tm-a29k.h

lwip在ucos上的移植

   loc2: . . .
   foo:  sub gr1,gr1,rsize_f
   . . .
   add mfp,msp,0
   sub msp,msp,msize_f
   . . .
   loc3: < suppose the inferior stops here >

   memory stack      register stack
   |           |     |____________|
   |           |     |____loc1____|
   +------->|___________|     |            |   ^
   |        | ^         |     |  locals_b  |   |
   |        | |         |     |____________|   |
   |        | |         |     |            |   | rsize_b
   |        | | msize_b |     | args_to_f  |   |
   |        | |         |     |____________|   |
   |        | |         |     |____lr1_____|   V
   |        | V         |     |____loc2____|<----------------+
   |   +--->|___________|<---------mfp     |   ^             |
   |   |    | ^         |     |  locals_f  |   |             |
   |   |    | | msize_f |     |____________|   |             |
   |   |    | |         |     |            |   | rsize_f     |
   |   |    | V         |     |   args     |   |             |
   |   |    |___________|<msp |____________|   |             |
   |   |                      |_____lr1____|   V             |
   |   |                      |___garbage__| <- gr1 <----+   |
   |   |                                                |   |
   |   |                                                |   |
   |   |                             pc=loc3                    |   |
   |   |                                                |   |
   |   |                                                |   |
   |   |            frame cache                         |   |
   |   |       |_________________|                      |   |
   |   |       |rsize=rsize_b    |                      |   |
   |   |       |msize=msize_b    |                      |   |
   +---|--------saved_msp        |                      |   |
   |       |frame------------------------------------|---+
   |       |pc=loc2          |                       |
   |       |_________________|                       |
   |       |rsize=rsize_f    |                       |
   |       |msize=msize_f    |                       |
   +--------saved_msp        |                       |
   |frame------------------------------------+
   |pc=loc3          |
   |_________________|

   So, is that sufficiently confusing?  Welcome to the 29000.
   Notes:
   * The frame for foo uses a memory frame pointer but the frame for
   bar does not.  In the latter case the saved_msp is
   computed by adding msize to the saved_msp of the
   next frame.
   * msize is in the frame cache only for high C's sake.  */
/* *INDENT-ON* */


void read_register_stack ();
long read_register_stack_integer ();

#define FRAME_INIT_SAVED_REGS(fi)	/*no-op */

#define EXTRA_FRAME_INFO  \
  CORE_ADDR saved_msp;    \
  unsigned int rsize;     \
  unsigned int msize;	  \
  unsigned char flags;

/* Bits for flags in EXTRA_FRAME_INFO */
#define TRANSPARENT_FRAME	0x1	/* This is a transparent frame */
#define MFP_USED		0x2	/* A memory frame pointer is used */

/* Because INIT_FRAME_PC gets passed fromleaf, that's where we init
   not only ->pc and ->frame, but all the extra stuff, when called from
   get_prev_frame, that is.  */
#define INIT_EXTRA_FRAME_INFO(fromleaf, fci)  init_extra_frame_info(fci)
void init_extra_frame_info ();

#define INIT_FRAME_PC(fromleaf, fci) init_frame_pc(fromleaf, fci)
void init_frame_pc ();


/* FRAME_CHAIN takes a FRAME
   and produces the frame's chain-pointer.

   However, if FRAME_CHAIN_VALID returns zero,
   it means the given frame is the outermost one and has no caller.  */

/* On the a29k, the nominal address of a frame is the address on the
   register stack of the return address (the one next to the incoming
   arguments, not down at the bottom so nominal address == stack pointer).

   GDB expects "nominal address" to equal contents of FP_REGNUM,
   at least when it comes time to create the innermost frame.
   However, that doesn't work for us, so when creating the innermost
   frame we set ->frame ourselves in INIT_EXTRA_FRAME_INFO.  */

/* These are mostly dummies for the a29k because INIT_FRAME_PC
   sets prev->frame instead.  */
/* If rsize is zero, we must be at end of stack (or otherwise hosed).
   If we don't check rsize, we loop forever if we see rsize == 0.  */
#define FRAME_CHAIN(thisframe) \
  ((thisframe)->rsize == 0 \
   ? 0 \
   : (thisframe)->frame + (thisframe)->rsize)

/* Determine if the frame has a 'previous' and back-traceable frame. */
#define FRAME_IS_UNCHAINED(frame)	((frame)->flags & TRANSPARENT_FRAME)

/* Find the previous frame of a transparent routine.
 * For now lets not try and trace through a transparent routine (we might 
 * have to assume that all transparent routines are traps).
 */
#define FIND_PREV_UNCHAINED_FRAME(frame)	0

/* Define other aspects of the stack frame.  */

/* An expression that tells us whether the function invocation represented
   by FI does not have a frame on the stack associated with it. */
#define FRAMELESS_FUNCTION_INVOCATION(FI) \
  (frameless_look_for_prologue (FI))

/* Saved pc (i.e. return address).  */
#define FRAME_SAVED_PC(fraim) \
  (read_register_stack_integer ((fraim)->frame + (fraim)->rsize, 4))

/* Local variables (i.e. LOC_LOCAL) are on the memory stack, with their
   offsets being relative to the memory stack pointer (high C) or
   saved_msp (gcc).  */

#define FRAME_LOCALS_ADDRESS(fi) frame_locals_address (fi)
extern CORE_ADDR frame_locals_address ();

/* Return number of args passed to a frame.
   Can return -1, meaning no way to tell.  */
/* We tried going to the effort of finding the tags word and getting
   the argcount field from it, to support debugging assembler code.
   Problem was, the "argcount" field never did hold the argument
   count.  */
#define	FRAME_NUM_ARGS(fi) (-1)

#define FRAME_ARGS_ADDRESS(fi) FRAME_LOCALS_ADDRESS (fi)

/* Return number of bytes at start of arglist that are not really args.  */

#define FRAME_ARGS_SKIP 0

/* Provide our own get_saved_register.  HAVE_REGISTER_WINDOWS is insufficient
   because registers get renumbered on the a29k without getting saved.  */

struct frame_info;
void a29k_get_saved_register PARAMS ((char *raw_buffer, int *optimized, CORE_ADDR * addrp, struct frame_info * frame, int regnum, enum lval_type * lvalp));
#define GET_SAVED_REGISTER(raw_buffer, optimized, addrp, frame, regnum, lval) \
      a29k_get_saved_register (raw_buffer, optimized, addrp, frame, regnum, lval)

/* Call function stuff.  */
/* *INDENT-OFF* */
/* The dummy frame looks like this (see also the general frame picture
   above):

					register stack

	                	      |                |  frame for function
               	                      |   locals_sproc |  executing at time
                                      |________________|  of call_function.
                     		      |	               |  We must not disturb
                     		      |	args_out_sproc |  it.
        memory stack 		      |________________|
                     		      |____lr1_sproc___|<-+
       |            |		      |__retaddr_sproc_|  | <-- gr1 (at start)
       |____________|<-msp 0 <-----------mfp_dummy_____|  |
       |            |  (at start)     |  save regs     |  |
       | arg_slop   |		      |  pc0,pc1       |  |
       |            |		      |  pc2,lr0 sproc |  |
       | (16 words) |		      | gr96-gr124     |  |
       |____________|<-msp 1--after   | sr160-sr162    |  |
       |            | PUSH_DUMMY_FRAME| sr128-sr135    |  |
       | struct ret |                 |________________|  |
       | 17+        |                 |                |  | 
       |____________|<- lrp           | args_out_dummy |  |
       | struct ret |		      |  (16 words)    |  |
       | 16         |		      |________________|  |
       | (16 words) |                 |____lr1_dummy___|--+
       |____________|<- msp 2--after  |_retaddr_dummy__|<- gr1 after
       |            | struct ret      |                |   PUSH_DUMMY_FRAME
       | margs17+   | area allocated  |  locals_inf    |
       |            |                 |________________|    called
       |____________|<- msp 4--when   |                |    function's
       |            |   inf called    | args_out_inf   |    frame (set up
       | margs16    |                 |________________|    by called
       | (16 words) |                 |_____lr1_inf____|    function).
       |____________|<- msp 3--after  |       .        |
       |            |   args pushed   |       .        |
       |            |	              |       .        |
                                      |                |

   arg_slop: This area is so that when the call dummy adds 16 words to
      the msp, it won't end up larger than mfp_dummy (it is needed in the
      case where margs and struct_ret do not add up to at least 16 words).
   struct ret:  This area is allocated by GDB if the return value is more
      than 16 words.  struct ret_16 is not used on the a29k.
   margs:  Pushed by GDB.  The call dummy copies the first 16 words to
      args_out_dummy.
   retaddr_sproc:  Contains the PC at the time we call the function.
      set by PUSH_DUMMY_FRAME and read by POP_FRAME.
   retaddr_dummy:  This points to a breakpoint instruction in the dummy.  */
/* *INDENT-ON* */



/* Rsize for dummy frame, in bytes.  */

/* Bytes for outgoing args, lr1, and retaddr.  */
#define DUMMY_ARG (2 * 4 + 16 * 4)

/* Number of special registers (sr128-) to save.  */
#define DUMMY_SAVE_SR128 8
/* Number of special registers (sr160-) to save.  */
#define DUMMY_SAVE_SR160 3
/* Number of general (gr96- or gr64-) registers to save.  */
#define DUMMY_SAVE_GREGS 29

#define DUMMY_FRAME_RSIZE \
(4 /* mfp_dummy */     	  \
 + 4 * 4  /* pc0, pc1, pc2, lr0 */  \
 + DUMMY_SAVE_GREGS * 4   \
 + DUMMY_SAVE_SR160 * 4	  \
 + DUMMY_SAVE_SR128 * 4	  \
 + DUMMY_ARG		  \
 + 4 /* pad to doubleword */ )

/* Push an empty stack frame, to record the current PC, etc.  */

#define PUSH_DUMMY_FRAME push_dummy_frame()
extern void push_dummy_frame ();

/* Discard from the stack the innermost frame,
   restoring all saved registers.  */

#define POP_FRAME pop_frame()
extern void pop_frame ();

/* This sequence of words is the instructions
   mtsrim cr, 15
   loadm 0, 0, lr2, msp     ; load first 16 words of arguments into registers
   add msp, msp, 16 * 4     ; point to the remaining arguments
   CONST_INSN:
   const lr0,inf                ; (replaced by       half of target addr)
   consth lr0,inf               ; (replaced by other half of target addr)
   calli lr0, lr0 
   aseq 0x40,gr1,gr1   ; nop
   BREAKPT_INSN:
   asneq 0x50,gr1,gr1  ; breakpoint     (replaced by local breakpoint insn)
 */

#if TARGET_BYTE_ORDER == HOST_BYTE_ORDER
#define BS(const)	const
#else
#define	BS(const)	(((const) & 0xff) << 24) |	\
			(((const) & 0xff00) << 8) |	\
			(((const) & 0xff0000) >> 8) |	\
			(((const) & 0xff000000) >> 24)
#endif

/* Position of the "const" and blkt instructions within CALL_DUMMY in bytes. */
#define CONST_INSN (3 * 4)
#define BREAKPT_INSN (7 * 4)
#define CALL_DUMMY {	\
		BS(0x0400870f),\
		BS(0x36008200|(MSP_HW_REGNUM)), \
		BS(0x15000040|(MSP_HW_REGNUM<<8)|(MSP_HW_REGNUM<<16)), \
		BS(0x03ff80ff),	\
		BS(0x02ff80ff),	\
		BS(0xc8008080),	\
		BS(0x70400101),	\
		BS(0x72500101)}
#define CALL_DUMMY_LENGTH (8 * 4)

#define CALL_DUMMY_START_OFFSET 0	/* Start execution at beginning of dummy */

/* Helper macro for FIX_CALL_DUMMY.  WORDP is a long * which points to a
   word in target byte order; bits 0-7 and 16-23 of *WORDP are replaced with
   bits 0-7 and 8-15 of DATA (which is in host byte order).  */

#if TARGET_BYTE_ORDER == BIG_ENDIAN
#define STUFF_I16(WORDP, DATA) \
  { \
    *((char *)(WORDP) + 3) = ((DATA) & 0xff);\
    *((char *)(WORDP) + 1) = (((DATA) >> 8) & 0xff);\
  }
#else /* Target is little endian.  */
#define STUFF_I16(WORDP, DATA) \
  {
*(char *) (WORDP) = ((DATA) & 0xff);
*((char *) (WORDP) + 2) = (((DATA) >> 8) & 0xff);
}
#endif /* Target is little endian.  */

/* Insert the specified number of args and function address
   into a call sequence of the above form stored at DUMMYNAME.  */

/* Currently this stuffs in the address of the function that we are calling.
   Since different a29k systems use different breakpoint instructions, it
   also stuffs BREAKPOINT in the right place (to avoid having to
   duplicate CALL_DUMMY in each tm-*.h file).  */

#define FIX_CALL_DUMMY(dummyname, pc, fun, nargs, args, type, gcc_p)   \
  {\
    STUFF_I16((char *)dummyname + CONST_INSN, fun);		\
    STUFF_I16((char *)dummyname + CONST_INSN + 4, fun >> 16);	\
  /* FIXME  memcpy ((char *)(dummyname) + BREAKPT_INSN, break_insn, 4); */ \
  }

/* a29k architecture has separate data & instruction memories -- wired to
   different pins on the chip -- and can't execute the data memory.
   Also, there should be space after text_end;
   we won't get a SIGSEGV or scribble on data space.  */

#define CALL_DUMMY_LOCATION AFTER_TEXT_END

/* Because of this, we need (as a kludge) to know the addresses of the
   text section.  */

#define	NEED_TEXT_START_END 1

/* How to translate register numbers in the .stab's into gdb's internal register
   numbers.  We don't translate them, but we warn if an invalid register
   number is seen.  Note that FIXME, we use the value "sym" as an implicit
   argument in printing the error message.  It happens to be available where
   this macro is used.  (This macro definition appeared in a late revision
   of gdb-3.91.6 and is not well tested.  Also, it should be a "complaint".) */

#define	STAB_REG_TO_REGNUM(num) \
	(((num) > LR0_REGNUM + 127) \
	   ? fprintf(stderr, 	\
		"Invalid register number %d in symbol table entry for %s\n", \
	         (num), SYMBOL_SOURCE_NAME (sym)), (num)	\
	   : (num))

extern enum a29k_processor_types
{
  a29k_unknown,

  /* Bit 0x400 of the CPS does *not* identify freeze mode, i.e. 29000,
     29030, etc.  */
  a29k_no_freeze_mode,

  /* Bit 0x400 of the CPS does identify freeze mode, i.e. 29050.  */
  a29k_freeze_mode
}
processor_type;

/* We need three arguments for a general frame specification for the
   "frame" or "info frame" command.  */

#define SETUP_ARBITRARY_FRAME(argc, argv) setup_arbitrary_frame (argc, argv)
extern struct frame_info *setup_arbitrary_frame PARAMS ((int, CORE_ADDR *));