pxa-regs.h

linux-2.6.15.6

#define UDCCRW          __REG(0x40600458) /* Configuration register EPW */
#define UDCCRX          __REG(0x4060045C) /* Configuration register EPX */

#define UDCCONR_CN	(0x03 << 25)	/* Configuration Number */
#define UDCCONR_CN_S	(25)
#define UDCCONR_IN	(0x07 << 22)	/* Interface Number */
#define UDCCONR_IN_S	(22)
#define UDCCONR_AISN	(0x07 << 19)	/* Alternate Interface Number */
#define UDCCONR_AISN_S	(19)
#define UDCCONR_EN	(0x0f << 15)	/* Endpoint Number */
#define UDCCONR_EN_S	(15)
#define UDCCONR_ET	(0x03 << 13)	/* Endpoint Type: */
#define UDCCONR_ET_S	(13)
#define UDCCONR_ET_INT	(0x03 << 13)	/*   Interrupt */
#define UDCCONR_ET_BULK	(0x02 << 13)	/*   Bulk */
#define UDCCONR_ET_ISO	(0x01 << 13)	/*   Isochronous */
#define UDCCONR_ET_NU	(0x00 << 13)	/*   Not used */
#define UDCCONR_ED	(1 << 12)	/* Endpoint Direction */
#define UDCCONR_MPS	(0x3ff << 2)	/* Maximum Packet Size */
#define UDCCONR_MPS_S	(2)
#define UDCCONR_DE	(1 << 1)	/* Double Buffering Enable */
#define UDCCONR_EE	(1 << 0)	/* Endpoint Enable */


#define UDC_INT_FIFOERROR  (0x2)
#define UDC_INT_PACKETCMP  (0x1)

#define UDC_FNR_MASK     (0x7ff)

#define UDCCSR_WR_MASK   (UDCCSR_DME|UDCCSR_FST)
#define UDC_BCR_MASK    (0x3ff)
#endif

/*
 * Fast Infrared Communication Port
 */

#define FICP		__REG(0x40800000)  /* Start of FICP area */
#define ICCR0		__REG(0x40800000)  /* ICP Control Register 0 */
#define ICCR1		__REG(0x40800004)  /* ICP Control Register 1 */
#define ICCR2		__REG(0x40800008)  /* ICP Control Register 2 */
#define ICDR		__REG(0x4080000c)  /* ICP Data Register */
#define ICSR0		__REG(0x40800014)  /* ICP Status Register 0 */
#define ICSR1		__REG(0x40800018)  /* ICP Status Register 1 */

#define ICCR0_AME	(1 << 7)	/* Adress match enable */
#define ICCR0_TIE	(1 << 6)	/* Transmit FIFO interrupt enable */
#define ICCR0_RIE	(1 << 5)	/* Recieve FIFO interrupt enable */
#define ICCR0_RXE	(1 << 4)	/* Receive enable */
#define ICCR0_TXE	(1 << 3)	/* Transmit enable */
#define ICCR0_TUS	(1 << 2)	/* Transmit FIFO underrun select */
#define ICCR0_LBM	(1 << 1)	/* Loopback mode */
#define ICCR0_ITR	(1 << 0)	/* IrDA transmission */

#define ICCR2_RXP       (1 << 3)	/* Receive Pin Polarity select */
#define ICCR2_TXP       (1 << 2)	/* Transmit Pin Polarity select */
#define ICCR2_TRIG	(3 << 0)	/* Receive FIFO Trigger threshold */
#define ICCR2_TRIG_8    (0 << 0)	/* 	>= 8 bytes */
#define ICCR2_TRIG_16   (1 << 0)	/*	>= 16 bytes */
#define ICCR2_TRIG_32   (2 << 0)	/*	>= 32 bytes */

#ifdef CONFIG_PXA27x
#define ICSR0_EOC	(1 << 6)	/* DMA End of Descriptor Chain */
#endif
#define ICSR0_FRE	(1 << 5)	/* Framing error */
#define ICSR0_RFS	(1 << 4)	/* Receive FIFO service request */
#define ICSR0_TFS	(1 << 3)	/* Transnit FIFO service request */
#define ICSR0_RAB	(1 << 2)	/* Receiver abort */
#define ICSR0_TUR	(1 << 1)	/* Trunsmit FIFO underun */
#define ICSR0_EIF	(1 << 0)	/* End/Error in FIFO */

#define ICSR1_ROR	(1 << 6)	/* Receiver FIFO underrun  */
#define ICSR1_CRE	(1 << 5)	/* CRC error */
#define ICSR1_EOF	(1 << 4)	/* End of frame */
#define ICSR1_TNF	(1 << 3)	/* Transmit FIFO not full */
#define ICSR1_RNE	(1 << 2)	/* Receive FIFO not empty */
#define ICSR1_TBY	(1 << 1)	/* Tramsmiter busy flag */
#define ICSR1_RSY	(1 << 0)	/* Recevier synchronized flag */


/*
 * Real Time Clock
 */

#define RCNR		__REG(0x40900000)  /* RTC Count Register */
#define RTAR		__REG(0x40900004)  /* RTC Alarm Register */
#define RTSR		__REG(0x40900008)  /* RTC Status Register */
#define RTTR		__REG(0x4090000C)  /* RTC Timer Trim Register */
#define PIAR		__REG(0x40900038)  /* Periodic Interrupt Alarm Register */

#define RTSR_PICE	(1 << 15)	/* Periodic interrupt count enable */
#define RTSR_PIALE	(1 << 14)	/* Periodic interrupt Alarm enable */
#define RTSR_HZE	(1 << 3)	/* HZ interrupt enable */
#define RTSR_ALE	(1 << 2)	/* RTC alarm interrupt enable */
#define RTSR_HZ		(1 << 1)	/* HZ rising-edge detected */
#define RTSR_AL		(1 << 0)	/* RTC alarm detected */


/*
 * OS Timer & Match Registers
 */

#define OSMR0		__REG(0x40A00000)  /* */
#define OSMR1		__REG(0x40A00004)  /* */
#define OSMR2		__REG(0x40A00008)  /* */
#define OSMR3		__REG(0x40A0000C)  /* */
#define OSMR4		__REG(0x40A00080)  /* */
#define OSCR		__REG(0x40A00010)  /* OS Timer Counter Register */
#define OSCR4		__REG(0x40A00040)  /* OS Timer Counter Register */
#define OMCR4		__REG(0x40A000C0)  /* */
#define OSSR		__REG(0x40A00014)  /* OS Timer Status Register */
#define OWER		__REG(0x40A00018)  /* OS Timer Watchdog Enable Register */
#define OIER		__REG(0x40A0001C)  /* OS Timer Interrupt Enable Register */

#define OSSR_M3		(1 << 3)	/* Match status channel 3 */
#define OSSR_M2		(1 << 2)	/* Match status channel 2 */
#define OSSR_M1		(1 << 1)	/* Match status channel 1 */
#define OSSR_M0		(1 << 0)	/* Match status channel 0 */

#define OWER_WME	(1 << 0)	/* Watchdog Match Enable */

#define OIER_E3		(1 << 3)	/* Interrupt enable channel 3 */
#define OIER_E2		(1 << 2)	/* Interrupt enable channel 2 */
#define OIER_E1		(1 << 1)	/* Interrupt enable channel 1 */
#define OIER_E0		(1 << 0)	/* Interrupt enable channel 0 */


/*
 * Pulse Width Modulator
 */

#define PWM_CTRL0	__REG(0x40B00000)  /* PWM 0 Control Register */
#define PWM_PWDUTY0	__REG(0x40B00004)  /* PWM 0 Duty Cycle Register */
#define PWM_PERVAL0	__REG(0x40B00008)  /* PWM 0 Period Control Register */

#define PWM_CTRL1	__REG(0x40C00000)  /* PWM 1Control Register */
#define PWM_PWDUTY1	__REG(0x40C00004)  /* PWM 1 Duty Cycle Register */
#define PWM_PERVAL1	__REG(0x40C00008)  /* PWM 1 Period Control Register */


/*
 * Interrupt Controller
 */

#define ICIP		__REG(0x40D00000)  /* Interrupt Controller IRQ Pending Register */
#define ICMR		__REG(0x40D00004)  /* Interrupt Controller Mask Register */
#define ICLR		__REG(0x40D00008)  /* Interrupt Controller Level Register */
#define ICFP		__REG(0x40D0000C)  /* Interrupt Controller FIQ Pending Register */
#define ICPR		__REG(0x40D00010)  /* Interrupt Controller Pending Register */
#define ICCR		__REG(0x40D00014)  /* Interrupt Controller Control Register */


/*
 * General Purpose I/O
 */

#define GPLR0		__REG(0x40E00000)  /* GPIO Pin-Level Register GPIO<31:0> */
#define GPLR1		__REG(0x40E00004)  /* GPIO Pin-Level Register GPIO<63:32> */
#define GPLR2		__REG(0x40E00008)  /* GPIO Pin-Level Register GPIO<80:64> */

#define GPDR0		__REG(0x40E0000C)  /* GPIO Pin Direction Register GPIO<31:0> */
#define GPDR1		__REG(0x40E00010)  /* GPIO Pin Direction Register GPIO<63:32> */
#define GPDR2		__REG(0x40E00014)  /* GPIO Pin Direction Register GPIO<80:64> */

#define GPSR0		__REG(0x40E00018)  /* GPIO Pin Output Set Register GPIO<31:0> */
#define GPSR1		__REG(0x40E0001C)  /* GPIO Pin Output Set Register GPIO<63:32> */
#define GPSR2		__REG(0x40E00020)  /* GPIO Pin Output Set Register GPIO<80:64> */

#define GPCR0		__REG(0x40E00024)  /* GPIO Pin Output Clear Register GPIO<31:0> */
#define GPCR1		__REG(0x40E00028)  /* GPIO Pin Output Clear Register GPIO <63:32> */
#define GPCR2		__REG(0x40E0002C)  /* GPIO Pin Output Clear Register GPIO <80:64> */

#define GRER0		__REG(0x40E00030)  /* GPIO Rising-Edge Detect Register GPIO<31:0> */
#define GRER1		__REG(0x40E00034)  /* GPIO Rising-Edge Detect Register GPIO<63:32> */
#define GRER2		__REG(0x40E00038)  /* GPIO Rising-Edge Detect Register GPIO<80:64> */

#define GFER0		__REG(0x40E0003C)  /* GPIO Falling-Edge Detect Register GPIO<31:0> */
#define GFER1		__REG(0x40E00040)  /* GPIO Falling-Edge Detect Register GPIO<63:32> */
#define GFER2		__REG(0x40E00044)  /* GPIO Falling-Edge Detect Register GPIO<80:64> */

#define GEDR0		__REG(0x40E00048)  /* GPIO Edge Detect Status Register GPIO<31:0> */
#define GEDR1		__REG(0x40E0004C)  /* GPIO Edge Detect Status Register GPIO<63:32> */
#define GEDR2		__REG(0x40E00050)  /* GPIO Edge Detect Status Register GPIO<80:64> */

#define GAFR0_L		__REG(0x40E00054)  /* GPIO Alternate Function Select Register GPIO<15:0> */
#define GAFR0_U		__REG(0x40E00058)  /* GPIO Alternate Function Select Register GPIO<31:16> */
#define GAFR1_L		__REG(0x40E0005C)  /* GPIO Alternate Function Select Register GPIO<47:32> */
#define GAFR1_U		__REG(0x40E00060)  /* GPIO Alternate Function Select Register GPIO<63:48> */
#define GAFR2_L		__REG(0x40E00064)  /* GPIO Alternate Function Select Register GPIO<79:64> */
#define GAFR2_U		__REG(0x40E00068)  /* GPIO Alternate Function Select Register GPIO<95-80> */
#define GAFR3_L		__REG(0x40E0006C)  /* GPIO Alternate Function Select Register GPIO<111:96> */
#define GAFR3_U		__REG(0x40E00070)  /* GPIO Alternate Function Select Register GPIO<127:112> */

#define GPLR3		__REG(0x40E00100)  /* GPIO Pin-Level Register GPIO<127:96> */
#define GPDR3		__REG(0x40E0010C)  /* GPIO Pin Direction Register GPIO<127:96> */
#define GPSR3		__REG(0x40E00118)  /* GPIO Pin Output Set Register GPIO<127:96> */
#define GPCR3		__REG(0x40E00124)  /* GPIO Pin Output Clear Register GPIO<127:96> */
#define GRER3		__REG(0x40E00130)  /* GPIO Rising-Edge Detect Register GPIO<127:96> */
#define GFER3		__REG(0x40E0013C)  /* GPIO Falling-Edge Detect Register GPIO<127:96> */
#define GEDR3		__REG(0x40E00148)  /* GPIO Edge Detect Status Register GPIO<127:96> */

/* More handy macros.  The argument is a literal GPIO number. */

#define GPIO_bit(x)	(1 << ((x) & 0x1f))

#ifdef CONFIG_PXA27x

/* Interrupt Controller */

#define ICIP2		__REG(0x40D0009C)  /* Interrupt Controller IRQ Pending Register 2 */
#define ICMR2		__REG(0x40D000A0)  /* Interrupt Controller Mask Register 2 */
#define ICLR2		__REG(0x40D000A4)  /* Interrupt Controller Level Register 2 */
#define ICFP2		__REG(0x40D000A8)  /* Interrupt Controller FIQ Pending Register 2 */
#define ICPR2		__REG(0x40D000AC)  /* Interrupt Controller Pending Register 2 */

#define _GPLR(x)	__REG2(0x40E00000, ((x) & 0x60) >> 3)
#define _GPDR(x)	__REG2(0x40E0000C, ((x) & 0x60) >> 3)
#define _GPSR(x)	__REG2(0x40E00018, ((x) & 0x60) >> 3)
#define _GPCR(x)	__REG2(0x40E00024, ((x) & 0x60) >> 3)
#define _GRER(x)	__REG2(0x40E00030, ((x) & 0x60) >> 3)
#define _GFER(x)	__REG2(0x40E0003C, ((x) & 0x60) >> 3)
#define _GEDR(x)	__REG2(0x40E00048, ((x) & 0x60) >> 3)
#define _GAFR(x)	__REG2(0x40E00054, ((x) & 0x70) >> 2)

#define GPLR(x) 	(*((((x) & 0x7f) < 96) ? &_GPLR(x) : &GPLR3))
#define GPDR(x)		(*((((x) & 0x7f) < 96) ? &_GPDR(x) : &GPDR3))
#define GPSR(x)		(*((((x) & 0x7f) < 96) ? &_GPSR(x) : &GPSR3))
#define GPCR(x)		(*((((x) & 0x7f) < 96) ? &_GPCR(x) : &GPCR3))
#define GRER(x)		(*((((x) & 0x7f) < 96) ? &_GRER(x) : &GRER3))
#define GFER(x)		(*((((x) & 0x7f) < 96) ? &_GFER(x) : &GFER3))
#define GEDR(x)		(*((((x) & 0x7f) < 96) ? &_GEDR(x) : &GEDR3))
#define GAFR(x)		(*((((x) & 0x7f) < 96) ? &_GAFR(x) : \
			 ((((x) & 0x7f) < 112) ? &GAFR3_L : &GAFR3_U)))
#else

#define GPLR(x)		__REG2(0x40E00000, ((x) & 0x60) >> 3)
#define GPDR(x)		__REG2(0x40E0000C, ((x) & 0x60) >> 3)
#define GPSR(x)		__REG2(0x40E00018, ((x) & 0x60) >> 3)
#define GPCR(x)		__REG2(0x40E00024, ((x) & 0x60) >> 3)
#define GRER(x)		__REG2(0x40E00030, ((x) & 0x60) >> 3)
#define GFER(x)		__REG2(0x40E0003C, ((x) & 0x60) >> 3)
#define GEDR(x)		__REG2(0x40E00048, ((x) & 0x60) >> 3)
#define G