gsmctl.man

Gsm手机(短信息

.TH GSMCTL 8 "##DATE##" "gsmctl v##VERSION##"
.SH NAME
gsmctl \- GSM mobile phone control program
.SH SYNOPSIS
.B gsmctl
.RB [\| \-b
.IR  baudrate \|]
.RB [\| \-\-baudrate
.IR baudrate\| ]
.RB [ \|\-d
.IR device\| ]
.RB [ \|\-\-device
.IR device\fP ]
.RB [ \|\-h\| ]
.RB [ \|\-\-help\| ]
.RB [ \|\-I
.IR "init string" \|]
.RB [ \|\-\-init
.IR "init string" \|]
.RB [ \|\-v\| ]
.RB [ \|\-\-version\| ]
.RB [ \|\-X\| ]
.RB [ \|\-\-xonxoff\| ]
.BI \-o \ operation
.RB  | \ \-\-operation
.IR operation \ |
.I parameters
.SH DESCRIPTION
.B gsmctl
can request information from or perform operations on an GSM mobile
phone.
.PP
.B gsmctl 
attaches itself to the 
.I device
given on the command line (usually an GSM modem) using the specified
.IR baudrate .  
If no
.I device
is given, the device
.I/dev/mobilephone
is used. If no 
.I baudrate
is given, a default baud rate of 38400 is used.
.PP
.B gsmctl
can be used in to modes: If no 
.B \-\-operation
option is given the
.I parameters
specify the status information to be retrieved from
the mobile phone. See the section 
.B STATUS INFORMATION
for more details. If an 
.B \-\-operation
option is given the requested
.I operation
is performed on the mobile using the
.IR parameters . 
See the section 
.B OPERATIONS
for more details.
.PP
Error messages are printed to the standard error output.  If the
program terminates on error the error code 1 is returned.
.SH OPTIONS
.TP
.BI \-b\  baudrate ,\ \-\-baudrate\  baudrate
The baud rate to use.  Defaults to 38400.
.TP
.BI \-d\  device ,\ \-\-device\  device
The device to which the GSM modem is connected. The default is
.IR /dev/mobilephone .
.TP
.B \-h,\ \-\-help
Prints an option summary.
.TP
.BI \-I\  "init string" ,\ \-\-init\  "init string"
Initialization string to send to the TA (default: "E0"). Note that the
sequence "ATZ" is sent first.
.TP
.BI \-o\  operation ,\ \-\-operation\  operation
This option is used to perform an operation on the mobile phone. Refer
to the section 
.B OPERATIONS
for more information on the available
operations and the 
.I parameters
required for each operation.
.TP
.B \-v,\ \-\-version
Prints the program version.
.TP
.B \-X,\ \-\-xonxoff
Uses software handshaking (XON/XOFF) for accessing the device.
.SH STATUS INFORMATION
If called without the 
.B \-\-operation
option 
.B gsmctl
prints out default mobile phone status information as specified by the
.I parameters
described below:
.TP 7
.B ALL
Prints all available information.
.TP 7
.B BATT
Prints out information about the current battery status. Two lines of
the form "<BATT0> text" and "<BATT1>  charge" are printed. Text may be 
of "0 ME is powered by the battery", "1 ME has a battery connected,
but is not powered by it", "2 ME does not have a battery connected",
or  "3 Recognized power fault, calls inhibited". Charge is a number in 
the range 0..100 where 0 means that the battery is empty or not
connected and 100 means full charge.
.TP 7
.B BITERR
Prints information about the current bit error rate. The output is of
form "<BITERR0>  value" where value can be of 0..7, 99 (99 means not
available or not detectable).
.TP 7
.B CLIP
This option prints a line of the form "<CLIP0> on" if caller line
identification is turned on in the network, "<CLIP0> off" otherwise.
.TP 7
.B CSET
Display info about charsets.  The output is in the form "<CSET0>
available" and "<CSET1> current", which describes the charsets
available and which is current.
.TP 7
.B CURROP
Prints information about the current operator. The output line has the
form "<CURROP0> Long name: \'xxxx\' Short name: \'yyyy\' Numeric Name: zzzz".
.TP 7
.B FLCAP
Prints out the two-letter names of available facility locks. The
meaning of standardized facility lock names is as follows:
.RS
.TP 3
.I CS
Lock control surface (eg. phone keyboard)
.TP 3
.I PS
Lock phone to SIM card (mobile phone asks password when other than
current SIM card inserted)
.TP 3
.I SC
Lock SIM card (SIM asks password in mobile phone power-up and when
this lock command issued)
.TP 3
.I AO
Barr all outgoing calls
.TP 3
.I OI
Barr outgoing international calls
.TP 3
.I OX
Barr outgoing international calls except to home country
.TP 3
.I AI
Barr all incoming calls
.TP 3
.I IR
Barr incoming calls when roaming outside the home country
.TP 3
.I NT
Barr incoming calls from numbers not stored to TA memory
.TP 3
.I NM
Barr incoming calls from numbers not stored to mobile phone memory
.TP 3
.I NS
Barr incoming calls from numbers not stored to SIM memory
.TP 3
.I NA
Barr incoming calls from numbers not stored in Any memory
.TP 3
.I AB
All Barring services (FIXME)
.TP 3
.I AG
All outGoing barring services (FIXME)
.TP 3
.I AC
All inComing barring services (FIXME)
.TP 3
.I FD
SIM fixed dialling memory feature (if PIN2 authentication has not been
done during the current session, PIN2 is required as <passwd>)
.PP
Note that mobile phones may implement facility locks not documented
here.
.RE
.TP 7
.B FLSTAT
Prints information about the status of facility locking in the mobile
phone. For each facility a line of the form "<FLSTATn> \'facilityname\'
classes" is printed. The classes may be "Voice", "Data", and/or "Fax"
depending on the class for which the facility is enabled. If "unknown"
is printed out this means that the TA is not able to report the
status. If the facility is not enabled for any class, no class
identifier is printed. See 
.B FLCAP
for information about the available two-letter names of facility
locks.
.TP 7
.B FORW
Prints information about call forwarding enabled in the mobile
phone. For each combination of reason (UnconditionalReason,
MobileBusyReason, NoReplyReason, and NotReachableReason) and class
(Voice, Data, and Fax) a line of the form "<FORWn.m> reason class
number: xxx subaddr: yyy time: zzz" is printed. The time is the number 
of seconds to wait before forwarding in case of NoReplyReason.
.TP 7
.B ME
Prints manufacturer, model, revision, and serial number of
the mobile phone (ME = mobile equipment). Output lines are numbered from 
"<ME0>" to "<ME3>".
.TP 7
.B OP
Prints information about the currently available mobile network
operators. For each operator an output line of the form "<OPn> status 
Long name: \'xxxx\' Short name: \'yyyy\' Numeric name: zzz" is returned
where status may be of:
.RS
.TP 10
.I unknown
The status of the operator is unknown.
.TP
.I current
This is the currently selected operator.
.TP
.I available
This operator is available for selection.
.TP
.I forbidden
This operator is not available for selection, ie. not
accessible with this SIM card.
.RE
.TP 7
.B PW
Facilities in the mobile phone may be protected by passwords (ie. PINs 
or PUKs). This option prints out lines of the form "<PWn>
\'facilityname\' len" for each facility for which a facility lock
password exists. See 
.B FLCAP
for information about the available two-letter names of facility
locks.
.TP 7
.B SCA
Reports the default SMS service centre address currently set in the
mobile phone.
.TP 7
.B SIG
Prints information about the current network signal
strength. The output is of the form "<SIG0> value". Following values
are possible:
.TP
.po +7
.I 0
-113 dBm or less
.TP
.I 1
-111 dBm
.TP
.I 2...30
-109... -53 dBm (in steps of 2 dBm)
.TP
.I 31
-51 dBm or greater
.TP
.I 99
not known or not detectable
.PP
.po 
.SH OPERATIONS
.TP
.BI dial\  number
Dials 
.IR number .
After dialling 
.B gsmctl
waits for a <CR> keypress to terminate.
.PP
.B forw
.IR mode\ reason\ number\  [\| facilityclass\| ]\ [ forwardtime ]
.RS
Changes the call forwarding behaviour in the network. 
.I mode
can be any of:
.RS 3
.I disable
Call forwarding is disabled.
.PP
.I enable
Call forwarding is enabled. The call forwarding reason, number, and
(optionally) forwardtime must be registered beforehand.
.PP
.I register
This registers the call forwarding reason, number, and forwardtime in
the network.
.PP
.I erase
This is the counterpart to register. It erase the call forwarding info 
in the network.
.RE
.PP
.I reason
can be any of:
.RS 3
.I unconditional
This applies to every call.
.PP
.I mobilebusy
The mobile phone is busy.
.PP
.I noreply
The call is not answered in \fIforwardtime\fP seconds.
.PP
.I notreachable
Mobile phone cannot be reached (ie. switched off).
.PP
.I all
This refers to all forwarding reasons.
.PP
.I allconditional
This refers to all conditional forward reasons 
.RI ( mobilebusy ,\  noreply ,\  notreachable ).
.RE
.PP
.I number
is the number the incoming call is forwarded to. See the explanation
for 
.I lock
operation for the meaning of 
.IR facilityclass .
The default for 
.I forwardtime
is 20 seconds if omitted. 
.I forwardtime
can be in the range 1..30.
.RE
.PP
.B lock
.IR facility\  [\| facilityclass \|]\ [\| passwd \|]
.RS 
Locks the named facility. Use 
.BI gsmctl\  flcap
to get a list of supported facilities. The 
.I facilityclass
can be any of:
.RS 3
.I all
Voice, data, and fax.
.PP
.I v\ vf\ vd\ f\ fd\ d
Any combination of voice, data and fax.
.RE
.PP
The default is \fIall\fP if \fIfacilityclass\fP is omitted. The
\fIpasswd\fP is password for the facility. If no password is given
this parameter can be omitted.
.RE
.PP
.BI setop\  opmode\ numericname
.RS
Sets the current operator to 
.IR numericname . 
Use 
.BI gsmctl\  op
to get a list of operators with their numeric codes. 
.I opmode
can be any of:
.RS 3
.I automatic
.PP
.I manual
.PP
.I deregister
Deregister from network.
.PP
.I manualautomatic
If manual selection fails, automatic mode is entered.
.RE
.RE
.PP
.B setpw
.IR facility\  [\| oldpasswd\| ]\ [\| newpasswd\| ]
.RS
Sets the password for the facility. If one of the passwords is omitted 
this means that the facility has no password protection. Passwords are 
PIN1, PIN2, PUK etc.
.RE
.TP
.BI setsca\  service\ centre\ address
Sets the default SMS service centre address.
.PP
.B unlock
.IR facility\  [\| facilityclass\| ]\ [ \|passwd\| ]
.RS
This is the reverse operation to \fBlock\fP. See above for a
description of the parameters.
.RE
.SH EXAMPLES
The following invocation of 
.I gsmctl
prints out all available status information for the mobile phone
connected to
.B /dev/mobilephone
.PP
.nf
.IP "" 3 
gsmctl all
.fi
.PP
The output could look like (lines edited to fit):
.RS 3
.PP
.PD 0
<ME0>  Manufacturer: SIEMENS
.HP
<ME1>  Model: S10
.HP
<ME2>  Revision: 06
.HP
<ME3>  Serial Number: 448058511817585
.HP
<OP0>  Status: available  Long name: 'D1-TELEKOM' Short name: '' Numeric name: 26201
.HP
<OP1>  Status: forbidden  Long name: 'D2  PRIVAT' Short name: '' Numeric name: 26202
.HP
<CURROP0>  Long name: 'D1-TELEKOM'   Short name: '' Numeric name: 26201 Mode: automatic
.HP
<FLSTAT0>  'CS'
.HP
<FLSTAT1>  'PS'
.HP
<FLSTAT2>  'SC'  Voice  Data  Fax
.HP
<FLSTAT3>  'AO'
.HP
<FLSTAT4>  'OI'
.HP
<FLSTAT5>  'OX'
.HP
<FLSTAT6>  'AI'
.HP
<FLSTAT7>  'IR'
.HP
<FLCAP0>  'CS' 'PS' 'SC' 'AO' 'OI' 'OX' 'AI' 'IR' 'AB' 'AG' 'AC' 
.HP
<PW0>  'PS' 8
.HP
<PW1>  'SC' 8
.HP
<PW2>  'AO' 4
.HP
<PW3>  'OI' 4
.HP
<PW4>  'OX' 4
.HP
<PW5>  'AI' 4
.HP
<PW6>  'IR' 4
.HP
<PW7>  'AB' 4
.HP
<PW8>  'AG' 4
.HP
<PW9>  'AC' 4
.HP
<CLIP0>  on
.HP
<FORW0.0>  UnconditionalReason  Voice  inactive number:   subaddr:  time: -1
.HP
<FORW0.1>  UnconditionalReason  Data  inactive number:   subaddr:  time: -1
.HP
<FORW0.2>  UnconditionalReason  Fax  inactive number:   subaddr:  time: -1
.HP
<FORW1.0>  MobileBusyReason  Voice  active number: [phone]  subaddr:   time: -1
.HP
<FORW1.1>  MobileBusyReason  Data  inactive number:   subaddr:  time: -1
.HP
<FORW1.2>  MobileBusyReason  Fax  inactive number:   subaddr:  time: -1
.HP
<FORW2.0>  NoReplyReason  Voice  active number: [phone]  subaddr:   time: 20
.HP
<FORW2.1>  NoReplyReason  Data  inactive number:   subaddr:  time: -1
.HP
<FORW2.2>  NoReplyReason  Fax  inactive number:   subaddr:  time: -1
.HP
<FORW3.0>  NotReachableReason  Voice  active number: [phone]  subaddr:  time: -1
.HP
<FORW3.1>  NotReachableReason  Data  inactive number:  subaddr:  time: -1
.HP
<FORW3.2>  NotReachableReason  Fax  inactive number:  subaddr:  time: -1
.HP
<BATT0>   0 ME is powered by the battery
.HP
<BATT1>  100
.HP
<BITERR0>  0
.HP
<SIG0>  19
.RE
.PD
.PP
The following locks the keys on the mobile phone:
.nf
.IP "" 3
gsmctl -o lock cs
.fi
.PP
This changes the SIM card PIN from 1234 to 2345:
.nf
.IP "" 3
gsmctl -o setpw sc 1234 2345
.fi
.PP
Switch off all call forwarding (actually erase the numbers):
.nf
.IP "" 3
gsmctl -o forw erase all
.fi
.PP
Switch on call forwarding to German D1 voice box:
.nf
.IP "" 3
gsmctl -o forw register notreachable 3313
gsmctl -o forw enable notreachable
.fi
.PP
.SH FILES
.TP
.B /dev/mobilephone
Default mobile phone device.
.SH AUTHOR
Peter Hofmann <[e-mail]>
.SH BUGS
Report bugs to [e-mail].  Include a complete, self-ncontained
example that will allow the bug to be reproduced, and say which
version of \fIgsmctl\fP you are using.
.SH COPYRIGHT
Copyright \(co 1999 Peter Hofmann
.PP
.B gsmctl
is free software; you can redistribute it and/or modify it under the
terms of the GNU Library General Public License as published by the
Free Software Foundation; either version 2, or (at your option) any
later version.
.PP
.B gsmctl
is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE.  See the GNU Library General Public
License for more details.
.PP
You should have received a copy of the GNU Library General Public
License along with 
.BR gsmctl ; 
see the file COPYING.  If not, write to the Free Software Foundation,
675 Mass Ave, Cambridge, MA 02139, USA.
.SH "SEE ALSO"
.BR gsminfo (7),
.BR gsmpb (1),
.BR gsmsendsms (1),
.BR gsmsmsd (8),
.BR gsmsmsstore (1).