitStructure);
  
  /* Configure and enable I2C DMA TX Channel interrupt */
  NVIC_InitStructure.NVIC_IRQChannel = sEE_I2C_DMA_TX_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = sEE_I2C_DMA_PREPRIO;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = sEE_I2C_DMA_SUBPRIO;
  NVIC_InitStructure.NVIC_IRQChannelCmd = DISABLE;
  NVIC_Init(&NVIC_InitStructure);

  /* Configure and enable I2C DMA RX Channel interrupt */
  NVIC_InitStructure.NVIC_IRQChannel = sEE_I2C_DMA_RX_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = sEE_I2C_DMA_PREPRIO;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = sEE_I2C_DMA_SUBPRIO;
  NVIC_Init(&NVIC_InitStructure);   
  
  /* Disable and Deinitialize the DMA channels */
  DMA_Cmd(sEE_I2C_DMA_CHANNEL_TX, DISABLE);
  DMA_Cmd(sEE_I2C_DMA_CHANNEL_RX, DISABLE);
  DMA_DeInit(sEE_I2C_DMA_CHANNEL_TX);
  DMA_DeInit(sEE_I2C_DMA_CHANNEL_RX);
}

/**
  * @brief  Initializes peripherals used by the I2C EEPROM driver.
  * @param  None
  * @retval None
  */
void sEE_LowLevel_Init(void)
{
  GPIO_InitTypeDef  GPIO_InitStructure;
  NVIC_InitTypeDef NVIC_InitStructure;  
    
  /*!< sEE_I2C_SCL_GPIO_CLK and sEE_I2C_SDA_GPIO_CLK Periph clock enable */
  RCC_APB2PeriphClockCmd(sEE_I2C_SCL_GPIO_CLK | sEE_I2C_SDA_GPIO_CLK, ENABLE);

  /*!< sEE_I2C Periph clock enable */
  RCC_APB1PeriphClockCmd(sEE_I2C_CLK, ENABLE);
    
  /*!< GPIO configuration */  
  /*!< Configure sEE_I2C pins: SCL */
  GPIO_InitStructure.GPIO_Pin = sEE_I2C_SCL_PIN;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_OD;
  GPIO_Init(sEE_I2C_SCL_GPIO_PORT, &GPIO_InitStructure);

  /*!< Configure sEE_I2C pins: SDA */
  GPIO_InitStructure.GPIO_Pin = sEE_I2C_SDA_PIN;
  GPIO_Init(sEE_I2C_SDA_GPIO_PORT, &GPIO_InitStructure); 

  /* Configure and enable I2C DMA TX Channel interrupt */
  NVIC_InitStructure.NVIC_IRQChannel = sEE_I2C_DMA_TX_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = sEE_I2C_DMA_PREPRIO;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = sEE_I2C_DMA_SUBPRIO;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);

  /* Configure and enable I2C DMA RX Channel interrupt */
  NVIC_InitStructure.NVIC_IRQChannel = sEE_I2C_DMA_RX_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = sEE_I2C_DMA_PREPRIO;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = sEE_I2C_DMA_SUBPRIO;
  NVIC_Init(&NVIC_InitStructure);  
  
  /*!< I2C DMA TX and RX channels configuration */
  /* Enable the DMA clock */
  RCC_AHBPeriphClockCmd(sEE_I2C_DMA_CLK, ENABLE);

  /* I2C TX DMA Channel configuration */
  DMA_DeInit(sEE_I2C_DMA_CHANNEL_TX);
  sEEDMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)sEE_I2C_DR_Address;
  sEEDMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)0;   /* This parameter will be configured durig communication */
  sEEDMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST;    /* This parameter will be configured durig communication */
  sEEDMA_InitStructure.DMA_BufferSize = 0xFFFF;            /* This parameter will be configured durig communication */
  sEEDMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
  sEEDMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
  sEEDMA_InitStructure.DMA_PeripheralDataSize = DMA_MemoryDataSize_Byte;
  sEEDMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte;
  sEEDMA_InitStructure.DMA_Mode = DMA_Mode_Normal;
  sEEDMA_InitStructure.DMA_Priority = DMA_Priority_VeryHigh;
  sEEDMA_InitStructure.DMA_M2M = DMA_M2M_Disable;
  DMA_Init(sEE_I2C_DMA_CHANNEL_TX, &sEEDMA_InitStructure);  
  
  /* I2C RX DMA Channel configuration */
  DMA_DeInit(sEE_I2C_DMA_CHANNEL_RX);
  DMA_Init(sEE_I2C_DMA_CHANNEL_RX, &sEEDMA_InitStructure);  
  
  /* Enable the DMA Channels Interrupts */
  DMA_ITConfig(sEE_I2C_DMA_CHANNEL_TX, DMA_IT_TC, ENABLE);
  DMA_ITConfig(sEE_I2C_DMA_CHANNEL_RX, DMA_IT_TC, ENABLE);    
}


/**
  * @brief  Initializes DMA channel used by the I2C EEPROM driver.
  * @param  None
  * @retval None
  */
void sEE_LowLevel_DMAConfig(uint32_t pBuffer, uint32_t BufferSize, uint32_t Direction)
{ 
  /* Initialize the DMA with the new parameters */
  if (Direction == sEE_DIRECTION_TX)
  {
    /* Configure the DMA Tx Channel with the buffer address and the buffer size */
    sEEDMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)pBuffer;
    sEEDMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST;    
    sEEDMA_InitStructure.DMA_BufferSize = (uint32_t)BufferSize;  
    DMA_Init(sEE_I2C_DMA_CHANNEL_TX, &sEEDMA_InitStructure);  
  }
  else
  { 
    /* Configure the DMA Rx Channel with the buffer address and the buffer size */
    sEEDMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)pBuffer;
    sEEDMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
    sEEDMA_InitStructure.DMA_BufferSize = (uint32_t)BufferSize;      
    DMA_Init(sEE_I2C_DMA_CHANNEL_RX, &sEEDMA_InitStructure);    
  }
}

/**
  * @}
  */ 

/**
  * @}
  */ 

/**
  * @}
  */ 

/**
  * @}
  */   

/**
  * @}
  */ 
    
/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/