📄 ppc85xx_setup.c
字号:
/* * arch/ppc/syslib/ppc85xx_setup.c * * MPC85XX common board code * * Maintainer: Kumar Gala <galak@kernel.crashing.org> * * Copyright 2004 Freescale Semiconductor Inc. * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the * Free Software Foundation; either version 2 of the License, or (at your * option) any later version. */#include <linux/config.h>#include <linux/types.h>#include <linux/module.h>#include <linux/init.h>#include <linux/pci.h>#include <linux/serial.h>#include <linux/tty.h> /* for linux/serial_core.h */#include <linux/serial_core.h>#include <linux/serial_8250.h>#include <asm/time.h>#include <asm/mpc85xx.h>#include <asm/immap_85xx.h>#include <asm/mmu.h>#include <asm/ppc_sys.h>#include <asm/kgdb.h>#include <asm/machdep.h>#include <syslib/ppc85xx_setup.h>extern void abort(void);/* Return the amount of memory */unsigned long __initmpc85xx_find_end_of_memory(void){ bd_t *binfo; binfo = (bd_t *) __res; return binfo->bi_memsize;}/* The decrementer counts at the system (internal) clock freq divided by 8 */void __initmpc85xx_calibrate_decr(void){ bd_t *binfo = (bd_t *) __res; unsigned int freq, divisor; /* get the core frequency */ freq = binfo->bi_busfreq; /* The timebase is updated every 8 bus clocks, HID0[SEL_TBCLK] = 0 */ divisor = 8; tb_ticks_per_jiffy = freq / divisor / HZ; tb_to_us = mulhwu_scale_factor(freq / divisor, 1000000); /* Set the time base to zero */ mtspr(SPRN_TBWL, 0); mtspr(SPRN_TBWU, 0); /* Clear any pending timer interrupts */ mtspr(SPRN_TSR, TSR_ENW | TSR_WIS | TSR_DIS | TSR_FIS); /* Enable decrementer interrupt */ mtspr(SPRN_TCR, TCR_DIE);}#ifdef CONFIG_SERIAL_8250void __initmpc85xx_early_serial_map(void){#if defined(CONFIG_SERIAL_TEXT_DEBUG) || defined(CONFIG_KGDB) struct uart_port serial_req;#endif struct plat_serial8250_port *pdata; bd_t *binfo = (bd_t *) __res; pdata = (struct plat_serial8250_port *) ppc_sys_get_pdata(MPC85xx_DUART); /* Setup serial port access */ pdata[0].uartclk = binfo->bi_busfreq; pdata[0].mapbase += binfo->bi_immr_base; pdata[0].membase = ioremap(pdata[0].mapbase, MPC85xx_UART0_SIZE);#if defined(CONFIG_SERIAL_TEXT_DEBUG) || defined(CONFIG_KGDB) memset(&serial_req, 0, sizeof (serial_req)); serial_req.iotype = SERIAL_IO_MEM; serial_req.mapbase = pdata[0].mapbase; serial_req.membase = pdata[0].membase; serial_req.regshift = 0; gen550_init(0, &serial_req);#endif pdata[1].uartclk = binfo->bi_busfreq; pdata[1].mapbase += binfo->bi_immr_base; pdata[1].membase = ioremap(pdata[1].mapbase, MPC85xx_UART0_SIZE);#if defined(CONFIG_SERIAL_TEXT_DEBUG) || defined(CONFIG_KGDB) /* Assume gen550_init() doesn't modify serial_req */ serial_req.mapbase = pdata[1].mapbase; serial_req.membase = pdata[1].membase; gen550_init(1, &serial_req);#endif}#endifvoidmpc85xx_restart(char *cmd){ local_irq_disable(); abort();}voidmpc85xx_power_off(void){ local_irq_disable(); for(;;);}voidmpc85xx_halt(void){ local_irq_disable(); for(;;);}#ifdef CONFIG_PCI#if defined(CONFIG_MPC8555_CDS) || defined(CONFIG_MPC8548_CDS)extern void mpc85xx_cds_enable_via(struct pci_controller *hose);extern void mpc85xx_cds_fixup_via(struct pci_controller *hose);#endifstatic void __initmpc85xx_setup_pci1(struct pci_controller *hose){ volatile struct ccsr_pci *pci; volatile struct ccsr_guts *guts; unsigned short temps; bd_t *binfo = (bd_t *) __res; pci = ioremap(binfo->bi_immr_base + MPC85xx_PCI1_OFFSET, MPC85xx_PCI1_SIZE); guts = ioremap(binfo->bi_immr_base + MPC85xx_GUTS_OFFSET, MPC85xx_GUTS_SIZE); early_read_config_word(hose, 0, 0, PCI_COMMAND, &temps); temps |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY; early_write_config_word(hose, 0, 0, PCI_COMMAND, temps);#define PORDEVSR_PCI (0x00800000) /* PCI Mode */ if (guts->pordevsr & PORDEVSR_PCI) { early_write_config_byte(hose, 0, 0, PCI_LATENCY_TIMER, 0x80); } else { /* PCI-X init */ temps = PCI_X_CMD_MAX_SPLIT | PCI_X_CMD_MAX_READ | PCI_X_CMD_ERO | PCI_X_CMD_DPERR_E; early_write_config_word(hose, 0, 0, PCIX_COMMAND, temps); } /* Disable all windows (except powar0 since its ignored) */ pci->powar1 = 0; pci->powar2 = 0; pci->powar3 = 0; pci->powar4 = 0; pci->piwar1 = 0; pci->piwar2 = 0; pci->piwar3 = 0; /* Setup Phys:PCI 1:1 outbound mem window @ MPC85XX_PCI1_LOWER_MEM */ pci->potar1 = (MPC85XX_PCI1_LOWER_MEM >> 12) & 0x000fffff; pci->potear1 = 0x00000000; pci->powbar1 = (MPC85XX_PCI1_LOWER_MEM >> 12) & 0x000fffff; /* Enable, Mem R/W */ pci->powar1 = 0x80044000 | (__ilog2(MPC85XX_PCI1_UPPER_MEM - MPC85XX_PCI1_LOWER_MEM + 1) - 1); /* Setup outbound IO windows @ MPC85XX_PCI1_IO_BASE */ pci->potar2 = (MPC85XX_PCI1_LOWER_IO >> 12) & 0x000fffff; pci->potear2 = 0x00000000; pci->powbar2 = (MPC85XX_PCI1_IO_BASE >> 12) & 0x000fffff; /* Enable, IO R/W */ pci->powar2 = 0x80088000 | (__ilog2(MPC85XX_PCI1_IO_SIZE) - 1); /* Setup 2G inbound Memory Window @ 0 */ pci->pitar1 = 0x00000000; pci->piwbar1 = 0x00000000; pci->piwar1 = 0xa0f5501e; /* Enable, Prefetch, Local Mem, Snoop R/W, 2G */}extern int mpc85xx_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin);extern int mpc85xx_exclude_device(u_char bus, u_char devfn);#ifdef CONFIG_85xx_PCI2static void __initmpc85xx_setup_pci2(struct pci_controller *hose){ volatile struct ccsr_pci *pci; unsigned short temps; bd_t *binfo = (bd_t *) __res; pci = ioremap(binfo->bi_immr_base + MPC85xx_PCI2_OFFSET, MPC85xx_PCI2_SIZE); early_read_config_word(hose, hose->bus_offset, 0, PCI_COMMAND, &temps); temps |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY; early_write_config_word(hose, hose->bus_offset, 0, PCI_COMMAND, temps); early_write_config_byte(hose, hose->bus_offset, 0, PCI_LATENCY_TIMER, 0x80); /* Disable all windows (except powar0 since its ignored) */ pci->powar1 = 0; pci->powar2 = 0; pci->powar3 = 0; pci->powar4 = 0; pci->piwar1 = 0; pci->piwar2 = 0; pci->piwar3 = 0; /* Setup Phys:PCI 1:1 outbound mem window @ MPC85XX_PCI2_LOWER_MEM */ pci->potar1 = (MPC85XX_PCI2_LOWER_MEM >> 12) & 0x000fffff; pci->potear1 = 0x00000000; pci->powbar1 = (MPC85XX_PCI2_LOWER_MEM >> 12) & 0x000fffff; /* Enable, Mem R/W */ pci->powar1 = 0x80044000 | (__ilog2(MPC85XX_PCI2_UPPER_MEM - MPC85XX_PCI2_LOWER_MEM + 1) - 1); /* Setup outbound IO windows @ MPC85XX_PCI2_IO_BASE */ pci->potar2 = (MPC85XX_PCI2_LOWER_IO >> 12) & 0x000fffff;; pci->potear2 = 0x00000000; pci->powbar2 = (MPC85XX_PCI2_IO_BASE >> 12) & 0x000fffff; /* Enable, IO R/W */ pci->powar2 = 0x80088000 | (__ilog2(MPC85XX_PCI2_IO_SIZE) - 1); /* Setup 2G inbound Memory Window @ 0 */ pci->pitar1 = 0x00000000; pci->piwbar1 = 0x00000000; pci->piwar1 = 0xa0f5501e; /* Enable, Prefetch, Local Mem, Snoop R/W, 2G */}#endif /* CONFIG_85xx_PCI2 */int mpc85xx_pci1_last_busno = 0;void __initmpc85xx_setup_hose(void){ struct pci_controller *hose_a;#ifdef CONFIG_85xx_PCI2 struct pci_controller *hose_b;#endif bd_t *binfo = (bd_t *) __res; hose_a = pcibios_alloc_controller(); if (!hose_a) return; ppc_md.pci_swizzle = common_swizzle; ppc_md.pci_map_irq = mpc85xx_map_irq; hose_a->first_busno = 0; hose_a->bus_offset = 0; hose_a->last_busno = 0xff; setup_indirect_pci(hose_a, binfo->bi_immr_base + PCI1_CFG_ADDR_OFFSET, binfo->bi_immr_base + PCI1_CFG_DATA_OFFSET); hose_a->set_cfg_type = 1; mpc85xx_setup_pci1(hose_a); hose_a->pci_mem_offset = MPC85XX_PCI1_MEM_OFFSET; hose_a->mem_space.start = MPC85XX_PCI1_LOWER_MEM; hose_a->mem_space.end = MPC85XX_PCI1_UPPER_MEM; hose_a->io_space.start = MPC85XX_PCI1_LOWER_IO; hose_a->io_space.end = MPC85XX_PCI1_UPPER_IO; hose_a->io_base_phys = MPC85XX_PCI1_IO_BASE;#ifdef CONFIG_85xx_PCI2 hose_a->io_base_virt = ioremap(MPC85XX_PCI1_IO_BASE, MPC85XX_PCI1_IO_SIZE + MPC85XX_PCI2_IO_SIZE);#else hose_a->io_base_virt = ioremap(MPC85XX_PCI1_IO_BASE, MPC85XX_PCI1_IO_SIZE);#endif isa_io_base = (unsigned long)hose_a->io_base_virt; /* setup resources */ pci_init_resource(&hose_a->mem_resources[0], MPC85XX_PCI1_LOWER_MEM, MPC85XX_PCI1_UPPER_MEM, IORESOURCE_MEM, "PCI1 host bridge"); pci_init_resource(&hose_a->io_resource, MPC85XX_PCI1_LOWER_IO, MPC85XX_PCI1_UPPER_IO, IORESOURCE_IO, "PCI1 host bridge"); ppc_md.pci_exclude_device = mpc85xx_exclude_device;#if defined(CONFIG_MPC8555_CDS) || defined(CONFIG_MPC8548_CDS) /* Pre pciauto_bus_scan VIA init */ mpc85xx_cds_enable_via(hose_a);#endif hose_a->last_busno = pciauto_bus_scan(hose_a, hose_a->first_busno);#if defined(CONFIG_MPC8555_CDS) || defined(CONFIG_MPC8548_CDS) /* Post pciauto_bus_scan VIA fixup */ mpc85xx_cds_fixup_via(hose_a);#endif#ifdef CONFIG_85xx_PCI2 hose_b = pcibios_alloc_controller(); if (!hose_b) return; hose_b->bus_offset = hose_a->last_busno + 1; hose_b->first_busno = hose_a->last_busno + 1; hose_b->last_busno = 0xff; setup_indirect_pci(hose_b, binfo->bi_immr_base + PCI2_CFG_ADDR_OFFSET, binfo->bi_immr_base + PCI2_CFG_DATA_OFFSET); hose_b->set_cfg_type = 1; mpc85xx_setup_pci2(hose_b); hose_b->pci_mem_offset = MPC85XX_PCI2_MEM_OFFSET; hose_b->mem_space.start = MPC85XX_PCI2_LOWER_MEM; hose_b->mem_space.end = MPC85XX_PCI2_UPPER_MEM; hose_b->io_space.start = MPC85XX_PCI2_LOWER_IO; hose_b->io_space.end = MPC85XX_PCI2_UPPER_IO; hose_b->io_base_phys = MPC85XX_PCI2_IO_BASE; hose_b->io_base_virt = hose_a->io_base_virt + MPC85XX_PCI1_IO_SIZE; /* setup resources */ pci_init_resource(&hose_b->mem_resources[0], MPC85XX_PCI2_LOWER_MEM, MPC85XX_PCI2_UPPER_MEM, IORESOURCE_MEM, "PCI2 host bridge"); pci_init_resource(&hose_b->io_resource, MPC85XX_PCI2_LOWER_IO, MPC85XX_PCI2_UPPER_IO, IORESOURCE_IO, "PCI2 host bridge"); hose_b->last_busno = pciauto_bus_scan(hose_b, hose_b->first_busno); /* let board code know what the last bus number was on PCI1 */ mpc85xx_pci1_last_busno = hose_a->last_busno;#endif return;}#endif /* CONFIG_PCI */
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -