s12sermon2r1.def

Freescale HCS12 单片机系统监控

;*********************************************************************
;* One device specific NVM definition below should be uncommented
;*********************************************************************
Dx512:
;EEpromStart:   equ   $0400         ;eeprom start
;EEpromEnd:     equ   $07FF         ;eeprom end (rest is hidden)
;RamStart:      equ   $0800         ;first RAM location
;SectorSize:    equ   $0400         ;Flash sector size
;FlashBlks:     equ   $04           ;# of flash blks
;LowestPage:    equ   $20           ;lowest page
;PagesBlk:      equ   $08           ;pages per block
;softwareID4:   equ   $0400		      ;device ID #

Dx256:
EEpromStart:   equ   $0400         ;eeprom start
EEpromEnd:     equ   $0FFF         ;eeprom end
RamStart:      equ   $1000         ;first RAM location
SectorSize:    equ   $0200         ;Flash sector size
FlashBlks:     equ   $04           ;# of flash blks
LowestPage:    equ   $30           ;lowest page
PagesBlk:      equ   $04           ;pages per block
softwareID4:   equ   $0011		      ;device ID #

Dx128:
;EEpromStart:   equ   $0800         ;eeprom start
;EEpromEnd:     equ   $0FFF         ;eeprom end
;RamStart:      equ   $2000         ;first RAM location
;FlashBlks:     equ   $02           ;# of flash blks
;SectorSize:    equ   $0200         ;Flash sector size
;LowestPage:    equ   $38           ;lowest page
;PagesBlk:      equ   $04           ;pages per block
;softwareID4:   equ   $0110		    ;device ID #

Dx64:
;EEpromStart:   equ   $0C00         ;eeprom start
;EEpromEnd:     equ   $0FFF         ;eeprom End
;RamStart:      equ   $3000         ;first RAM location
;FlashBlks:     equ   $01           ;# of flash blks
;SectorSize:    equ   $0200         ;Flash sector size
;LowestPage:    equ   $3C           ;lowest page
;PagesBlk:      equ   $04           ;pages per block
;softwareID4:   equ   $0201		    ;device ID #

E128:
;EEpromStart:   equ   $0000         ;eeprom Start (no EEprom)
;EEpromEnd:     equ   $0000         ;eeprom End  
;RamStart:      equ   $2000         ;first RAM location
;FlashBlks:     equ   $01           ;# of flash blks
;SectorSize:    equ   $0400         ;Flash sector size
;LowestPage:    equ   $38           ;lowest page
;PagesBlk:      equ   $08           ;pages per block
;softwareID4:   equ   $5102		    ;device ID #

C32:
;EEpromStart:   equ   $0000          ;eeprom start (no EEprom)
;EEpromEnd:     equ   $0000          ;eeprom End
;RamStart:      equ   $3800          ;first RAM location
;FlashBlks:     equ   $01            ;# of flash blks
;SectorSize:    equ   $0200          ;Flash sector size
;LowestPage:    equ   $3E            ;lowest page
;PagesBlk:      equ   $02            ;pages per block
;softwareID4:   equ   $3300		      ;device ID #

Dx32:
;EEpromStart:   equ   $0C00         ;eeprom start
;EEpromEnd:     equ   $0FFF         ;eeprom End
;RamStart:      equ   $3800         ;first RAM location
;FlashBlks:     equ   $01           ;# of flash blks
;SectorSize:    equ   $0200         ;Flash sector size
;LowestPage:    equ   $3E           ;lowest page
;PagesBlk:      equ   $02           ;pages per block
;softwareID4:   equ   $0300		      ;device ID #
																	  
H256:
;EEpromStart:    equ   $0400         ;eeprom start
;EEpromEnd:      equ   $0FFF         ;eeprom end
;RamStart:       equ   $1000         ;first RAM location
;SectorSize:     equ   $0200         ;Flash sector size
;FlashBlks:      equ   $04           ;# of flash blks
;LowestPage:     equ   $30           ;lowest page
;PagesBlk:       equ   $04           ;pages per block
;softwareID4:    equ   $1001		      ;device ID #

;*********************************************************************
;* One application specific Osc definition below should be uncommented
;* If Additonal eneries are required initSYNR and initREFDV must be
;* set for 24MHz PLL frequency. SCI communication problems will result
;* at other frequencies.
;*********************************************************************
;OscFreq:     equ   4000           ;Enter Osc speed
;initSYNR:    equ   $05            ; mult by synr + 1 = 6 (24MHz)
;initREFDV:   equ   $00            ;
;---------------------------------------------------------------------
OscFreq:      equ   8000           ;Enter Osc speed
initSYNR:     equ   $02            ; mult by synr + 1 = 3 (24MHz)
initREFDV:    equ   $00            ;
;---------------------------------------------------------------------
;OscFreq:     equ   16000          ;Enter Osc speed
;initSYNR:    equ   $02            ; mult by synr + 1 = 3/2 (24MHz)
;initREFDV:   equ   $01            ; divide by Refdiv + 1
;---------------------------------------------------------------------
;OscFreq:     equ   25000          ;Enter Osc speed
;initSYNR:    equ   $00            ; mult by synr + 1 = 1 (25MHz)
;initREFDV:   equ   $00            ; divide by Refdiv + 1

;*********************************************************************
;* One application specific Run Load Switch definition below should be 
;* uncommented. This defininition sets the placement of the switch to 
;* force entery into the monitor. The switch sould be configure such
;* that the load position applies a logic zero to the selected pin.
;*********************************************************************
;---------------------------------------------------------------------
;SwPort:      equ    PTQ           ;pushbutton sw connected to port Q
;Switch:      equ    PTQ0          ;switch connected to PTQ bit-5
;SwPullup:    equ    PERQ          ;pullup enable for sw port
;mSwPullup:   equ	   PTQ0          ;Mask value to enable for sw port
;---------------------------------------------------------------------
;SwPort:      equ    PTP           ;pushbutton sw connected to port P
;Switch:      equ    PTP5          ;switch connected to PTP bit-5
;SwPullup:    equ    PERP          ;pullup enable for sw port
;mSwPullup:   equ	   PTP5          ;Mask value to enable for sw port
;---------------------------------------------------------------------
SwPort:      equ    PORTA         ;pushbutton sw connected to port A
Switch:      equ    PTA6          ;switch connected to PTA bit-6
SwPullup:    equ    PUCR          ;pullup enable for sw port
mSwPullup:   equ	   PUPAE         ;Mask value to enable for sw port
;---------------------------------------------------------------------
;SwPort:      equ    PORTB         ;pushbutton sw connected to port B
;Switch:      equ    PTB4          ;switch connected to PTB bit-4
;Switch:      equ    PTB0          ;switch connected to PTB bit-0
;SwPullup:    equ    PUCR          ;pullup enable for sw port
;mSwPullup:   equ	   PUPBE         ;Mask value to enable for sw port
;---------------------------------------------------------------------
;SwPort:      equ    PTL           ;pushbutton sw connected to port P
;Switch:      equ    PTL6          ;switch connected to PTP bit-5
;SwPullup:    equ    PERL          ;pullup enable for sw port
;mSwPullup:   equ	   PTL6          ;Mask value to enable for sw port
;---------------------------------------------------------------------
;SwPort:      equ    PTP           ;pushbutton sw connected to port P
;Switch:      equ    PTP0          ;switch connected to PTP bit-0
;SwPullup:    equ    PERP          ;pullup enable for sw port
;mSwPullup:   equ	   PTP0          ;Mask value to enable for sw port
;---------------------------------------------------------------------
;---------------------------------------------------------------------
;SwPort:      equ    PTG           ;pushbutton sw connected to port G
;Switch:      equ    PTG4          ;switch connected to PTP bit-4
;SwPullup:    equ    PERG          ;pullup enable for sw port
;mSwPullup:   equ	   PTG4          ;Mask value to enable for sw port
;---------------------------------------------------------------------

AllowSci0     equ    $0			   ;set to one to allow user application
								               ; use of sci0. The monitor will not 
								               ; Be able to break into user code if
								               ; this is set. This will effect debugging