kconfig

linux-2.6.15.6

#
# wan devices configuration
#

menu "Wan interfaces"
	depends on NETDEVICES

config WAN
	bool "Wan interfaces support"
	---help---
	  Wide Area Networks (WANs), such as X.25, Frame Relay and leased
	  lines, are used to interconnect Local Area Networks (LANs) over vast
	  distances with data transfer rates significantly higher than those
	  achievable with commonly used asynchronous modem connections.

	  Usually, a quite expensive external device called a `WAN router' is
	  needed to connect to a WAN. As an alternative, a relatively
	  inexpensive WAN interface card can allow your Linux box to directly
	  connect to a WAN.

	  If you have one of those cards and wish to use it under Linux,
	  say Y here and also to the WAN driver for your card.

	  If unsure, say N.

# There is no way to detect a comtrol sv11 - force it modular for now.
config HOSTESS_SV11
	tristate "Comtrol Hostess SV-11 support"
	depends on WAN && ISA && m && ISA_DMA_API
	help
	  Driver for Comtrol Hostess SV-11 network card which
	  operates on low speed synchronous serial links at up to
	  256Kbps, supporting PPP and Cisco HDLC.

	  The driver will be compiled as a module: the
	  module will be called hostess_sv11.

# The COSA/SRP driver has not been tested as non-modular yet.
config COSA
	tristate "COSA/SRP sync serial boards support"
	depends on WAN && ISA && m && ISA_DMA_API
	---help---
	  Driver for COSA and SRP synchronous serial boards.

	  These boards allow to connect synchronous serial devices (for example
	  base-band modems, or any other device with the X.21, V.24, V.35 or
	  V.36 interface) to your Linux box. The cards can work as the
	  character device, synchronous PPP network device, or the Cisco HDLC
	  network device.

	  You will need user-space utilities COSA or SRP boards for downloading
 	  the firmware to the cards and to set them up. Look at the
	  <http://www.fi.muni.cz/~kas/cosa/> for more information. You can also
	  read the comment at the top of the <file:drivers/net/wan/cosa.c> for
	  details about the cards and the driver itself.

	  The driver will be compiled as a module: the
	  module will be called cosa.

config DSCC4
	tristate "Etinc PCISYNC serial board support"
	depends on WAN && PCI && m
	help
	  Driver for Etinc PCISYNC boards based on the Infineon (ex. Siemens)
	  DSCC4 chipset.

	  This is supposed to work with the four port card. Take a look at
	  <http://www.cogenit.fr/dscc4/> for further information about the
	  driver.

	  To compile this driver as a module, choose M here: the
	  module will be called dscc4.

config DSCC4_PCISYNC
	bool "Etinc PCISYNC features"
	depends on DSCC4
	help
	  Due to Etinc's design choice for its PCISYNC cards, some operations
	  are only allowed on specific ports of the DSCC4. This option is the
	  only way for the driver to know that it shouldn't return a success
	  code for these operations.

	  Please say Y if your card is an Etinc's PCISYNC.

config DSCC4_PCI_RST
	bool "Hard reset support"
	depends on DSCC4
	help
	  Various DSCC4 bugs forbid any reliable software reset of the ASIC.
	  As a replacement, some vendors provide a way to assert the PCI #RST
	  pin of DSCC4 through the GPIO port of the card. If you choose Y,
	  the driver will make use of this feature before module removal
	  (i.e. rmmod). The feature is known to be available on Commtech's
	  cards. Contact your manufacturer for details.

	  Say Y if your card supports this feature.

#
# Lan Media's board. Currently 1000, 1200, 5200, 5245
#
config LANMEDIA
	tristate "LanMedia Corp. SSI/V.35, T1/E1, HSSI, T3 boards"
	depends on WAN && PCI
	---help---
	  Driver for the following Lan Media family of serial boards:

	  - LMC 1000 board allows you to connect synchronous serial devices
	  (for example base-band modems, or any other device with the X.21,
	  V.24, V.35 or V.36 interface) to your Linux box.

	  - LMC 1200 with on board DSU board allows you to connect your Linux
	  box directly to a T1 or E1 circuit.

	  - LMC 5200 board provides a HSSI interface capable of running up to
	  52 Mbits per second.

	  - LMC 5245 board connects directly to a T3 circuit saving the
	  additional external hardware.

	  To change setting such as syncPPP vs Cisco HDLC or clock source you
	  will need lmcctl.  It is available at <ftp://ftp.lanmedia.com/>
	  (broken link).

	  To compile this driver as a module, choose M here: the
	  module will be called lmc.

# There is no way to detect a Sealevel board. Force it modular
config SEALEVEL_4021
	tristate "Sealevel Systems 4021 support"
	depends on WAN && ISA && m && ISA_DMA_API
	help
	  This is a driver for the Sealevel Systems ACB 56 serial I/O adapter.

	  The driver will be compiled as a module: the
	  module will be called sealevel.

config SYNCLINK_SYNCPPP
	tristate "SyncLink HDLC/SYNCPPP support"
	depends on WAN
	help
	  Enables HDLC/SYNCPPP support for the SyncLink WAN driver.

	  Normally the SyncLink WAN driver works with the main PPP driver
	  <file:drivers/net/ppp_generic.c> and pppd program.
	  HDLC/SYNCPPP support allows use of the Cisco HDLC/PPP driver
	  <file:drivers/net/wan/syncppp.c>. The SyncLink WAN driver (in
	  character devices) must also be enabled.

# Generic HDLC
config HDLC
	tristate "Generic HDLC layer"
	depends on WAN
	help
	  Say Y to this option if your Linux box contains a WAN (Wide Area
	  Network) card supported by this driver and you are planning to
	  connect the box to a WAN.

	  You will need supporting software from
	  <http://www.kernel.org/pub/linux/utils/net/hdlc/>.
	  Generic HDLC driver currently supports raw HDLC, Cisco HDLC, Frame
	  Relay, synchronous Point-to-Point Protocol (PPP) and X.25.

 	  To compile this driver as a module, choose M here: the
	  module will be called hdlc.

	  If unsure, say N.

config HDLC_RAW
	bool "Raw HDLC support"
	depends on HDLC
	help
	  Generic HDLC driver supporting raw HDLC over WAN connections.

	  If unsure, say N.

config HDLC_RAW_ETH
	bool "Raw HDLC Ethernet device support"
	depends on HDLC
	help
	  Generic HDLC driver supporting raw HDLC Ethernet device emulation
	  over WAN connections.

	  You will need it for Ethernet over HDLC bridges.

	  If unsure, say N.

config HDLC_CISCO
	bool "Cisco HDLC support"
	depends on HDLC
	help
	  Generic HDLC driver supporting Cisco HDLC over WAN connections.

	  If unsure, say N.

config HDLC_FR
	bool "Frame Relay support"
	depends on HDLC
	help
	  Generic HDLC driver supporting Frame Relay over WAN connections.

	  If unsure, say N.

config HDLC_PPP
	bool "Synchronous Point-to-Point Protocol (PPP) support"
	depends on HDLC
	help
	  Generic HDLC driver supporting PPP over WAN connections.

	  If unsure, say N.

config HDLC_X25
	bool "X.25 protocol support"
	depends on HDLC && (LAPB=m && HDLC=m || LAPB=y)
	help
	  Generic HDLC driver supporting X.25 over WAN connections.

	  If unsure, say N.

comment "X.25/LAPB support is disabled"
	depends on WAN && HDLC && (LAPB!=m || HDLC!=m) && LAPB!=y

config PCI200SYN
	tristate "Goramo PCI200SYN support"
	depends on HDLC && PCI
	help
	  Driver for PCI200SYN cards by Goramo sp. j.

	  If you have such a card, say Y here and see
	  <http://www.kernel.org/pub/linux/utils/net/hdlc/>.

	  To compile this as a module, choose M here: the
	  module will be called pci200syn.

	  If unsure, say N.

config WANXL
	tristate "SBE Inc. wanXL support"
	depends on HDLC && PCI
	help
	  Driver for wanXL PCI cards by SBE Inc.

	  If you have such a card, say Y here and see
	  <http://www.kernel.org/pub/linux/utils/net/hdlc/>.

	  To compile this as a module, choose M here: the
	  module will be called wanxl.

	  If unsure, say N.

config WANXL_BUILD_FIRMWARE
	bool "rebuild wanXL firmware"
	depends on WANXL && !PREVENT_FIRMWARE_BUILD
	help
	  Allows you to rebuild firmware run by the QUICC processor.
	  It requires as68k, ld68k and hexdump programs.

	  You should never need this option, say N.

config PC300
	tristate "Cyclades-PC300 support (RS-232/V.35, X.21, T1/E1 boards)"
	depends on HDLC && PCI
	---help---
	  Driver for the Cyclades-PC300 synchronous communication boards.

	  These boards provide synchronous serial interfaces to your
	  Linux box (interfaces currently available are RS-232/V.35, X.21 and
	  T1/E1). If you wish to support Multilink PPP, please select the
	  option later and read the file README.mlppp provided by PC300
	  package.

	  To compile this as a module, choose M here: the module
	  will be called pc300.

	  If unsure, say N.

config PC300_MLPPP
	bool "Cyclades-PC300 MLPPP support"
	depends on PC300 && PPP_MULTILINK && PPP_SYNC_TTY && HDLC_PPP
	help
	  Multilink PPP over the PC300 synchronous communication boards.

comment "Cyclades-PC300 MLPPP support is disabled."
	depends on WAN && HDLC && PC300 && (PPP=n || !PPP_MULTILINK || PPP_SYNC_TTY=n || !HDLC_PPP)

comment "Refer to the file README.mlppp, provided by PC300 package."
	depends on WAN && HDLC && PC300 && (PPP=n || !PPP_MULTILINK || PPP_SYNC_TTY=n || !HDLC_PPP)

config N2
	tristate "SDL RISCom/N2 support"
	depends on HDLC && ISA
	help
	  Driver for RISCom/N2 single or dual channel ISA cards by
	  SDL Communications Inc.

	  If you have such a card, say Y here and see
	  <http://www.kernel.org/pub/linux/utils/net/hdlc/>.

	  Note that N2csu and N2dds cards are not supported by this driver.

	  To compile this driver as a module, choose M here: the module
	  will be called n2.

	  If unsure, say N.