stm32f0xx_dma.c

stm32f0固件库

  *         1 to 5 for DMA1 to select the DMA Channel.
  * @param  DataNumber: The number of data units in the current DMAy Channelx
  *         transfer.
  * @note   This function can only be used when the DMAy_Channelx is disabled.
  * @retval None.
  */
void DMA_SetCurrDataCounter(DMA_Channel_TypeDef* DMAy_Channelx, uint16_t DataNumber)
{
  /* Check the parameters */
  assert_param(IS_DMA_ALL_PERIPH(DMAy_Channelx));

/*--------------------------- DMAy Channelx CNDTR Configuration --------------*/
  /* Write to DMAy Channelx CNDTR */
  DMAy_Channelx->CNDTR = DataNumber;
}

/**
  * @brief  Returns the number of remaining data units in the current
  *         DMAy Channelx transfer.
  * @param  DMAy_Channelx: where y can be 1 to select the DMA and
  *         x can be 1 to 5 for DMA1 to select the DMA Channel.
  * @retval The number of remaining data units in the current DMAy Channelx
  *         transfer.
  */
uint16_t DMA_GetCurrDataCounter(DMA_Channel_TypeDef* DMAy_Channelx)
{
  /* Check the parameters */
  assert_param(IS_DMA_ALL_PERIPH(DMAy_Channelx));
  /* Return the number of remaining data units for DMAy Channelx */
  return ((uint16_t)(DMAy_Channelx->CNDTR));
}

/**
  * @}
  */

/** @defgroup DMA_Group3 Interrupts and flags management functions
 *  @brief   Interrupts and flags management functions 
 *
@verbatim
 ===============================================================================
          ##### Interrupts and flags management functions #####
 ===============================================================================
    [..] This subsection provides functions allowing to configure the DMA Interrupts 
         sources and check or clear the flags or pending bits status.
         The user should identify which mode will be used in his application to manage 
         the DMA controller events: Polling mode or Interrupt mode. 
  *** Polling Mode ***
  ====================
    [..] Each DMA channel can be managed through 4 event Flags:(y : DMA Controller 
         number  x : DMA channel number ).
         (#) DMAy_FLAG_TCx : to indicate that a Transfer Complete event occurred.
         (#) DMAy_FLAG_HTx : to indicate that a Half-Transfer Complete event occurred.
         (#) DMAy_FLAG_TEx : to indicate that a Transfer Error occurred.
         (#) DMAy_FLAG_GLx : to indicate that at least one of the events described 
             above occurred.
    -@- Clearing DMAy_FLAG_GLx results in clearing all other pending flags of the 
        same channel (DMAy_FLAG_TCx, DMAy_FLAG_HTx and DMAy_FLAG_TEx).
    [..]In this Mode it is advised to use the following functions:
        (+) FlagStatus DMA_GetFlagStatus(uint32_t DMA_FLAG);
        (+) void DMA_ClearFlag(uint32_t DMA_FLAG);

  *** Interrupt Mode ***
  ======================
    [..] Each DMA channel can be managed through 4 Interrupts:
    (+) Interrupt Source
       (##) DMA_IT_TC: specifies the interrupt source for the Transfer Complete 
            event.
       (##) DMA_IT_HT : specifies the interrupt source for the Half-transfer Complete 
            event.
       (##) DMA_IT_TE : specifies the interrupt source for the transfer errors event.
       (##) DMA_IT_GL : to indicate that at least one of the interrupts described 
            above occurred.
    -@@- Clearing DMA_IT_GL interrupt results in clearing all other interrupts of 
        the same channel (DMA_IT_TCx, DMA_IT_HT and DMA_IT_TE).
    [..]In this Mode it is advised to use the following functions:
        (+) void DMA_ITConfig(DMA_Channel_TypeDef* DMAy_Channelx, uint32_t DMA_IT, 
            FunctionalState NewState);
        (+) ITStatus DMA_GetITStatus(uint32_t DMA_IT);
        (+) void DMA_ClearITPendingBit(uint32_t DMA_IT);

@endverbatim
  * @{
  */

/**
  * @brief  Enables or disables the specified DMAy Channelx interrupts.
  * @param  DMAy_Channelx: where y can be 1 to select the DMA and
  *         x can be 1 to 5 for DMA1 to select the DMA Channel.
  * @param  DMA_IT: specifies the DMA interrupts sources to be enabled
  *         or disabled. 
  *   This parameter can be any combination of the following values:
  *     @arg DMA_IT_TC: Transfer complete interrupt mask
  *     @arg DMA_IT_HT: Half transfer interrupt mask
  *     @arg DMA_IT_TE: Transfer error interrupt mask
  * @param  NewState: new state of the specified DMA interrupts.
  *         This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void DMA_ITConfig(DMA_Channel_TypeDef* DMAy_Channelx, uint32_t DMA_IT, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_DMA_ALL_PERIPH(DMAy_Channelx));
  assert_param(IS_DMA_CONFIG_IT(DMA_IT));
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  if (NewState != DISABLE)
  {
    /* Enable the selected DMA interrupts */
    DMAy_Channelx->CCR |= DMA_IT;
  }
  else
  {
    /* Disable the selected DMA interrupts */
    DMAy_Channelx->CCR &= ~DMA_IT;
  }
}

/**
  * @brief  Checks whether the specified DMAy Channelx flag is set or not.
  * @param  DMA_FLAG: specifies the flag to check.
  *   This parameter can be one of the following values:
  *     @arg DMA1_FLAG_GL1: DMA1 Channel1 global flag.
  *     @arg DMA1_FLAG_TC1: DMA1 Channel1 transfer complete flag.
  *     @arg DMA1_FLAG_HT1: DMA1 Channel1 half transfer flag.
  *     @arg DMA1_FLAG_TE1: DMA1 Channel1 transfer error flag.
  *     @arg DMA1_FLAG_GL2: DMA1 Channel2 global flag.
  *     @arg DMA1_FLAG_TC2: DMA1 Channel2 transfer complete flag.
  *     @arg DMA1_FLAG_HT2: DMA1 Channel2 half transfer flag.
  *     @arg DMA1_FLAG_TE2: DMA1 Channel2 transfer error flag.
  *     @arg DMA1_FLAG_GL3: DMA1 Channel3 global flag.
  *     @arg DMA1_FLAG_TC3: DMA1 Channel3 transfer complete flag.
  *     @arg DMA1_FLAG_HT3: DMA1 Channel3 half transfer flag.
  *     @arg DMA1_FLAG_TE3: DMA1 Channel3 transfer error flag.
  *     @arg DMA1_FLAG_GL4: DMA1 Channel4 global flag.
  *     @arg DMA1_FLAG_TC4: DMA1 Channel4 transfer complete flag.
  *     @arg DMA1_FLAG_HT4: DMA1 Channel4 half transfer flag.
  *     @arg DMA1_FLAG_TE4: DMA1 Channel4 transfer error flag.
  *     @arg DMA1_FLAG_GL5: DMA1 Channel5 global flag.
  *     @arg DMA1_FLAG_TC5: DMA1 Channel5 transfer complete flag.
  *     @arg DMA1_FLAG_HT5: DMA1 Channel5 half transfer flag.
  *     @arg DMA1_FLAG_TE5: DMA1 Channel5 transfer error flag.
  *     
  * @note
  *    The Global flag (DMAy_FLAG_GLx) is set whenever any of the other flags 
  *    relative to the same channel is set (Transfer Complete, Half-transfer 
  *    Complete or Transfer Error flags: DMAy_FLAG_TCx, DMAy_FLAG_HTx or 
  *    DMAy_FLAG_TEx). 
  *      
  * @retval The new state of DMA_FLAG (SET or RESET).
  */
FlagStatus DMA_GetFlagStatus(uint32_t DMA_FLAG)
{
  FlagStatus bitstatus = RESET;

  /* Check the parameters */
  assert_param(IS_DMA_GET_FLAG(DMA_FLAG));

  /* Check the status of the specified DMA flag */
  if ((DMA1->ISR & DMA_FLAG) != (uint32_t)RESET)
  {
    /* DMA_FLAG is set */
    bitstatus = SET;
  }
  else
  {
    /* DMA_FLAG is reset */
    bitstatus = RESET;
  }

  /* Return the DMA_FLAG status */
  return  bitstatus;
}

/**
  * @brief  Clears the DMAy Channelx's pending flags.
  * @param  DMA_FLAG: specifies the flag to clear.
  *   This parameter can be any combination (for the same DMA) of the following values:
  *     @arg DMA1_FLAG_GL1: DMA1 Channel1 global flag.
  *     @arg DMA1_FLAG_TC1: DMA1 Channel1 transfer complete flag.
  *     @arg DMA1_FLAG_HT1: DMA1 Channel1 half transfer flag.
  *     @arg DMA1_FLAG_TE1: DMA1 Channel1 transfer error flag.
  *     @arg DMA1_FLAG_GL2: DMA1 Channel2 global flag.
  *     @arg DMA1_FLAG_TC2: DMA1 Channel2 transfer complete flag.
  *     @arg DMA1_FLAG_HT2: DMA1 Channel2 half transfer flag.
  *     @arg DMA1_FLAG_TE2: DMA1 Channel2 transfer error flag.
  *     @arg DMA1_FLAG_GL3: DMA1 Channel3 global flag.
  *     @arg DMA1_FLAG_TC3: DMA1 Channel3 transfer complete flag.
  *     @arg DMA1_FLAG_HT3: DMA1 Channel3 half transfer flag.
  *     @arg DMA1_FLAG_TE3: DMA1 Channel3 transfer error flag.
  *     @arg DMA1_FLAG_GL4: DMA1 Channel4 global flag.
  *     @arg DMA1_FLAG_TC4: DMA1 Channel4 transfer complete flag.
  *     @arg DMA1_FLAG_HT4: DMA1 Channel4 half transfer flag.
  *     @arg DMA1_FLAG_TE4: DMA1 Channel4 transfer error flag.
  *     @arg DMA1_FLAG_GL5: DMA1 Channel5 global flag.
  *     @arg DMA1_FLAG_TC5: DMA1 Channel5 transfer complete flag.
  *     @arg DMA1_FLAG_HT5: DMA1 Channel5 half transfer flag.
  *     @arg DMA1_FLAG_TE5: DMA1 Channel5 transfer error flag.
  *
  * @note
  *    Clearing the Global flag (DMAy_FLAG_GLx) results in clearing all other flags
  *    relative to the same channel (Transfer Complete, Half-transfer Complete and
  *    Transfer Error flags: DMAy_FLAG_TCx, DMAy_FLAG_HTx and DMAy_FLAG_TEx).
  *
  * @retval None
  */
void DMA_ClearFlag(uint32_t DMA_FLAG)
{
  /* Check the parameters */
  assert_param(IS_DMA_CLEAR_FLAG(DMA_FLAG));

  /* Clear the selected DMA flags */
  DMA1->IFCR = DMA_FLAG;
}

/**
  * @brief  Checks whether the specified DMAy Channelx interrupt has occurred or not.
  * @param  DMA_IT: specifies the DMA interrupt source to check. 
  *   This parameter can be one of the following values:
  *     @arg DMA1_IT_GL1: DMA1 Channel1 global interrupt.
  *     @arg DMA1_IT_TC1: DMA1 Channel1 transfer complete interrupt.
  *     @arg DMA1_IT_HT1: DMA1 Channel1 half transfer interrupt.
  *     @arg DMA1_IT_TE1: DMA1 Channel1 transfer error interrupt.
  *     @arg DMA1_IT_GL2: DMA1 Channel2 global interrupt.
  *     @arg DMA1_IT_TC2: DMA1 Channel2 transfer complete interrupt.
  *     @arg DMA1_IT_HT2: DMA1 Channel2 half transfer interrupt.
  *     @arg DMA1_IT_TE2: DMA1 Channel2 transfer error interrupt.
  *     @arg DMA1_IT_GL3: DMA1 Channel3 global interrupt.
  *     @arg DMA1_IT_TC3: DMA1 Channel3 transfer complete interrupt.
  *     @arg DMA1_IT_HT3: DMA1 Channel3 half transfer interrupt.
  *     @arg DMA1_IT_TE3: DMA1 Channel3 transfer error interrupt.
  *     @arg DMA1_IT_GL4: DMA1 Channel4 global interrupt.
  *     @arg DMA1_IT_TC4: DMA1 Channel4 transfer complete interrupt.
  *     @arg DMA1_IT_HT4: DMA1 Channel4 half transfer interrupt.
  *     @arg DMA1_IT_TE4: DMA1 Channel4 transfer error interrupt.
  *     @arg DMA1_IT_GL5: DMA1 Channel5 global interrupt.
  *     @arg DMA1_IT_TC5: DMA1 Channel5 transfer complete interrupt.
  *     @arg DMA1_IT_HT5: DMA1 Channel5 half transfer interrupt.
  *     @arg DMA1_IT_TE5: DMA1 Channel5 transfer error interrupt.
  *     
  * @note
  *    The Global interrupt (DMAy_FLAG_GLx) is set whenever any of the other 
  *    interrupts relative to the same channel is set (Transfer Complete, 
  *    Half-transfer Complete or Transfer Error interrupts: DMAy_IT_TCx, 
  *    DMAy_IT_HTx or DMAy_IT_TEx). 
  *      
  * @retval The new state of DMA_IT (SET or RESET).
  */
ITStatus DMA_GetITStatus(uint32_t DMA_IT)
{
  ITStatus bitstatus = RESET;

  /* Check the parameters */
  assert_param(IS_DMA_GET_IT(DMA_IT));

  /* Check the status of the specified DMA interrupt */
  if ((DMA1->ISR & DMA_IT) != (uint32_t)RESET)
  {
    /* DMA_IT is set */
    bitstatus = SET;
  }
  else
  {
    /* DMA_IT is reset */
    bitstatus = RESET;
  }
  /* Return the DMA_IT status */
  return  bitstatus;
}

/**
  * @brief  Clears the DMAy Channelx's interrupt pending bits.
  * @param  DMA_IT: specifies the DMA interrupt pending bit to clear.
  *   This parameter can be any combination (for the same DMA) of the following values:
  *     @arg DMA1_IT_GL1: DMA1 Channel1 global interrupt.
  *     @arg DMA1_IT_TC1: DMA1 Channel1 transfer complete interrupt.
  *     @arg DMA1_IT_HT1: DMA1 Channel1 half transfer interrupt.
  *     @arg DMA1_IT_TE1: DMA1 Channel1 transfer error interrupt.
  *     @arg DMA1_IT_GL2: DMA1 Channel2 global interrupt.
  *     @arg DMA1_IT_TC2: DMA1 Channel2 transfer complete interrupt.
  *     @arg DMA1_IT_HT2: DMA1 Channel2 half transfer interrupt.
  *     @arg DMA1_IT_TE2: DMA1 Channel2 transfer error interrupt.
  *     @arg DMA1_IT_GL3: DMA1 Channel3 global interrupt.
  *     @arg DMA1_IT_TC3: DMA1 Channel3 transfer complete interrupt.
  *     @arg DMA1_IT_HT3: DMA1 Channel3 half transfer interrupt.
  *     @arg DMA1_IT_TE3: DMA1 Channel3 transfer error interrupt.
  *     @arg DMA1_IT_GL4: DMA1 Channel4 global interrupt.
  *     @arg DMA1_IT_TC4: DMA1 Channel4 transfer complete interrupt.
  *     @arg DMA1_IT_HT4: DMA1 Channel4 half transfer interrupt.
  *     @arg DMA1_IT_TE4: DMA1 Channel4 transfer error interrupt.
  *     @arg DMA1_IT_GL5: DMA1 Channel5 global interrupt.
  *     @arg DMA1_IT_TC5: DMA1 Channel5 transfer complete interrupt.
  *     @arg DMA1_IT_HT5: DMA1 Channel5 half transfer interrupt.
  *     @arg DMA1_IT_TE5: DMA1 Channel5 transfer error interrupt.
  *     
  * @note
  *    Clearing the Global interrupt (DMAy_IT_GLx) results in clearing all other 
  *    interrupts relative to the same channel (Transfer Complete, Half-transfer 
  *    Complete and Transfer Error interrupts: DMAy_IT_TCx, DMAy_IT_HTx and 
  *    DMAy_IT_TEx).  
  *        
  * @retval None
  */
void DMA_ClearITPendingBit(uint32_t DMA_IT)
{
  /* Check the parameters */
  assert_param(IS_DMA_CLEAR_IT(DMA_IT));

  /* Clear the selected DMA interrupt pending bits */
  DMA1->IFCR = DMA_IT;
}

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/