zlib.h

PIXIL is a small footprint operating environment, complete with PDA PIM applications, a browser and

   value depends on the compression method), inflateInit determines the
   compression method from the zlib header and allocates all data structures
   accordingly; otherwise the allocation will be deferred to the first call of
   inflate.  If zalloc and zfree are set to Z_NULL, inflateInit updates them to
   use default allocation functions.

     inflateInit returns Z_OK if success, Z_MEM_ERROR if there was not enough
   memory, Z_VERSION_ERROR if the zlib library version is incompatible with the
   version assumed by the caller.  msg is set to null if there is no error
   message. inflateInit does not perform any decompression apart from reading
   the zlib header if present: this will be done by inflate().  (So next_in and
   avail_in may be modified, but next_out and avail_out are unchanged.)
*/


ZEXTERN int ZEXPORT inflate OF((z_streamp strm, int flush));
/*
    inflate decompresses as much data as possible, and stops when the input
  buffer becomes empty or the output buffer becomes full. It may some
  introduce some output latency (reading input without producing any output)
  except when forced to flush.

  The detailed semantics are as follows. inflate performs one or both of the
  following actions:

  - Decompress more input starting at next_in and update next_in and avail_in
    accordingly. If not all input can be processed (because there is not
    enough room in the output buffer), next_in is updated and processing
    will resume at this point for the next call of inflate().

  - Provide more output starting at next_out and update next_out and avail_out
    accordingly.  inflate() provides as much output as possible, until there
    is no more input data or no more space in the output buffer (see below
    about the flush parameter).

  Before the call of inflate(), the application should ensure that at least
  one of the actions is possible, by providing more input and/or consuming
  more output, and updating the next_* and avail_* values accordingly.
  The application can consume the uncompressed output when it wants, for
  example when the output buffer is full (avail_out == 0), or after each
  call of inflate(). If inflate returns Z_OK and with zero avail_out, it
  must be called again after making room in the output buffer because there
  might be more output pending.

    If the parameter flush is set to Z_SYNC_FLUSH, inflate flushes as much
  output as possible to the output buffer. The flushing behavior of inflate is
  not specified for values of the flush parameter other than Z_SYNC_FLUSH
  and Z_FINISH, but the current implementation actually flushes as much output
  as possible anyway.

    inflate() should normally be called until it returns Z_STREAM_END or an
  error. However if all decompression is to be performed in a single step
  (a single call of inflate), the parameter flush should be set to
  Z_FINISH. In this case all pending input is processed and all pending
  output is flushed; avail_out must be large enough to hold all the
  uncompressed data. (The size of the uncompressed data may have been saved
  by the compressor for this purpose.) The next operation on this stream must
  be inflateEnd to deallocate the decompression state. The use of Z_FINISH
  is never required, but can be used to inform inflate that a faster routine
  may be used for the single inflate() call.

     If a preset dictionary is needed at this point (see inflateSetDictionary
  below), inflate sets strm-adler to the adler32 checksum of the
  dictionary chosen by the compressor and returns Z_NEED_DICT; otherwise 
  it sets strm->adler to the adler32 checksum of all output produced
  so far (that is, total_out bytes) and returns Z_OK, Z_STREAM_END or
  an error code as described below. At the end of the stream, inflate()
  checks that its computed adler32 checksum is equal to that saved by the
  compressor and returns Z_STREAM_END only if the checksum is correct.

    inflate() returns Z_OK if some progress has been made (more input processed
  or more output produced), Z_STREAM_END if the end of the compressed data has
  been reached and all uncompressed output has been produced, Z_NEED_DICT if a
  preset dictionary is needed at this point, Z_DATA_ERROR if the input data was
  corrupted (input stream not conforming to the zlib format or incorrect
  adler32 checksum), Z_STREAM_ERROR if the stream structure was inconsistent
  (for example if next_in or next_out was NULL), Z_MEM_ERROR if there was not
  enough memory, Z_BUF_ERROR if no progress is possible or if there was not
  enough room in the output buffer when Z_FINISH is used. In the Z_DATA_ERROR
  case, the application may then call inflateSync to look for a good
  compression block.
*/


ZEXTERN int ZEXPORT inflateEnd OF((z_streamp strm));
/*
     All dynamically allocated data structures for this stream are freed.
   This function discards any unprocessed input and does not flush any
   pending output.

     inflateEnd returns Z_OK if success, Z_STREAM_ERROR if the stream state
   was inconsistent. In the error case, msg may be set but then points to a
   static string (which must not be deallocated).
*/

                        /* Advanced functions */

/*
    The following functions are needed only in some special applications.
*/

/*   
ZEXTERN int ZEXPORT deflateInit2 OF((z_streamp strm,
                                     int  level,
                                     int  method,
                                     int  windowBits,
                                     int  memLevel,
                                     int  strategy));

     This is another version of deflateInit with more compression options. The
   fields next_in, zalloc, zfree and opaque must be initialized before by
   the caller.

     The method parameter is the compression method. It must be Z_DEFLATED in
   this version of the library.

     The windowBits parameter is the base two logarithm of the window size
   (the size of the history buffer).  It should be in the range 8..15 for this
   version of the library. Larger values of this parameter result in better
   compression at the expense of memory usage. The default value is 15 if
   deflateInit is used instead.

     The memLevel parameter specifies how much memory should be allocated
   for the internal compression state. memLevel=1 uses minimum memory but
   is slow and reduces compression ratio; memLevel=9 uses maximum memory
   for optimal speed. The default value is 8. See zconf.h for total memory
   usage as a function of windowBits and memLevel.

     The strategy parameter is used to tune the compression algorithm. Use the
   value Z_DEFAULT_STRATEGY for normal data, Z_FILTERED for data produced by a
   filter (or predictor), or Z_HUFFMAN_ONLY to force Huffman encoding only (no
   string match).  Filtered data consists mostly of small values with a
   somewhat random distribution. In this case, the compression algorithm is
   tuned to compress them better. The effect of Z_FILTERED is to force more
   Huffman coding and less string matching; it is somewhat intermediate
   between Z_DEFAULT and Z_HUFFMAN_ONLY. The strategy parameter only affects
   the compression ratio but not the correctness of the compressed output even
   if it is not set appropriately.

      deflateInit2 returns Z_OK if success, Z_MEM_ERROR if there was not enough
   memory, Z_STREAM_ERROR if a parameter is invalid (such as an invalid
   method). msg is set to null if there is no error message.  deflateInit2 does
   not perform any compression: this will be done by deflate().
*/
                            
ZEXTERN int ZEXPORT deflateSetDictionary OF((z_streamp strm,
                                             const Bytef *dictionary,
                                             uInt  dictLength));
/*
     Initializes the compression dictionary from the given byte sequence
   without producing any compressed output. This function must be called
   immediately after deflateInit, deflateInit2 or deflateReset, before any
   call of deflate. The compressor and decompressor must use exactly the same
   dictionary (see inflateSetDictionary).

     The dictionary should consist of strings (byte sequences) that are likely
   to be encountered later in the data to be compressed, with the most commonly
   used strings preferably put towards the end of the dictionary. Using a
   dictionary is most useful when the data to be compressed is short and can be
   predicted with good accuracy; the data can then be compressed better than
   with the default empty dictionary.

     Depending on the size of the compression data structures selected by
   deflateInit or deflateInit2, a part of the dictionary may in effect be
   discarded, for example if the dictionary is larger than the window size in
   deflate or deflate2. Thus the strings most likely to be useful should be
   put at the end of the dictionary, not at the front.

     Upon return of this function, strm->adler is set to the Adler32 value
   of the dictionary; the decompressor may later use this value to determine
   which dictionary has been used by the compressor. (The Adler32 value
   applies to the whole dictionary even if only a subset of the dictionary is
   actually used by the compressor.)

     deflateSetDictionary returns Z_OK if success, or Z_STREAM_ERROR if a
   parameter is invalid (such as NULL dictionary) or the stream state is
   inconsistent (for example if deflate has already been called for this stream
   or if the compression method is bsort). deflateSetDictionary does not
   perform any compression: this will be done by deflate().
*/

ZEXTERN int ZEXPORT deflateCopy OF((z_streamp dest,
                                    z_streamp source));
/*
     Sets the destination stream as a complete copy of the source stream.

     This function can be useful when several compression strategies will be
   tried, for example when there are several ways of pre-processing the input
   data with a filter. The streams that will be discarded should then be freed
   by calling deflateEnd.  Note that deflateCopy duplicates the internal
   compression state which can be quite large, so this strategy is slow and
   can consume lots of memory.

     deflateCopy returns Z_OK if success, Z_MEM_ERROR if there was not
   enough memory, Z_STREAM_ERROR if the source stream state was inconsistent
   (such as zalloc being NULL). msg is left unchanged in both source and
   destination.
*/

ZEXTERN int ZEXPORT deflateReset OF((z_streamp strm));
/*
     This function is equivalent to deflateEnd followed by deflateInit,
   but does not free and reallocate all the internal compression state.
   The stream will keep the same compression level and any other attributes
   that may have been set by deflateInit2.

      deflateReset returns Z_OK if success, or Z_STREAM_ERROR if the source
   stream state was inconsistent (such as zalloc or state being NULL).
*/

ZEXTERN int ZEXPORT deflateParams OF((z_streamp strm,
				      int level,
				      int strategy));
/*
     Dynamically update the compression level and compression strategy.  The
   interpretation of level and strategy is as in deflateInit2.  This can be
   used to switch between compression and straight copy of the input data, or
   to switch to a different kind of input data requiring a different
   strategy. If the compression level is changed, the input available so far
   is compressed with the old level (and may be flushed); the new level will
   take effect only at the next call of deflate().

     Before the call of deflateParams, the stream state must be set as for
   a call of deflate(), since the currently available input may have to
   be compressed and flushed. In particular, strm->avail_out must be non-zero.

     deflateParams returns Z_OK if success, Z_STREAM_ERROR if the source
   stream state was inconsistent or if a parameter was invalid, Z_BUF_ERROR
   if strm->avail_out was zero.
*/

/*   
ZEXTERN int ZEXPORT inflateInit2 OF((z_streamp strm,
                                     int  windowBits));

     This is another version of inflateInit with an extra parameter. The
   fields next_in, avail_in, zalloc, zfree and opaque must be initialized
   before by the caller.

     The windowBits parameter is the base two logarithm of the maximum window
   size (the size of the history buffer).  It should be in the range 8..15 for
   this version of the library. The default value is 15 if inflateInit is used
   instead. If a compressed stream with a larger window size is given as
   input, inflate() will return with the error code Z_DATA_ERROR instead of
   trying to allocate a larger window.

      inflateInit2 returns Z_OK if success, Z_MEM_ERROR if there was not enough
   memory, Z_STREAM_ERROR if a parameter is invalid (such as a negative
   memLevel). msg is set to null if there is no error message.  inflateInit2
   does not perform any decompression apart from reading the zlib header if
   present: this will be done by inflate(). (So next_in and avail_in may be
   modified, but next_out and avail_out are unchanged.)
*/

ZEXTERN int ZEXPORT inflateSetDictionary OF((z_streamp strm,
                                             const Bytef *dictionary,
                                             uInt  dictLength));
/*
     Initializes the decompression dictionary from the given uncompressed byte
   sequence. This function must be called immediately after a call of inflate
   if this call returned Z_NEED_DICT. The dictionary chosen by the compressor
   can be determined from the Adler32 value returned by this call of
   inflate. The compressor and decompressor must use exactly the same
   dictionary (see deflateSetDictionary).

     inflateSetDictionary returns Z_OK if success, Z_STREAM_ERROR if a
   parameter is invalid (such as NULL dictionary) or the stream state is
   inconsistent, Z_DATA_ERROR if the given dictionary doesn't match the
   expected one (incorrect Adler32 value). inflateSetDictionary does not
   perform any decompression: this will be done by subsequent calls of
   inflate().
*/

ZEXTERN int ZEXPORT inflateSync OF((z_streamp strm));
/* 
    Skips invalid compressed data until a full flush point (see above the
  description of deflate with Z_FULL_FLUSH) can be found, or until all
  available input is skipped. No output is provided.

    inflateSync returns Z_OK if a full flush point has been found, Z_BUF_ERROR
  if no more input was provided, Z_DATA_ERROR if no flush point has been found,
  or Z_STREAM_ERROR if the stream structure was inconsistent. In the success
  case, the application may save the current current value of total_in which
  indicates where valid compressed data was found. In the error case, the
  application may repeatedly call inflateSync, providing more input each time,
  until success or end of the input data.
*/

ZEXTERN int ZEXPORT inflateReset OF((z_streamp strm));
/*
     This function is equivalent to inflateEnd followed by inflateInit,
   but does not free and reallocate all the internal decompression state.
   The stream will keep attributes that may have been set by inflateInit2.

      inflateReset returns Z_OK if success, or Z_STREAM_ERROR if the source
   stream state was inconsistent (such as zalloc or state being NULL).
*/