m68k.c

linux下编程用 编译软件

const char *
output_move_simode (rtx *operands)
{
  if (GET_CODE (operands[1]) == CONST_INT)
    return output_move_simode_const (operands);
  else if ((GET_CODE (operands[1]) == SYMBOL_REF
	    || GET_CODE (operands[1]) == CONST)
	   && push_operand (operands[0], SImode))
    return "pea %a1";
  else if ((GET_CODE (operands[1]) == SYMBOL_REF
	    || GET_CODE (operands[1]) == CONST)
	   && ADDRESS_REG_P (operands[0]))
    return "lea %a1,%0";
  return "move%.l %1,%0";
}

const char *
output_move_himode (rtx *operands)
{
 if (GET_CODE (operands[1]) == CONST_INT)
    {
      if (operands[1] == const0_rtx
	  && (DATA_REG_P (operands[0])
	      || GET_CODE (operands[0]) == MEM)
	  /* clr insns on 68000 read before writing.
	     This isn't so on the 68010, but we have no TARGET_68010.  */
	  && ((TARGET_68020 || TARGET_COLDFIRE)
	      || !(GET_CODE (operands[0]) == MEM
		   && MEM_VOLATILE_P (operands[0]))))
	return "clr%.w %0";
      else if (operands[1] == const0_rtx
	       && ADDRESS_REG_P (operands[0]))
	return "sub%.l %0,%0";
      else if (DATA_REG_P (operands[0])
	       && INTVAL (operands[1]) < 128
	       && INTVAL (operands[1]) >= -128)
	{
	  return "moveq %1,%0";
	}
      else if (INTVAL (operands[1]) < 0x8000
	       && INTVAL (operands[1]) >= -0x8000)
	return "move%.w %1,%0";
    }
  else if (CONSTANT_P (operands[1]))
    return "move%.l %1,%0";
  /* Recognize the insn before a tablejump, one that refers
     to a table of offsets.  Such an insn will need to refer
     to a label on the insn.  So output one.  Use the label-number
     of the table of offsets to generate this label.  This code,
     and similar code below, assumes that there will be at most one
     reference to each table.  */
  if (GET_CODE (operands[1]) == MEM
      && GET_CODE (XEXP (operands[1], 0)) == PLUS
      && GET_CODE (XEXP (XEXP (operands[1], 0), 1)) == LABEL_REF
      && GET_CODE (XEXP (XEXP (operands[1], 0), 0)) != PLUS)
    {
      rtx labelref = XEXP (XEXP (operands[1], 0), 1);
      if (MOTOROLA)
	asm_fprintf (asm_out_file, "\t.set %LLI%d,.+2\n",
		     CODE_LABEL_NUMBER (XEXP (labelref, 0)));
      else
	(*targetm.asm_out.internal_label) (asm_out_file, "LI",
		     CODE_LABEL_NUMBER (XEXP (labelref, 0)));
    }
  return "move%.w %1,%0";
}

const char *
output_move_qimode (rtx *operands)
{
  /* 68k family always modifies the stack pointer by at least 2, even for
     byte pushes.  The 5200 (ColdFire) does not do this.  */
  
  /* This case is generated by pushqi1 pattern now */
  gcc_assert (!(GET_CODE (operands[0]) == MEM
		&& GET_CODE (XEXP (operands[0], 0)) == PRE_DEC
		&& XEXP (XEXP (operands[0], 0), 0) == stack_pointer_rtx
		&& ! ADDRESS_REG_P (operands[1])
		&& ! TARGET_COLDFIRE));

  /* clr and st insns on 68000 read before writing.
     This isn't so on the 68010, but we have no TARGET_68010.  */
  if (!ADDRESS_REG_P (operands[0])
      && ((TARGET_68020 || TARGET_COLDFIRE)
	  || !(GET_CODE (operands[0]) == MEM && MEM_VOLATILE_P (operands[0]))))
    {
      if (operands[1] == const0_rtx)
	return "clr%.b %0";
      if ((!TARGET_COLDFIRE || DATA_REG_P (operands[0]))
	  && GET_CODE (operands[1]) == CONST_INT
	  && (INTVAL (operands[1]) & 255) == 255)
	{
	  CC_STATUS_INIT;
	  return "st %0";
	}
    }
  if (GET_CODE (operands[1]) == CONST_INT
      && DATA_REG_P (operands[0])
      && INTVAL (operands[1]) < 128
      && INTVAL (operands[1]) >= -128)
    {
      return "moveq %1,%0";
    }
  if (operands[1] == const0_rtx && ADDRESS_REG_P (operands[0]))
    return "sub%.l %0,%0";
  if (GET_CODE (operands[1]) != CONST_INT && CONSTANT_P (operands[1]))
    return "move%.l %1,%0";
  /* 68k family (including the 5200 ColdFire) does not support byte moves to
     from address registers.  */
  if (ADDRESS_REG_P (operands[0]) || ADDRESS_REG_P (operands[1]))
    return "move%.w %1,%0";
  return "move%.b %1,%0";
}

const char *
output_move_stricthi (rtx *operands)
{
  if (operands[1] == const0_rtx
      /* clr insns on 68000 read before writing.
	 This isn't so on the 68010, but we have no TARGET_68010.  */
      && ((TARGET_68020 || TARGET_COLDFIRE)
	  || !(GET_CODE (operands[0]) == MEM && MEM_VOLATILE_P (operands[0]))))
    return "clr%.w %0";
  return "move%.w %1,%0";
}

const char *
output_move_strictqi (rtx *operands)
{
  if (operands[1] == const0_rtx
      /* clr insns on 68000 read before writing.
         This isn't so on the 68010, but we have no TARGET_68010.  */
      && ((TARGET_68020 || TARGET_COLDFIRE)
          || !(GET_CODE (operands[0]) == MEM && MEM_VOLATILE_P (operands[0]))))
    return "clr%.b %0";
  return "move%.b %1,%0";
}

/* Return the best assembler insn template
   for moving operands[1] into operands[0] as a fullword.  */

static const char *
singlemove_string (rtx *operands)
{
  if (GET_CODE (operands[1]) == CONST_INT)
    return output_move_simode_const (operands);
  return "move%.l %1,%0";
}


/* Output assembler code to perform a doubleword move insn
   with operands OPERANDS.  */

const char *
output_move_double (rtx *operands)
{
  enum
    {
      REGOP, OFFSOP, MEMOP, PUSHOP, POPOP, CNSTOP, RNDOP
    } optype0, optype1;
  rtx latehalf[2];
  rtx middlehalf[2];
  rtx xops[2];
  rtx addreg0 = 0, addreg1 = 0;
  int dest_overlapped_low = 0;
  int size = GET_MODE_SIZE (GET_MODE (operands[0]));

  middlehalf[0] = 0;
  middlehalf[1] = 0;

  /* First classify both operands.  */

  if (REG_P (operands[0]))
    optype0 = REGOP;
  else if (offsettable_memref_p (operands[0]))
    optype0 = OFFSOP;
  else if (GET_CODE (XEXP (operands[0], 0)) == POST_INC)
    optype0 = POPOP;
  else if (GET_CODE (XEXP (operands[0], 0)) == PRE_DEC)
    optype0 = PUSHOP;
  else if (GET_CODE (operands[0]) == MEM)
    optype0 = MEMOP;
  else
    optype0 = RNDOP;

  if (REG_P (operands[1]))
    optype1 = REGOP;
  else if (CONSTANT_P (operands[1]))
    optype1 = CNSTOP;
  else if (offsettable_memref_p (operands[1]))
    optype1 = OFFSOP;
  else if (GET_CODE (XEXP (operands[1], 0)) == POST_INC)
    optype1 = POPOP;
  else if (GET_CODE (XEXP (operands[1], 0)) == PRE_DEC)
    optype1 = PUSHOP;
  else if (GET_CODE (operands[1]) == MEM)
    optype1 = MEMOP;
  else
    optype1 = RNDOP;

  /* Check for the cases that the operand constraints are not supposed
     to allow to happen.  Generating code for these cases is
     painful.  */
  gcc_assert (optype0 != RNDOP && optype1 != RNDOP);

  /* If one operand is decrementing and one is incrementing
     decrement the former register explicitly
     and change that operand into ordinary indexing.  */

  if (optype0 == PUSHOP && optype1 == POPOP)
    {
      operands[0] = XEXP (XEXP (operands[0], 0), 0);
      if (size == 12)
        output_asm_insn ("sub%.l #12,%0", operands);
      else
        output_asm_insn ("subq%.l #8,%0", operands);
      if (GET_MODE (operands[1]) == XFmode)
	operands[0] = gen_rtx_MEM (XFmode, operands[0]);
      else if (GET_MODE (operands[0]) == DFmode)
	operands[0] = gen_rtx_MEM (DFmode, operands[0]);
      else
	operands[0] = gen_rtx_MEM (DImode, operands[0]);
      optype0 = OFFSOP;
    }
  if (optype0 == POPOP && optype1 == PUSHOP)
    {
      operands[1] = XEXP (XEXP (operands[1], 0), 0);
      if (size == 12)
        output_asm_insn ("sub%.l #12,%1", operands);
      else
        output_asm_insn ("subq%.l #8,%1", operands);
      if (GET_MODE (operands[1]) == XFmode)
	operands[1] = gen_rtx_MEM (XFmode, operands[1]);
      else if (GET_MODE (operands[1]) == DFmode)
	operands[1] = gen_rtx_MEM (DFmode, operands[1]);
      else
	operands[1] = gen_rtx_MEM (DImode, operands[1]);
      optype1 = OFFSOP;
    }

  /* If an operand is an unoffsettable memory ref, find a register
     we can increment temporarily to make it refer to the second word.  */

  if (optype0 == MEMOP)
    addreg0 = find_addr_reg (XEXP (operands[0], 0));

  if (optype1 == MEMOP)
    addreg1 = find_addr_reg (XEXP (operands[1], 0));

  /* Ok, we can do one word at a time.
     Normally we do the low-numbered word first,
     but if either operand is autodecrementing then we
     do the high-numbered word first.

     In either case, set up in LATEHALF the operands to use
     for the high-numbered word and in some cases alter the
     operands in OPERANDS to be suitable for the low-numbered word.  */

  if (size == 12)
    {
      if (optype0 == REGOP)
	{
	  latehalf[0] = gen_rtx_REG (SImode, REGNO (operands[0]) + 2);
	  middlehalf[0] = gen_rtx_REG (SImode, REGNO (operands[0]) + 1);
	}
      else if (optype0 == OFFSOP)
	{
	  middlehalf[0] = adjust_address (operands[0], SImode, 4);
	  latehalf[0] = adjust_address (operands[0], SImode, size - 4);
	}
      else
	{
	  middlehalf[0] = operands[0];
	  latehalf[0] = operands[0];
	}

      if (optype1 == REGOP)
	{
	  latehalf[1] = gen_rtx_REG (SImode, REGNO (operands[1]) + 2);
	  middlehalf[1] = gen_rtx_REG (SImode, REGNO (operands[1]) + 1);
	}
      else if (optype1 == OFFSOP)
	{
	  middlehalf[1] = adjust_address (operands[1], SImode, 4);
	  latehalf[1] = adjust_address (operands[1], SImode, size - 4);
	}
      else if (optype1 == CNSTOP)
	{
	  if (GET_CODE (operands[1]) == CONST_DOUBLE)
	    {
	      REAL_VALUE_TYPE r;
	      long l[3];

	      REAL_VALUE_FROM_CONST_DOUBLE (r, operands[1]);
	      REAL_VALUE_TO_TARGET_LONG_DOUBLE (r, l);
	      operands[1] = GEN_INT (l[0]);
	      middlehalf[1] = GEN_INT (l[1]);
	      latehalf[1] = GEN_INT (l[2]);
	    }
	  else
	    {
	      /* No non-CONST_DOUBLE constant should ever appear
		 here.  */
	      gcc_assert (!CONSTANT_P (operands[1]));
	    }
	}
      else
	{
	  middlehalf[1] = operands[1];
	  latehalf[1] = operands[1];
	}
    }
  else
    /* size is not 12: */
    {
      if (optype0 == REGOP)
	latehalf[0] = gen_rtx_REG (SImode, REGNO (operands[0]) + 1);
      else if (optype0 == OFFSOP)
	latehalf[0] = adjust_address (operands[0], SImode, size - 4);
      else
	latehalf[0] = operands[0];

      if (optype1 == REGOP)
	latehalf[1] = gen_rtx_REG (SImode, REGNO (operands[1]) + 1);
      else if (optype1 == OFFSOP)
	latehalf[1] = adjust_address (operands[1], SImode, size - 4);
      else if (optype1 == CNSTOP)
	split_double (operands[1], &operands[1], &latehalf[1]);
      else
	latehalf[1] = operands[1];
    }

  /* If insn is effectively movd N(sp),-(sp) then we will do the
     high word first.  We should use the adjusted operand 1 (which is N+4(sp))
     for the low word as well, to compensate for the first decrement of sp.  */
  if (optype0 == PUSHOP
      && REGNO (XEXP (XEXP (operands[0], 0), 0)) == STACK_POINTER_REGNUM
      && reg_overlap_mentioned_p (stack_pointer_rtx, operands[1]))
    operands[1] = middlehalf[1] = latehalf[1];

  /* For (set (reg:DI N) (mem:DI ... (reg:SI N) ...)),
     if the upper part of reg N does not appear in the MEM, arrange to
     emit the move late-half first.  Otherwise, compute the MEM address
     into the upper part of N and use that as a pointer to the memory
     operand.  */
  if (optype0 == REGOP
      && (optype1 == OFFSOP || optype1 == MEMOP))
    {
      rtx testlow = gen_rtx_REG (SImode, REGNO (operands[0]));

      if (reg_overlap_mentioned_p (testlow, XEXP (operands[1], 0))
	  && reg_overlap_mentioned_p (latehalf[0], XEXP (operands[1], 0)))
	{
	  /* If both halves of dest are used in the src memory address,
	     compute the address into latehalf of dest.
	     Note that this can't happen if the dest is two data regs.  */
	compadr:
	  xops[0] = latehalf[0];
	  xops[1] = XEXP (operands[1], 0);
	  output_asm_insn ("lea %a1,%0", xops);
	  if (GET_MODE (operands[1]) == XFmode )
	    {
	      operands[1] = gen_rtx_MEM (XFmode, latehalf[0]);
	      middlehalf[1] = adjust_address (operands[1], DImode, size - 8);
	      latehalf[1] = adjust_address (operands[1], DImode, size - 4);
	    }
	  else
	    {
	      operands[1] = gen_rtx_MEM (DImode, latehalf[0]);
	      latehalf[1] = adjust_address (operands[1], DImode, size - 4);
	    }
	}
      else if (size == 12
	       && reg_overlap_mentioned_p (middlehalf[0],
					   XEXP (operands[1], 0)))
	{
	  /* Check for two regs used by both source and dest.
	     Note that this can't happen if the dest is all data regs.
	     It can happen if the dest is d6, d7, a0.
	     But in that case, latehalf is an addr reg, so
	     the code at compadr does ok.  */

	  if (reg_overlap_mentioned_p (testlow, XEXP (operands[1], 0))
	      || reg_overlap_mentioned_p (latehalf[0], XEXP (operands[1], 0)))
	    goto compadr;

	  /* JRV says this can't happen: */
	  gcc_assert (!addreg0 && !addreg1);

	  /* Only the middle reg conflicts; simply put it last.  */
	  output_asm_insn (singlemove_string (operands), operands);
	  output_asm_insn (singlemove_string (latehalf), latehalf);
	  output_asm_insn (singlemove_string (middlehalf), middlehalf);
	  return "";
	}
      else if (reg_overlap_mentioned_p (testlow, XEXP (operands[1], 0)))
	/* If the low half of dest is mentioned in the source memory
	   address, the arrange to emit the move late half first.  */
	dest_overlapped_low = 1;
    }

  /* If one or both operands autodecrementing,
     do the two words, high-numbered first.  */

  /* Likewise,  the first move would clobber the source of the second one,
     do them in the other order.  This happens only for registers;
     such overlap can't happen in memory unless the user explicitly
     sets it up, and that is an undefined circumstance.  */

  if (optype0 == PUSHOP || optype1 == PUSHOP
      || (optype0 == REGOP && optype1 == REGOP
	  && ((middlehalf[1] && REGNO (operands[0]) == REGNO (middlehalf[1]))
	      || REGNO (operands[0]) == REGNO (latehalf[1])))
      || dest_overlapped_low)
    {
      /* Make any unoffsettable addresses point at high-numbered word.  */
      if (addreg0)
	{
	  if (size == 12)
	    output_asm_insn ("addq%.l #8,%0", &addreg0);
	  else
	    output_asm_insn ("addq%.l #4,%0", &addreg0);
	}
      if (addreg1)
	{
	  if (size == 12)
	    output_asm_insn ("addq%.l #8,%0", &addreg1);
	  else
	    output_asm_insn ("addq%.l #4,%0", &addreg1);
	}

      /* Do that word.  */
      output_asm_insn (singlemove_string (latehalf), latehalf);

      /* Undo the adds we just did.  */
      if (addreg0)
	output_asm