protodma.c

这是我编一个DSP的USP的程序 调试通过

#include "d12ci.h"
//#include "mainloop.h"
#include "USBD12.h"
#include "chap_9.h"

extern CONTROL_XFER ControlData;
extern IO_REQUEST  ioRequest;
extern EPPFLAGS bEPPflags;
extern BOOL bNoRAM;
extern unsigned char EpBuf[EP2_PACKET_SIZE];

//获取固件版本号
void get_firmware_version()
{
	unsigned char i;

	i = 0x30; // firmware version number
	single_transmit((unsigned char *)&i, 1);
}

//获取端点2缓存区大小
void get_buffer_size()
{
	unsigned char i[4];

	if(bNoRAM == TRUE) {
		i[0] = EP2_PACKET_SIZE;
		i[1] = 0;
		i[2] = 0;
		i[3] = 0;
	} else {
		i[0] = 0;
		i[1] = 1;
		i[2] = 0;
		i[3] = 0;
	}
	single_transmit((unsigned char *)&i, 4);
}

void trans_data()
{
	unsigned char len,epstatus;
	if(ControlData.dataBuffer[5]==0x81)
	{
		D12_WriteEndpoint(5,ControlData.dataBuffer[3],EpBuf);
	}
	if(ControlData.dataBuffer[5]==0x80)
	{
		epstatus=D12_ReadEndpointStatus(4);
		epstatus&=0x60;
		if(epstatus==0X60)
		len=D12_ReadEndpoint(4,64,EpBuf);
	}
	single_transmit(0,0);
}

//DMA请求响应子程序
void setup_dma_request()
{
	memcpy((unsigned char *)&ioRequest + ControlData.DeviceRequest.wValue,
		ControlData.dataBuffer,
		ControlData.DeviceRequest.wLength);

	ioRequest.uSize = SWAP(ioRequest.uSize);
	ioRequest.uAddressL = SWAP(ioRequest.uAddressL);

	if(ioRequest.uSize > DMA_BUFFER_SIZE) { // Unaccepted request
		stall_ep0();//DMA设置出错
	}
	else if(bNoRAM == TRUE && ioRequest.uSize > EP2_PACKET_SIZE) {
		stall_ep0();//DMA缓冲区出错
	}
	else {
		if(bEPPflags.bits.dma_state == DMA_IDLE) {
			DISABLE;
			bEPPflags.bits.setup_dma ++;
			ENABLE;
		}
		else {
			DISABLE;
			bEPPflags.bits.dma_state = DMA_PENDING;
			ENABLE;
		}

	} // else if accepted request
}

//厂商请求处理
void read_write_register(void)
{
	unsigned char i,len,epstatus;

	if(ControlData.DeviceRequest.bmRequestType & (unsigned char)USB_ENDPOINT_DIRECTION_MASK) {

	//	if(bEPPflags.bits.verbose)
	//		printf("Read Registers: Offset = 0x%x, Length = 0x%x, Index = 0x%x.\n",
	//			ControlData.DeviceRequest.wValue,
	//			ControlData.DeviceRequest.wLength,
	//			ControlData.DeviceRequest.wIndex);

		if(ControlData.DeviceRequest.wIndex == GET_FIRMWARE_VERSION &&
			ControlData.DeviceRequest.wValue == 0 &&
			ControlData.DeviceRequest.wLength == 1)
			get_firmware_version();//获取固件版本号
		else
		if(ControlData.DeviceRequest.wIndex == GET_BUFFER_SIZE &&
			ControlData.DeviceRequest.wValue == 0 &&
			ControlData.DeviceRequest.wLength == 4)
			get_buffer_size();//获取缓冲区大小
		else
			stall_ep0();

	}	// if read register
	else{
		if(bEPPflags.bits.verbose) {

		;
		}
       #ifdef  SETUP_DMA_REQUEST
		if(ControlData.DeviceRequest.wIndex == SETUP_DMA_REQUEST &&
			ControlData.DeviceRequest.wValue == 0 &&
			ControlData.DeviceRequest.wLength == 6)
		   	{
				if(ControlData.dataBuffer[5]==0x81)
				{
					D12_WriteEndpoint(5, ControlData.dataBuffer[3], EpBuf);//发送数据
				}
				if(ControlData.dataBuffer[5]==0x80)
				{
					epstatus=D12_ReadEndpointStatus(4);
					epstatus &= 0x60;
					if (epstatus == 0x60)
						len = D12_ReadEndpoint(4, 64, EpBuf);//读取双缓冲区数据
 				}
				single_transmit(0, 0);
				//setup_dma_request();//DMA设置处理,因为未使用DMA所以屏蔽掉
			}
			
		#else 
		if(ControlData.DeviceRequest.wIndex == TRANS_REQUEST &&
		ControlData.DeviceRequest.wValue == 0 &&
		ControlData.DeviceRequest.wLength == 6)
			trans_data();
		#endif
	else
			stall_ep0();
	}	// if write register
}