exoparg2.c

linux-2.6.15.6

/******************************************************************************
 *
 * Module Name: exoparg2 - AML execution - opcodes with 2 arguments
 *
 *****************************************************************************/

/*
 * Copyright (C) 2000 - 2005, R. Byron Moore
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions, and the following disclaimer,
 *    without modification.
 * 2. Redistributions in binary form must reproduce at minimum a disclaimer
 *    substantially similar to the "NO WARRANTY" disclaimer below
 *    ("Disclaimer") and any redistribution must be conditioned upon
 *    including a substantially similar Disclaimer requirement for further
 *    binary redistribution.
 * 3. Neither the names of the above-listed copyright holders nor the names
 *    of any contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * Alternatively, this software may be distributed under the terms of the
 * GNU General Public License ("GPL") version 2 as published by the Free
 * Software Foundation.
 *
 * NO WARRANTY
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGES.
 */

#include <acpi/acpi.h>
#include <acpi/acparser.h>
#include <acpi/acinterp.h>
#include <acpi/acevents.h>
#include <acpi/amlcode.h>

#define _COMPONENT          ACPI_EXECUTER
ACPI_MODULE_NAME("exoparg2")

/*!
 * Naming convention for AML interpreter execution routines.
 *
 * The routines that begin execution of AML opcodes are named with a common
 * convention based upon the number of arguments, the number of target operands,
 * and whether or not a value is returned:
 *
 *      AcpiExOpcode_xA_yT_zR
 *
 * Where:
 *
 * xA - ARGUMENTS:    The number of arguments (input operands) that are
 *                    required for this opcode type (1 through 6 args).
 * yT - TARGETS:      The number of targets (output operands) that are required
 *                    for this opcode type (0, 1, or 2 targets).
 * zR - RETURN VALUE: Indicates whether this opcode type returns a value
 *                    as the function return (0 or 1).
 *
 * The AcpiExOpcode* functions are called via the Dispatcher component with
 * fully resolved operands.
!*/
/*******************************************************************************
 *
 * FUNCTION:    acpi_ex_opcode_2A_0T_0R
 *
 * PARAMETERS:  walk_state          - Current walk state
 *
 * RETURN:      Status
 *
 * DESCRIPTION: Execute opcode with two arguments, no target, and no return
 *              value.
 *
 * ALLOCATION:  Deletes both operands
 *
 ******************************************************************************/
acpi_status acpi_ex_opcode_2A_0T_0R(struct acpi_walk_state *walk_state)
{
	union acpi_operand_object **operand = &walk_state->operands[0];
	struct acpi_namespace_node *node;
	u32 value;
	acpi_status status = AE_OK;

	ACPI_FUNCTION_TRACE_STR("ex_opcode_2A_0T_0R",
				acpi_ps_get_opcode_name(walk_state->opcode));

	/* Examine the opcode */

	switch (walk_state->opcode) {
	case AML_NOTIFY_OP:	/* Notify (notify_object, notify_value) */

		/* The first operand is a namespace node */

		node = (struct acpi_namespace_node *)operand[0];

		/* Second value is the notify value */

		value = (u32) operand[1]->integer.value;

		/* Are notifies allowed on this object? */

		if (!acpi_ev_is_notify_object(node)) {
			ACPI_DEBUG_PRINT((ACPI_DB_ERROR,
					  "Unexpected notify object type [%s]\n",
					  acpi_ut_get_type_name(node->type)));

			status = AE_AML_OPERAND_TYPE;
			break;
		}
#ifdef ACPI_GPE_NOTIFY_CHECK
		/*
		 * GPE method wake/notify check.  Here, we want to ensure that we
		 * don't receive any "device_wake" Notifies from a GPE _Lxx or _Exx
		 * GPE method during system runtime.  If we do, the GPE is marked
		 * as "wake-only" and disabled.
		 *
		 * 1) Is the Notify() value == device_wake?
		 * 2) Is this a GPE deferred method?  (An _Lxx or _Exx method)
		 * 3) Did the original GPE happen at system runtime?
		 *    (versus during wake)
		 *
		 * If all three cases are true, this is a wake-only GPE that should
		 * be disabled at runtime.
		 */
		if (value == 2) {	/* device_wake */
			status =
			    acpi_ev_check_for_wake_only_gpe(walk_state->
							    gpe_event_info);
			if (ACPI_FAILURE(status)) {
				/* AE_WAKE_ONLY_GPE only error, means ignore this notify */

				return_ACPI_STATUS(AE_OK)
			}
		}
#endif

		/*
		 * Dispatch the notify to the appropriate handler
		 * NOTE: the request is queued for execution after this method
		 * completes.  The notify handlers are NOT invoked synchronously
		 * from this thread -- because handlers may in turn run other
		 * control methods.
		 */
		status = acpi_ev_queue_notify_request(node, value);
		break;

	default:

		ACPI_REPORT_ERROR(("acpi_ex_opcode_2A_0T_0R: Unknown opcode %X\n", walk_state->opcode));
		status = AE_AML_BAD_OPCODE;
	}

	return_ACPI_STATUS(status);
}

/*******************************************************************************
 *
 * FUNCTION:    acpi_ex_opcode_2A_2T_1R
 *
 * PARAMETERS:  walk_state          - Current walk state
 *
 * RETURN:      Status
 *
 * DESCRIPTION: Execute a dyadic operator (2 operands) with 2 output targets
 *              and one implicit return value.
 *
 ******************************************************************************/

acpi_status acpi_ex_opcode_2A_2T_1R(struct acpi_walk_state *walk_state)
{
	union acpi_operand_object **operand = &walk_state->operands[0];
	union acpi_operand_object *return_desc1 = NULL;
	union acpi_operand_object *return_desc2 = NULL;
	acpi_status status;

	ACPI_FUNCTION_TRACE_STR("ex_opcode_2A_2T_1R",
				acpi_ps_get_opcode_name(walk_state->opcode));

	/* Execute the opcode */

	switch (walk_state->opcode) {
	case AML_DIVIDE_OP:

		/* Divide (Dividend, Divisor, remainder_result quotient_result) */

		return_desc1 =
		    acpi_ut_create_internal_object(ACPI_TYPE_INTEGER);
		if (!return_desc1) {
			status = AE_NO_MEMORY;
			goto cleanup;
		}

		return_desc2 =
		    acpi_ut_create_internal_object(ACPI_TYPE_INTEGER);
		if (!return_desc2) {
			status = AE_NO_MEMORY;
			goto cleanup;
		}

		/* Quotient to return_desc1, remainder to return_desc2 */

		status = acpi_ut_divide(operand[0]->integer.value,
					operand[1]->integer.value,
					&return_desc1->integer.value,
					&return_desc2->integer.value);
		if (ACPI_FAILURE(status)) {
			goto cleanup;
		}
		break;

	default:

		ACPI_REPORT_ERROR(("acpi_ex_opcode_2A_2T_1R: Unknown opcode %X\n", walk_state->opcode));
		status = AE_AML_BAD_OPCODE;
		goto cleanup;
	}

	/* Store the results to the target reference operands */

	status = acpi_ex_store(return_desc2, operand[2], walk_state);
	if (ACPI_FAILURE(status)) {
		goto cleanup;
	}

	status = acpi_ex_store(return_desc1, operand[3], walk_state);
	if (ACPI_FAILURE(status)) {
		goto cleanup;
	}

	/* Return the remainder */

	walk_state->result_obj = return_desc1;

      cleanup:
	/*
	 * Since the remainder is not returned indirectly, remove a reference to
	 * it. Only the quotient is returned indirectly.
	 */
	acpi_ut_remove_reference(return_desc2);

	if (ACPI_FAILURE(status)) {
		/* Delete the return object */

		acpi_ut_remove_reference(return_desc1);
	}

	return_ACPI_STATUS(status);
}

/*******************************************************************************
 *
 * FUNCTION:    acpi_ex_opcode_2A_1T_1R
 *
 * PARAMETERS:  walk_state          - Current walk state
 *
 * RETURN:      Status
 *
 * DESCRIPTION: Execute opcode with two arguments, one target, and a return
 *              value.
 *
 ******************************************************************************/

acpi_status acpi_ex_opcode_2A_1T_1R(struct acpi_walk_state *walk_state)
{
	union acpi_operand_object **operand = &walk_state->operands[0];
	union acpi_operand_object *return_desc = NULL;
	acpi_integer index;
	acpi_status status = AE_OK;
	acpi_size length;

	ACPI_FUNCTION_TRACE_STR("ex_opcode_2A_1T_1R",
				acpi_ps_get_opcode_name(walk_state->opcode));

	/* Execute the opcode */

	if (walk_state->op_info->flags & AML_MATH) {
		/* All simple math opcodes (add, etc.) */