platform.asm

640J3的Flash的驱动和测试程序

    .global platformsetup
    
*
*0X0286        1          2     7       9
OMAP1510_CLKS:  .word 	0x0286	;((1<<EN_XORPCK)|(1<<EN_PERCK)|(1<<EN_TIMCK)|(1<<EN_GPIOCK))
*_TEXT_BASE:
*    .word  0x11080000
*
*
    
platformsetup:

    
*
* Configure 1510 pins functions to match our board.
*
*
* *(0xfffe1040) = 0x11a10000 激活MCBSP1.DR的下拉位,屏蔽CAM的下拉位
*
    ldr     r0, REG_PULL_DWN_CTRL_0
    ldr     r1, VAL_PULL_DWN_CTRL_0
    str     r1, [r0]
*
* *(0xfffe1044) = 0x2e047fff 使MCBSP3.CLKX MPU_BOOT EMU1 EMU0 UWIRE.SDI MPUIO2 MPUIO4
* MPUIO5 GPIO0-GPIO4 GPIO6 GPIO7 GPIO11-GPIO16 下拉无效
*
    ldr     r0, REG_PULL_DWN_CTRL_1
    ldr     r1, VAL_PULL_DWN_CTRL_1
    str     r1, [r0]
*
* *(0xfffe1048) = 0xffd603a6  使MCBSP2(.DX .FSR .CLKX .CLKR .FSX .DR) MPUIO3 GPIO.8 GPIO.9 UART2.CLKREQ
*  MCSI2(.SYNC .DIN .CLK) MCSI1(.DIN .CLK .SYNC) UART3.CLKREQ UART1.RX UART1.CTS下拉无效
*  使MMC.DAT0 .CMD_SPI.DO .DAT1 .DAT2下拉有效
*
    ldr     r0, REG_PULL_DWN_CTRL_2
    ldr     r1, VAL_PULL_DWN_CTRL_2
    str     r1, [r0]
*
* *(0xfffe104c) = 0x00003e03  使/TRST TCK TMS TDI CONF UART2.CTS UART2.RX下拉无效
* 使MMC.DAT3 下拉有效
*
    ldr     r0, REG_PULL_DWN_CTRL_3
    ldr     r1, VAL_PULL_DWN_CTRL_3
    str     r1, [r0]
*
**(0xfffe1014) = 0 默认为CAM与MCBSP1
*
*
    ldr     r0, REG_FUNC_MUX_CTRL_4
    ldr     r1, VAL_FUNC_MUX_CTRL_4
    str     r1, [r0]
*
* *(0xfffe1018) = 0 默认为CAM
*
    ldr     r0, REG_FUNC_MUX_CTRL_5
    ldr     r1, VAL_FUNC_MUX_CTRL_5
    str     r1, [r0]
*
* *(0xfffe101c)=1 或 0 效果一样 默认为GPIO UART3
* * The following phase make the PWT work!!!!!----add by Wzhaohui
*
    ldr     r0, REG_FUNC_MUX_CTRL_6
    ldr     r1, VAL_FUNC_MUX_CTRL_6
    str     r1, [r0]                     
*
**(0xfffe1020)= 0 默认为MPUIO 和GPIO
*
    ldr     r0, REG_FUNC_MUX_CTRL_7
    ldr     r1, VAL_FUNC_MUX_CTRL_7
    str     r1, [r0]
*
**(0xfffe1024)= 0x10001200  第29-27 001 MCBSP3.DR 针对我们的开发板应为000 MPU_BOOT
* 默认下是UWIRE 的控制口,该复用主要是UWIRE UART3 UART1 MCBSP3的复用,针对我们的开发要改动
*
    ldr     r0, REG_FUNC_MUX_CTRL_8
    ldr     r1, VAL_FUNC_MUX_CTRL_8
    str     r1, [r0]
*
* *(0xfffe1028) = 0x01201012 设置异步串口1,与USB1 要改动
*
    ldr     r0, REG_FUNC_MUX_CTRL_9
    ldr     r1, VAL_FUNC_MUX_CTRL_9
    str     r1, [r0]
*
**(0xfffe102C) = 0x00000248
*
    ldr     r0, REG_FUNC_MUX_CTRL_A
    ldr     r1, VAL_FUNC_MUX_CTRL_A
    str     r1, [r0]
    ldr     r0, REG_FUNC_MUX_CTRL_B
    ldr     r1, VAL_FUNC_MUX_CTRL_B
    str     r1, [r0]
    ldr     r0, REG_FUNC_MUX_CTRL_C
    ldr     r1, VAL_FUNC_MUX_CTRL_C
    str     r1, [r0]
    ldr     r0, REG_FUNC_MUX_CTRL_D
    ldr     r1, VAL_FUNC_MUX_CTRL_D
    str     r1, [r0]
*
**()=7
*
    ldr     r0, REG_VOLTAGE_CTRL_0
    ldr     r1, VAL_VOLTAGE_CTRL_0
    str     r1, [r0]
*
* *(0xfffe1070)= 7
*
    ldr     r0, REG_TEST_DBG_CTRL_0
    ldr     r1, VAL_TEST_DBG_CTRL_0
    str     r1, [r0]
    ldr     r0, REG_MOD_CONF_CTRL_0
    ldr     r1, VAL_MOD_CONF_CTRL_0
    str     r1, [r0]

* Move to 1510 mode 激活以上寄存器配置*
    ldr     r0, REG_COMP_MODE_CTRL_0
    ldr     r1, VAL_COMP_MODE_CTRL_0
    str     r1, [r0]

* Set up Traffic Ctlr*
    ldr r0, REG_TC_IMIF_PRIO
    mov r1, #0x0
    str r1, [r0]
    ldr r0, REG_TC_EMIFS_PRIO
    str r1, [r0]
    ldr r0, REG_TC_EMIFF_PRIO
    str r1, [r0]

    ldr r0, REG_TC_EMIFS_CONFIG
    ldr r1, [r0]
    bic r1, r1, #0x08       ; clear the global power-down enable PDE bit
    bic r1, r1, #0x01       ; write protect flash by clearing the WP bit
    str r1, [r0]            ; EMIFS GlB Configuration. (value 0x12 most likely)
    
    
    
* Setup some clock domains  可改*
    ldr r1, OMAP1510_CLKS
    ;MOV r1, #OMAP1510_CLKS
    ldr r0, REG_ARM_IDLECT2
    strh r1, [r0]           ; CLKM, Clock domain control.

    mov r1, #0x01           ; PER_EN bit
    ldr r0, REG_ARM_RSTCT2
    strh r1, [r0]           ; CLKM; Peripheral reset.

* Set CLKM to Sync-Scalable *
* I supposidly need to enable the dsp clock before switching
    mov r1, #0x1000
    ldr r0, REG_ARM_SYSST
    strh r1, [r0]
    mov r0, #0x400
L1:
    subs r0, r0, #0x1       ; wait for any bubbles to finish
    bne L1

    ldr r1, VAL_ARM_CKCTL   ; use 12Mhz ref, PER must be <= 50Mhz so /2  0x010f 改成 0x0506
    ldr r0, REG_ARM_CKCTL
    strh r1, [r0]

* setup DPLL 1 设置时钟*
    ldr r1, VAL_DPLL1_CTL   ;(0xfffecf00) = 0x2cb0为150Mhz
    ldr r0, REG_DPLL1_CTL
    str r1, [r0]
    ands r1, r1, #0x10      ; Check if PLL is enabled.
    beq lock_end            ; Do not look for lock if BYPASS selected
L2:
    ldrh r1, [r0]
    ands r1, r1, #0x01      ; Check the LOCK bit.
    beq L2                  ; ...loop until bit goes hi.
lock_end:
    
* Set memory timings corresponding to the new clock speed*

* Check execution location to determine current execution location
* and branch to appropriate initialization code.
*
    mov r0, #0x10000000            ; Load physical SDRAM base.
    mov r1, pc                     ; Get current execution location.
    cmp r1, r0                     ; Compare.
    bge skip_sdram                 ; 带符号数大于等于Skip over EMIF-fast initialization if running from SDRAM.

*
* Delay for SDRAM initialization. 等待一会，防止SDRAM没有启动
*
    mov r3, #0x1800                 ;value should be checked
L3:
    subs r3, r3, #0x1               ;Decrement count
    bne L3

*
* Set SDRAM control values. Disable refresh before MRS command.
*
    ldr r0, VAL_TC_EMIFF_SDRAM_CONFIG       ; get good value 0x010290fc 该值要改
    bic r3, r0, #0xC                        ; (BIT3|BIT2) ulConfig with auto-refresh disabled.
    orr r3, r3, #0x8000000                  ; (BIT27) Disable CLK when Power down or Self-Refresh
    orr r3, r3, #0x4000000                  ; BIT26 Power Down Enable
    ldr r2, REG_TC_EMIFF_SDRAM_CONFIG       ; 0xfffecc20 Point to configuration register.
    str r3, [r2]                            ; Store the passed value with AR disabled.

    ldr r1, VAL_TC_EMIFF_MRS       ; get MRS value 0x00000027
    ldr r2, REG_TC_EMIFF_MRS       ; Point to MRS register.
    str r1, [r2]                   ; Store the passed value.

    ldr r2, REG_TC_EMIFF_SDRAM_CONFIG   ; 0xfffecc20 Point to configuration register.
    str r0, [r2]                        ; Store the passed value.

*
* Delay for SDRAM initialization.
*
    mov r3, #0x1800
L4:
    subs r3, r3, #1                     ; Decrement count.
    bne L4

skip_sdram:

* slow interface*
    ldr r1, VAL_TC_EMIFS_CS0_CONFIG     ; 0x002130b0 
    ldr r0, REG_TC_EMIFS_CS0_CONFIG     ; 0xfffecc10
    str r1, [r0]                        ; Chip Select 0
    ldr r1, VAL_TC_EMIFS_CS1_CONFIG     ; 0x0000f559 改成0x0000f551
    ldr r0, REG_TC_EMIFS_CS1_CONFIG
    str r1, [r0]                        ; Chip Select 1
    ldr r1, VAL_TC_EMIFS_CS2_CONFIG     ; 0x000055f0 
    ldr r0, REG_TC_EMIFS_CS2_CONFIG
    str r1, [r0]                        ; Chip Select 2
    ldr r1, VAL_TC_EMIFS_CS3_CONFIG     ; 0x00003331
    ldr r0, REG_TC_EMIFS_CS3_CONFIG
    str r1, [r0]                        ; Chip Select 3

* Next, Enable the RS232 Line Drivers in the FPGA.*
* Also, power on the audio CODEC's amplifier here,*
* which will make a noise on the audio output.*
* This is done here instead of in the kernel so there*
* isn't a loud popping noise at the start of each*
* song.*
* Also, disable the CODEC's clocks.*
* omap1510-HelenP1 [specific]*

    ldr r0, REG_FPGA_POWER              ;    0x08000005  
    mov r1, #0
    ldr r2, REG_FPGA_DIP_SWITCH         ;    0x0800000e  
    ldrb r3, [r2]
    cmp r3, #0x8
    movne r1, #0x62                     ; Enable the RS232 Line Drivers in the EPLD
    strb r1, [r0]
    ldr r0, REG_FPGA_AUDIO
    mov r1, #0x0                        ; Disable sound driver (CODEC clocks)
    strb r1, [r0]

    
* back to arch calling code*
    mov pc, lr

* the literal pools origin*
*    .ltorg

* OMAP configuration registers*
REG_FUNC_MUX_CTRL_0:        ; 32 bits
    .word 0xfffe1000
REG_FUNC_MUX_CTRL_1:        ;32 bits
    .word 0xfffe1004
REG_FUNC_MUX_CTRL_2:        ;32 bits
    .word 0xfffe1008
REG_COMP_MODE_CTRL_0:       ;32 bits
    .word 0xfffe100c
REG_FUNC_MUX_CTRL_3:        ;32 bits
    .word 0xfffe1010
REG_FUNC_MUX_CTRL_4:        ;32 bits
    .word 0xfffe1014
REG_FUNC_MUX_CTRL_5:        ;32 bits
    .word 0xfffe1018
REG_FUNC_MUX_CTRL_6:        ;32 bits
    .word 0xfffe101c
REG_FUNC_MUX_CTRL_7:        ;32 bits
    .word 0xfffe1020
REG_FUNC_MUX_CTRL_8:        ;32 bits
    .word 0xfffe1024
REG_FUNC_MUX_CTRL_9:        ;32 bits
    .word 0xfffe1028
REG_FUNC_MUX_CTRL_A:        ;32 bits
    .word 0xfffe102C
REG_FUNC_MUX_CTRL_B:        ;32 bits
    .word 0xfffe1030
REG_FUNC_MUX_CTRL_C:        ;32 bits
    .word 0xfffe1034
REG_FUNC_MUX_CTRL_D:        ;32 bits
    .word 0xfffe1038
REG_PULL_DWN_CTRL_0:        ;32 bits
    .word 0xfffe1040
REG_PULL_DWN_CTRL_1:        ;32 bits
    .word 0xfffe1044
REG_PULL_DWN_CTRL_2:        ;32 bits
    .word 0xfffe1048
REG_PULL_DWN_CTRL_3:        ;32 bits
    .word 0xfffe104c
REG_VOLTAGE_CTRL_0:         ;32 bits
    .word 0xfffe1060
REG_TEST_DBG_CTRL_0:        ;32 bits
    .word 0xfffe1070
REG_MOD_CONF_CTRL_0:        ;32 bits
    .word 0xfffe1080
REG_TC_IMIF_PRIO:           ;32 bits
    .word 0xfffecc00
REG_TC_EMIFS_PRIO:          ;32 bits
    .word 0xfffecc04
REG_TC_EMIFF_PRIO:          ;32 bits
    .word 0xfffecc08
REG_TC_EMIFS_CONFIG:        ;32 bits
    .word 0xfffecc0c
REG_TC_EMIFS_CS0_CONFIG:    ;32 bits
    .word 0xfffecc10
REG_TC_EMIFS_CS1_CONFIG:    ;32 bits
    .word 0xfffecc14
REG_TC_EMIFS_CS2_CONFIG:    ;32 bits
    .word 0xfffecc18
REG_TC_EMIFS_CS3_CONFIG:    ;32 bits
    .word 0xfffecc1c
REG_TC_EMIFF_SDRAM_CONFIG:  ;32 bits
    .word 0xfffecc20
REG_TC_EMIFF_MRS:           ;32 bits
    .word 0xfffecc24
* MPU clock/reset/power mode control registers*
REG_ARM_CKCTL:             ;16 bits
    .word 0xfffece00
REG_ARM_IDLECT2:           ;16 bits
    .word 0xfffece08
REG_ARM_RSTCT2:            ;16 bits
    .word 0xfffece14
REG_ARM_SYSST:             ;16 bits
    .word 0xfffece18
* DPLL control registers*
REG_DPLL1_CTL:             ;16 bits
    .word 0xfffecf00
* identification code register*
REG_IDCODE:                 ;32 bits
    .word 0xfffed404

* Innovator specific*
REG_FPGA_LED_DIGIT:        ;8 bits (not used on Innovator)
    .word 0x08000003
REG_FPGA_POWER:            ;8 bits
    .word 0x08000005
REG_FPGA_AUDIO:            ;8 bits (not used on Innovator)
    .word 0x0800000c
REG_FPGA_DIP_SWITCH:       ;8 bits (not used on Innovator)
    .word 0x0800000e

VAL_COMP_MODE_CTRL_0:
    .word 0x0000eaef
VAL_FUNC_MUX_CTRL_4:
    .word 0x00000000
VAL_FUNC_MUX_CTRL_5:
    .word 0x00000000
    
VAL_FUNC_MUX_CTRL_6:        ;The reason why PWT always work!!!!
    .word 0x00000000        ;Modifed by Wzhaohui   before: 0x00000001
    
VAL_FUNC_MUX_CTRL_7:
    .word 0x00000000
VAL_FUNC_MUX_CTRL_8:
    .word 0x10001200
VAL_FUNC_MUX_CTRL_9:
    .word 0x01201012
VAL_FUNC_MUX_CTRL_A:
    .word 0x00000248
VAL_FUNC_MUX_CTRL_B:
    .word 0x00000248
VAL_FUNC_MUX_CTRL_C:
    .word 0x09000000
VAL_FUNC_MUX_CTRL_D:
    .word 0x00000000
VAL_PULL_DWN_CTRL_0:
    .word 0x11a10000
VAL_PULL_DWN_CTRL_1:
    .word 0x2e047fff
VAL_PULL_DWN_CTRL_2:
    .word 0xffd603a6
VAL_PULL_DWN_CTRL_3:
    .word 0x00003e03
VAL_VOLTAGE_CTRL_0:
    .word 0x00000007
VAL_TEST_DBG_CTRL_0:
*  See Errata 4.13, This works around a SRAM bug, for chips below ES2.5 .
*   This slows down internal SRAM accesses.
*
    .word 0x00000007
VAL_MOD_CONF_CTRL_0:
    .word 0x0b000008
VAL_ARM_CKCTL:
    .word 0x0506        ;0x010f 蒋光明改成0x0506(或0x3506)
VAL_DPLL1_CTL:
    .word 0x2cb0        ;(0xfffecf00) = 0x2710 为168Mhz   0x2cb0为150Mhz
VAL_TC_EMIFS_CS1_CONFIG_PRELIM:
    .word 0x00001149
VAL_TC_EMIFS_CS2_CONFIG_PRELIM:
    .word 0x00004158
VAL_TC_EMIFS_CS0_CONFIG:
    .word 0x000130b0    ;0x002130b0
VAL_TC_EMIFS_CS1_CONFIG:
    .word 0x0000f551
VAL_TC_EMIFS_CS2_CONFIG:
    .word 0x000055f0
VAL_TC_EMIFS_CS3_CONFIG:
    .word 0x00003331
VAL_TC_EMIFF_SDRAM_CONFIG:
    .word 0x010290fc
VAL_TC_EMIFF_MRS:
    .word 0x00000027