ili932x.c

UCOSII在STM32平台的移植

	      LCD_WR_CmdPar(0x00E7,0x0012);
	      LCD_WR_CmdPar(0x00Ef,0x1231); 	// Set the internal timing;
        
    	  //LCD_WR_CmdPar(0x0000,0x0001);         // Start internal OSC.
	      Delayms(20);                                      // Delay 20ms
        
	      LCD_WR_CmdPar(0x0001,0x0100);         // set SS and SM bit
    	  LCD_WR_CmdPar(0x0002,0x0700);         // set line inversion
    	  LCD_WR_CmdPar(0x0003,0x1030);         // TRI=1;DFM=0; set GRAM write direction and BGR=1 
	      LCD_WR_CmdPar(0x0004,0x0000);         // Resize register
        
	      LCD_WR_CmdPar(0x0008,0x0202);         // set the back porch and front porch
    	  LCD_WR_CmdPar(0x0009,0x0000);         // set non-display area refresh cycle ISC[3:0]
    	  LCD_WR_CmdPar(0x000A,0x0008);         // FMARK function
    
        //***************************Power on sequence******************************//

        LCD_WR_CmdPar(0x0010,0x0000);         // SAP, BT[3:0], AP, DSTB, SLP, STB
        LCD_WR_CmdPar(0x0011,0x0007);         // DC1[2:0], DC0[2:0], VC[2:0]
        LCD_WR_CmdPar(0x0012,0x0000);      	// VREG1OUT voltage
        LCD_WR_CmdPar(0x0013,0x0000);      	// VDV[4:0] for VCOM amplitude
        Delayms(200);                                  	// Dis-charge capacitor power voltage

 	      LCD_WR_CmdPar(0x0010,0x1190);      	// SAP, BT[3:0], AP, DSTB, SLP, STB
        LCD_WR_CmdPar(0x0011,0x0227);      	// DC1[2:0], DC0[2:0], VC[2:0]
        Delayms(50);                                      // Delay 50ms

        //LCD_WR_CmdPar(0x0012,0x001c);      	// VREG1OUT voltage
        LCD_WR_CmdPar(0x0012,0x015c);      	// VREG1OUT voltage
        Delayms(50);                                      // Delay 50ms

        LCD_WR_CmdPar(0x0013,0x1200);         // VDV[4:0] for VCOM amplitude
        LCD_WR_CmdPar(0x0029,0x001D);         // VCM[4:0] for VCOMH
        LCD_WR_CmdPar(0x002B,0x0009);         // Frame=60Hz;
        Delayms(50);                                      // Delay 50ms

        //*************************Adjust the Gamma Curve****************************//  

        LCD_WR_CmdPar(0x0030,0x0100);
        LCD_WR_CmdPar(0x0031,0x0408);
        LCD_WR_CmdPar(0x0032,0x0000);
        LCD_WR_CmdPar(0x0035,0x0103);
        LCD_WR_CmdPar(0x0036,0x1604);
        LCD_WR_CmdPar(0x0037,0x0305);
        LCD_WR_CmdPar(0x0038,0x0004);
        LCD_WR_CmdPar(0x0039,0x0807);
        LCD_WR_CmdPar(0x003C,0x0401);
        LCD_WR_CmdPar(0x003D,0x000A);   

	      //*****************************Set GRAM Area*********************************//
	      LCD_WR_CmdPar(0x0050,0x0000);		// Horizontal GRAM Start Address
      	LCD_WR_CmdPar(0x0051,0x00EF);		// Horizontal GRAM End Address
      	LCD_WR_CmdPar(0x0052,0x0000);		// Vertical GRAM Start Address
      	LCD_WR_CmdPar(0x0053,0x013F);		// Vertical GRAM Start Address
    
      	LCD_WR_CmdPar(0x0060,0xa700);		// Gate Scan Line
      	LCD_WR_CmdPar(0x0061,0x0001);		// NDL,VLE, REV
      	LCD_WR_CmdPar(0x006A,0x0000);		// set scrolling line
    
	      //************************Partial Display Control****************************//
	      LCD_WR_CmdPar(0x0080,0x0000);
      	LCD_WR_CmdPar(0x0081,0x0000);
      	LCD_WR_CmdPar(0x0082,0x0000);
      	LCD_WR_CmdPar(0x0083,0x0000);
      	LCD_WR_CmdPar(0x0084,0x0000);
      	LCD_WR_CmdPar(0x0085,0x0000);
    
	      //****************************Panel Control**********************************//
	      LCD_WR_CmdPar(0x0090,0x0010);		//set frame
      	LCD_WR_CmdPar(0x0092,0x0000);
      	LCD_WR_CmdPar(0x0093,0x0003);
      	LCD_WR_CmdPar(0x0095,0x0110);
      	LCD_WR_CmdPar(0x0097,0x0000);
      	LCD_WR_CmdPar(0x0098,0x0000);
    
      	LCD_WR_CmdPar(0x0007,0x0133);		// 262K color and display ON
	      Delayms(10);
   }
   else if (i == 0x9320)
   {
      LCD_WR_CmdPar(0x00, 0x0000);
      LCD_WR_CmdPar(0x01, 0x0100);  //Driver Output Contral.
      LCD_WR_CmdPar(0x02, 0x0700);  //LCD Driver Waveform Contral.
      LCD_WR_CmdPar(0x03, 0x1030);  //Entry Mode Set.

      LCD_WR_CmdPar(0x04, 0x0000);  //Scalling Contral.
      LCD_WR_CmdPar(0x08, 0x0202);  //Display Contral 2.(0x0207)
      LCD_WR_CmdPar(0x09, 0x0000);  //Display Contral 3.(0x0000)
      LCD_WR_CmdPar(0x0a, 0x0000);  //Frame Cycle Contal.(0x0000)
      LCD_WR_CmdPar(0x0c, (1 << 0));   //Extern Display Interface Contral 1.(0x0000)
      LCD_WR_CmdPar(0x0d, 0x0000);  //Frame Maker Position.
      LCD_WR_CmdPar(0x0f, 0x0000);  //Extern Display Interface Contral 2.

      for (i = 50000; i > 0; i--);
      LCD_WR_CmdPar(0x07, 0x0101);  //Display Contral.
      for (i = 50000; i > 0; i--);

      LCD_WR_CmdPar(0x10, (1 << 12) | (0 << 8) | (1 << 7) | (1 << 6) | (0 << 4));   //Power Control 1.(0x16b0)
      LCD_WR_CmdPar(0x11, 0x0007);                       //Power Control 2.(0x0001)
      LCD_WR_CmdPar(0x12, (1 << 8) | (1 << 4) | (0 << 0));              //Power Control 3.(0x0138)
      LCD_WR_CmdPar(0x13, 0x0b00);                       //Power Control 4.
      LCD_WR_CmdPar(0x29, 0x0000);                       //Power Control 7.

      LCD_WR_CmdPar(0x2b, (1 << 14) | (1 << 4));

      LCD_WR_CmdPar(0x50, 0);    //Set X Start.
      LCD_WR_CmdPar(0x51, 239);  //Set X End.
      LCD_WR_CmdPar(0x52, 0);    //Set Y Start.
      LCD_WR_CmdPar(0x53, 319);  //Set Y End.

      LCD_WR_CmdPar(0x60, 0x2700);  //Driver Output Control.
      LCD_WR_CmdPar(0x61, 0x0001);  //Driver Output Control.
      LCD_WR_CmdPar(0x6a, 0x0000);  //Vertical Srcoll Control.

      LCD_WR_CmdPar(0x80, 0x0000);  //Display Position? Partial Display 1.
      LCD_WR_CmdPar(0x81, 0x0000);  //RAM Address Start? Partial Display 1.
      LCD_WR_CmdPar(0x82, 0x0000);  //RAM Address End-Partial Display 1.
      LCD_WR_CmdPar(0x83, 0x0000);  //Displsy Position? Partial Display 2.
      LCD_WR_CmdPar(0x84, 0x0000);  //RAM Address Start? Partial Display 2.
      LCD_WR_CmdPar(0x85, 0x0000);  //RAM Address End? Partial Display 2.

      LCD_WR_CmdPar(0x90, (0 << 7) | (16 << 0));   //Frame Cycle Contral.(0x0013)
      LCD_WR_CmdPar(0x92, 0x0000);  //Panel Interface Contral 2.(0x0000)
      LCD_WR_CmdPar(0x93, 0x0001);  //Panel Interface Contral 3.
      LCD_WR_CmdPar(0x95, 0x0110);  //Frame Cycle Contral.(0x0110)
      LCD_WR_CmdPar(0x97, (0 << 8));   //
      LCD_WR_CmdPar(0x98, 0x0000);  //Frame Cycle Contral.


      LCD_WR_CmdPar(0x07, 0x0173);  //(0x0173)
   }
   else	if(i==0x7781)
   {
   	  //--------------------------------ST7781 Internal Register Initial---------------------------------------//
	    LCD_WR_CmdPar(0x00ff, 0x0001); //wr_cmd(0x00ff);wr_data(0x0001);
	    LCD_WR_CmdPar(0x00f3, 0x0008); //wr_cmd(0x00f3);wr_data(0x0008);
	    //LCD_CtrlRead_ST7781 (0x00f3); //Read Parameter
	    //---------------------------End ST7781 Internal Register Initial--------------------------------------//
	    //------------------------------------Display Control Setting----------------------------------------------//
	    LCD_WR_CmdPar(0x0001, 0x0100); //wr_cmd(0x0001);wr_data(0x0100); //Output Direct
	    LCD_WR_CmdPar(0x0002, 0x0700); //wr_cmd(0x0002);wr_data(0x0700); //Line Inversion
	    LCD_WR_CmdPar(0x0003, 0x1030); //wr_cmd(0x0003);wr_data(0x1030); //Entry Mode (65K, BGR)
	    LCD_WR_CmdPar(0x0008, 0x0807); //wr_cmd(0x0008);wr_data(0x0807); // Porch Setting
	    LCD_WR_CmdPar(0x000a, 0x0000); //wr_cmd(0x000A);wr_data(0x0000); //FMARK off
	    //-----------------------------------End Display Control setting-----------------------------------------//
	    //-------------------------------- Power Control Registers Initial --------------------------------------//
	    LCD_WR_CmdPar(0x0010, 0x0790); //wr_cmd(0x0010);wr_data(0x0790); //Power Control1
	    LCD_WR_CmdPar(0x0011, 0x0005); //wr_cmd(0x0011);wr_data(0x0005); //Power Control2
	    LCD_WR_CmdPar(0x0012, 0x0000); //wr_cmd(0x0012);wr_data(0x0000); //Power Control3
	    LCD_WR_CmdPar(0x0013, 0x0000); //wr_cmd(0x0013);wr_data(0x0000); //Power Control4
	    //---------------------------------End Power Control Registers Initial -------------------------------//
	    Delay_nms(1); //Delayms(1); //for (i = 50000; i > 0; i--); //SysTickDelay(100); //Delay 100ms
	    //--------------------------------- Power Supply Startup 1 Setting------------------------------------//
	    LCD_WR_CmdPar(0x0010, 0x1490); //wr_cmd(0x0010);wr_data(0x1490); //Power Control1
	    Delay_nms(1); //Delayms(1); //for (i = 50000; i > 0; i--); //SysTickDelay(50); //Delay 50ms
	    LCD_WR_CmdPar(0x0011, 0x0227); //wr_cmd(0x0011);wr_data(0x0227); //Power Control2
	    //--------------------------------- End Power Supply Startup 1 Setting------------------------------//
	    Delay_nms(1); //Delayms(1); //for (i = 50000; i > 0; i--); //SysTickDelay(50); //Delay 50ms
	    //--------------------------------- Power Supply Startup 2 Setting------------------------------------//
	    LCD_WR_CmdPar(0x0012, 0x0089); //wr_cmd(0x0012);wr_data(0x0089); //Power Control3
	    LCD_WR_CmdPar(0x0013, 0x1900); //wr_cmd(0x0013);wr_data(0x1900); //Power Control4
	    LCD_WR_CmdPar(0x0029, 0x0021); //wr_cmd(0x0029);wr_data(0x0021); //VCOMH setting
	    //--------------------------------- End Power Supply Startup 2 Setting------------------------------//
	    Delay_nms(1); //Delayms(1); //for (i = 50000; i > 0; i--); //SysTickDelay(50); //Delay 50ms
	    //-------------------------------------Gamma Cluster Setting-------------------------------------------//
	    LCD_WR_CmdPar(0x0030, 0x0000); //wr_cmd(0x0030);wr_data(0x0000);
	    LCD_WR_CmdPar(0x0031, 0x0006); //wr_cmd(0x0031);wr_data(0x0006);
	    LCD_WR_CmdPar(0x0032, 0x0100); //wr_cmd(0x0032);wr_data(0x0100);
	    LCD_WR_CmdPar(0x0035, 0x0001); //wr_cmd(0x0035);wr_data(0x0001);
	    LCD_WR_CmdPar(0x0036, 0x0000); //wr_cmd(0x0036);wr_data(0x0000);
	    LCD_WR_CmdPar(0x0037, 0x0000); //wr_cmd(0x0037);wr_data(0x0000);
	    LCD_WR_CmdPar(0x0038, 0x0406); //wr_cmd(0x0038);wr_data(0x0406);
	    LCD_WR_CmdPar(0x0039, 0x0202); //wr_cmd(0x0039);wr_data(0x0202);
	    LCD_WR_CmdPar(0x003c, 0x0001); //wr_cmd(0x003c);wr_data(0x0001);
	    LCD_WR_CmdPar(0x003d, 0x0000); //wr_cmd(0x003d);wr_data(0x0000);
	    //---------------------------------------End Gamma Setting---------------------------------------------//
	    //----------------------------------Display Windows 240 X 320----------------------------------------//
	    LCD_WR_CmdPar(0x0050, 0x0000); //wr_cmd(0x0050);wr_data(0x0000); // Horizontal Address Start Position
	    LCD_WR_CmdPar(0x0051, 0x00ef); //wr_cmd(0x0051);wr_data(0x00ef); // Horizontal Address End Position
	    LCD_WR_CmdPar(0x0052, 0x0000); //wr_cmd(0x0052);wr_data(0x0000); // Vertical Address Start Position
	    LCD_WR_CmdPar(0x0053, 0x013f); //wr_cmd(0x0053);wr_data(0x013f); // Vertical Address End Position
	    //----------------------------------End Display Windows 240 X 320----------------------------------//
	    //-------------------------------------------Frame Rate Setting-------------------------------------------//
	    LCD_WR_CmdPar(0x0060, 0xa700); //wr_cmd(0x0060);wr_data(0xa700); //Gate scan control
	    LCD_WR_CmdPar(0x0061, 0x0001); //wr_cmd(0x0061);wr_data(0x0001); //Non-display Area setting
	    LCD_WR_CmdPar(0x0090, 0x0033); //wr_cmd(0x0090);wr_data(0x0033); //RTNI setting
	    //-------------------------------------------END Frame Rate setting------------------------------------//
	    LCD_WR_CmdPar(0x0007, 0x0133); //wr_cmd(0x0007);wr_data(0x0133); //Display Control1
	    Delay_nms(1); //Delayms(1); //for (i = 50000; i > 0; i--); //SysTickDelay(50); //Delay 50ms
	    
	    LCD_WR_Cmd(0x0022); //wr_cmd(0x0022);	
   }

}


void Delay_nms(int n)
{
   u32 f = n, k;
   for (; f != 0; f--)
   {
      for (k = 0xFFF; k != 0; k--)
         ;
   }
}