stm8s_tim1.c

STM8s

  * @retval None
  */
void TIM1_ARRPreloadConfig(FunctionalState NewState)
{
    /* Check the parameters */
    assert_param(IS_FUNCTIONALSTATE_OK(NewState));

    /* Set or Reset the ARPE Bit */
    if (NewState != DISABLE)
    {
        TIM1->CR1 |= TIM1_CR1_ARPE;
    }
    else
    {
        TIM1->CR1 &= (u8)(~TIM1_CR1_ARPE);
    }
}


/**
  * @brief Selects the TIM1 peripheral Commutation event.
  * @param[in] NewState new state of the Commutation event.
  * This parameter can be ENABLE or DISABLE.
  * @retval None
  */
void TIM1_SelectCOM(FunctionalState NewState)
{
    /* Check the parameters */
    assert_param(IS_FUNCTIONALSTATE_OK(NewState));

    /* Set or Reset the COMS Bit */
    if (NewState != DISABLE)
    {
        TIM1->CR2 |= TIM1_CR2_COMS;
    }
    else
    {
        TIM1->CR2 &= (u8)(~TIM1_CR2_COMS);
    }
}

/**
  * @brief Sets or Resets the TIM1 peripheral Capture Compare Preload Control bit.
  * @param[in] NewState new state of the Capture Compare Preload Control bit.
  * This parameter can be ENABLE or DISABLE.
  * @retval None
  */
void TIM1_CCPreloadControl(FunctionalState NewState)
{
    /* Check the parameters */
    assert_param(IS_FUNCTIONALSTATE_OK(NewState));

    /* Set or Reset the CCPC Bit */
    if (NewState != DISABLE)
    {
        TIM1->CR2 |= TIM1_CR2_CCPC;
    }
    else
    {
        TIM1->CR2 &= (u8)(~TIM1_CR2_CCPC);
    }
}


/**
  * @brief Enables or disables the TIM1 peripheral Preload Register on CCR1.
  * @param[in] NewState new state of the Capture Compare Preload register.
  * This parameter can be ENABLE or DISABLE.
  * @retval None
  */
void TIM1_OC1PreloadConfig(FunctionalState NewState)
{
    /* Check the parameters */
    assert_param(IS_FUNCTIONALSTATE_OK(NewState));

    /* Set or Reset the OC1PE Bit */
    if (NewState != DISABLE)
    {
        TIM1->CCMR1 |= TIM1_CCMR_OCxPE;
    }
    else
    {
        TIM1->CCMR1 &= (u8)(~TIM1_CCMR_OCxPE);
    }
}


/**
  * @brief Enables or disables the TIM1 peripheral Preload Register on CCR2.
  * @param[in] NewState new state of the Capture Compare Preload register.
  * This parameter can be ENABLE or DISABLE.
  * @retval None
  */
void TIM1_OC2PreloadConfig(FunctionalState NewState)
{
    /* Check the parameters */
    assert_param(IS_FUNCTIONALSTATE_OK(NewState));

    /* Set or Reset the OC2PE Bit */
    if (NewState != DISABLE)
    {
        TIM1->CCMR2 |= TIM1_CCMR_OCxPE;
    }
    else
    {
        TIM1->CCMR2 &= (u8)(~TIM1_CCMR_OCxPE);
    }
}


/**
  * @brief Enables or disables the TIM1 peripheral Preload Register on CCR3.
  * @param[in] NewState new state of the Capture Compare Preload register.
  * This parameter can be ENABLE or DISABLE.
  * @retval None
  */
void TIM1_OC3PreloadConfig(FunctionalState NewState)
{
    /* Check the parameters */
    assert_param(IS_FUNCTIONALSTATE_OK(NewState));

    /* Set or Reset the OC3PE Bit */
    if (NewState != DISABLE)
    {
        TIM1->CCMR3 |= TIM1_CCMR_OCxPE;
    }
    else
    {
        TIM1->CCMR3 &= (u8)(~TIM1_CCMR_OCxPE);
    }
}


/**
  * @brief Enables or disables the TIM1 peripheral Preload Register on CCR4.
  * @param[in] NewState new state of the Capture Compare Preload register.
  * This parameter can be ENABLE or DISABLE.
  * @retval None
  */

void TIM1_OC4PreloadConfig(FunctionalState NewState)
{
    /* Check the parameters */
    assert_param(IS_FUNCTIONALSTATE_OK(NewState));

    /* Set or Reset the OC4PE Bit */
    if (NewState != DISABLE)
    {
        TIM1->CCMR4 |= TIM1_CCMR_OCxPE;
    }
    else
    {
        TIM1->CCMR4 &= (u8)(~TIM1_CCMR_OCxPE);
    }
}

/**
  * @brief Configures the TIM1 Capture Compare 1 Fast feature.
  * @param[in] NewState new state of the Output Compare Fast Enable bit.
  * This parameter can be ENABLE or DISABLE.
  * @retval None
  */
void TIM1_OC1FastConfig(FunctionalState NewState)
{
    /* Check the parameters */
    assert_param(IS_FUNCTIONALSTATE_OK(NewState));

    /* Set or Reset the OC1FE Bit */
    if (NewState != DISABLE)
    {
        TIM1->CCMR1 |= TIM1_CCMR_OCxFE;
    }
    else
    {
        TIM1->CCMR1 &= (u8)(~TIM1_CCMR_OCxFE);
    }
}


/**
  * @brief Configures the TIM1 Capture Compare 2 Fast feature.
  * @param[in] NewState new state of the Output Compare Fast Enable bit.
  * This parameter can be ENABLE or DISABLE.
  * @retval None
  */

void TIM1_OC2FastConfig(FunctionalState NewState)
{
    /* Check the parameters */
    assert_param(IS_FUNCTIONALSTATE_OK(NewState));

    /* Set or Reset the OC2FE Bit */
    if (NewState != DISABLE)
    {
        TIM1->CCMR2 |= TIM1_CCMR_OCxFE;
    }
    else
    {
        TIM1->CCMR2 &= (u8)(~TIM1_CCMR_OCxFE);
    }
}


/**
  * @brief Configures the TIM1 Capture Compare 3 Fast feature.
  * @param[in] NewState new state of the Output Compare Fast Enable bit.
  * This parameter can be ENABLE or DISABLE.
  * @retval None
  */
void TIM1_OC3FastConfig(FunctionalState NewState)
{
    /* Check the parameters */
    assert_param(IS_FUNCTIONALSTATE_OK(NewState));

    /* Set or Reset the OC3FE Bit */
    if (NewState != DISABLE)
    {
        TIM1->CCMR3 |= TIM1_CCMR_OCxFE;
    }
    else
    {
        TIM1->CCMR3 &= (u8)(~TIM1_CCMR_OCxFE);
    }
}


/**
  * @brief Configures the TIM1 Capture Compare 4 Fast feature.
  * @param[in] NewState new state of the Output Compare Fast Enable bit.
  * This parameter can be ENABLE or DISABLE.
  * @retval None
  */
void TIM1_OC4FastConfig(FunctionalState NewState)
{
    /* Check the parameters */
    assert_param(IS_FUNCTIONALSTATE_OK(NewState));

    /* Set or Reset the OC4FE Bit */
    if (NewState != DISABLE)
    {
        TIM1->CCMR4 |= TIM1_CCMR_OCxFE;
    }
    else
    {
        TIM1->CCMR4 &= (u8)(~TIM1_CCMR_OCxFE);
    }
}


/**
  * @brief Configures the TIM1 event to be generated by software.
  * @param[in] TIM1_EventSource specifies the event source.
  * This parameter can be one of the following values:
  *                       - TIM1_EVENTSOURCE_UPDATE: TIM1 update Event source
  *                       - TIM1_EVENTSOURCE_CC1: TIM1 Capture Compare 1 Event source
  *                       - TIM1_EVENTSOURCE_CC2: TIM1 Capture Compare 2 Event source
  *                       - TIM1_EVENTSOURCE_CC3: TIM1 Capture Compare 3 Event source
  *                       - TIM1_EVENTSOURCE_CC4: TIM1 Capture Compare 4 Event source
  *                       - TIM1_EVENTSOURCE_COM: TIM1 COM Event source
  *                       - TIM1_EVENTSOURCE_TRIGGER: TIM1 Trigger Event source
  *                       - TIM1_EventSourceBreak: TIM1 Break Event source
  * @retval None
  */
void TIM1_GenerateEvent(TIM1_EventSource_TypeDef TIM1_EventSource)
{
    /* Check the parameters */
    assert_param(IS_TIM1_EVENT_SOURCE_OK(TIM1_EventSource));

    /* Set the event sources */
    TIM1->EGR = (u8)TIM1_EventSource;
}


/**
  * @brief Configures the TIM1 Channel 1 polarity.
  * @param[in] TIM1_OCPolarity specifies the OC1 Polarity.
  * This parameter can be one of the following values:
  *                       - TIM1_OCPOLARITY_LOW: Output Compare active low
  *                       - TIM1_OCPOLARITY_HIGH: Output Compare active high
  * @retval None
  */
void TIM1_OC1PolarityConfig(TIM1_OCPolarity_TypeDef TIM1_OCPolarity)
{
    /* Check the parameters */
    assert_param(IS_TIM1_OC_POLARITY_OK(TIM1_OCPolarity));

    /* Set or Reset the CC1P Bit */
    if (TIM1_OCPolarity != TIM1_OCPOLARITY_HIGH)
    {
        TIM1->CCER1 |= TIM1_CCER1_CC1P;
    }
    else
    {
        TIM1->CCER1 &= (u8)(~TIM1_CCER1_CC1P);
    }
}


/**
  * @brief Configures the TIM1 Channel 1N polarity.
  * @param[in] TIM1_OCNPolarity specifies the OC1N Polarity.
  * This parameter can be one of the following values:
  *                       - TIM1_OCNPOLARITY_LOW: Output Compare active low
  *                       - TIM1_OCNPOLARITY_HIGH: Output Compare active high
  * @retval None
  */
void TIM1_OC1NPolarityConfig(TIM1_OCNPolarity_TypeDef TIM1_OCNPolarity)
{
    /* Check the parameters */
    assert_param(IS_TIM1_OCN_POLARITY_OK(TIM1_OCNPolarity));

    /* Set or Reset the CC3P Bit */
    if (TIM1_OCNPolarity != TIM1_OCNPOLARITY_HIGH)
    {
        TIM1->CCER1 |= TIM1_CCER1_CC1NP;
    }
    else
    {
        TIM1->CCER1 &= (u8)(~TIM1_CCER1_CC1NP);
    }
}


/**
  * @brief Configures the TIM1 Channel 2 polarity.
  * @param[in] TIM1_OCPolarity specifies the OC2 Polarity.
  * This parameter can be one of the following values:
  *                       - TIM1_OCPOLARITY_LOW: Output Compare active low
  *                       - TIM1_OCPOLARITY_HIGH: Output Compare active high
  * @retval None
  */
void TIM1_OC2PolarityConfig(TIM1_OCPolarity_TypeDef TIM1_OCPolarity)
{
    /* Check the parameters */
    assert_param(IS_TIM1_OC_POLARITY_OK(TIM1_OCPolarity));

    /* Set or Reset the CC2P Bit */
    if (TIM1_OCPolarity != TIM1_OCPOLARITY_HIGH)
    {
        TIM1->CCER1 |= TIM1_CCER1_CC2P;
    }
    else
    {
        TIM1->CCER1 &= (u8)(~TIM1_CCER1_CC2P);
    }
}

/**
  * @brief Configures the TIM1 Channel 2N polarity.
  * @param[in] TIM1_OCNPolarity specifies the OC2N Polarity.
  * This parameter can be one of the following values:
  *                       - TIM1_OCNPOLARITY_LOW: Output Compare active low
  *                       - TIM1_OCNPOLARITY_HIGH: Output Compare active high
  * @retval None
  */
void TIM1_OC2NPolarityConfig(TIM1_OCNPolarity_TypeDef TIM1_OCNPolarity)
{
    /* Check the parameters */
    assert_param(IS_TIM1_OCN_POLARITY_OK(TIM1_OCNPolarity));

    /* Set or Reset the CC3P Bit */
    if (TIM1_OCNPolarity != TIM1_OCNPOLARITY_HIGH)
    {
        TIM1->CCER1 |= TIM1_CCER1_CC2NP;
    }
    else
    {
        TIM1->CCER1 &= (u8)(~TIM1_CCER1_CC2NP);
    }