t1.lpj

实现基于ip2022的MPEG2 TS的IP组播接收

        object TRadioNode
          Name = 'Use Serializer 1'
          Description = 'Using SerDes1 to support this ipEthernet instance'
          DefineName = 'USE_S1_FOR_ETHERNET'
          FileName = '0'
          Lists = <>
          Value = True
          object TYesNoNode
            Name = 'Link LED'
            Description = 
              'Check to enable Ethernet link status indication LED. A steady on' +
              ' LED indicates a good link.'
            DefineName = '_S1_IPETHERNET_LINK_LED'
            FileName = '0'
            Lists = <>
            Value = True
            object TListNode
              Name = 'Port'
              Description = 'Port selection for link LED.'
              DefineName = '_S1_IPETHERNET_LINK_LED_PORT'
              FileName = '0'
              Lists = <>
              Value = 'RE'
              ListName = 'ALL_PORTS'
            end
            object TListNode
              Name = 'Pin'
              Description = 'Pin selection for link LED.'
              DefineName = '_S1_IPETHERNET_LINK_LED_PIN'
              FileName = '0'
              Lists = <>
              Value = '1'
              ListName = 'ALL_PINS'
            end
            object TYesNoNode
              Name = 'Active High'
              Description = 
                'Check this box to set active high for signal to drive this LED. ' +
                'Otherwise, the signal will be active low.'
              DefineName = '_S1_IPETHERNET_LINK_LED_HIGH'
              FileName = '0'
              Lists = <>
              Value = True
            end
          end
          object TYesNoNode
            Name = 'Activity LED'
            Description = 
              'Check to enable Ethernet activity indication LED. This LED flash' +
              'es for any data transfer activity (both RX and TX).'
            DefineName = '_S1_IPETHERNET_ACTIVITY_LED'
            FileName = '0'
            Lists = <>
            Value = True
            object TListNode
              Name = 'Port'
              Description = 'Port selection for activity LED.'
              DefineName = '_S1_IPETHERNET_ACTIVITY_LED_PORT'
              FileName = '0'
              Lists = <>
              Value = 'RE'
              ListName = 'ALL_PORTS'
            end
            object TListNode
              Name = 'Pin'
              Description = 'Pin selection for activity LED.'
              DefineName = '_S1_IPETHERNET_ACTIVITY_LED_PIN'
              FileName = '0'
              Lists = <>
              Value = '0'
              ListName = 'ALL_PINS'
            end
            object TYesNoNode
              Name = 'Active High'
              Description = 
                'Check this box to set active high for signal to drive this LED. ' +
                'Otherwise, the signal will be active low.'
              DefineName = '_S1_IPETHERNET_ACTIVE_LED_HIGH'
              FileName = '0'
              Lists = <>
              Value = True
            end
          end
          object TYesNoNode
            Name = 'Collision LED'
            Description = 
              'Check to enable Ethernet collision indication LED. This LED flas' +
              'hes when collision has been detected.'
            DefineName = '_S1_IPETHERNET_COLLISION_LED'
            FileName = '0'
            Lists = <>
            Value = True
            object TListNode
              Name = 'Port'
              Description = 'Port selection for collision LED.'
              DefineName = '_S1_IPETHERNET_COLLISION_LED_PORT'
              FileName = '0'
              Lists = <>
              Value = 'RE'
              ListName = 'ALL_PORTS'
            end
            object TListNode
              Name = 'Pin'
              Description = 'Pin selection for collision LED.'
              DefineName = '_S1_IPETHERNET_COLLISION_LED_PIN'
              FileName = '0'
              Lists = <>
              Value = '2'
              ListName = 'ALL_PINS'
            end
            object TYesNoNode
              Name = 'Active High'
              Description = 
                'Check this box to set active high for signal to drive this LED. ' +
                'Otherwise, the signal will be active low.'
              DefineName = '_S1_IPETHERNET_COLLISION_LED_HIGH'
              FileName = '0'
              Lists = <>
              Value = True
            end
          end
          object TYesNoNode
            Name = 'Combo Activity/Link LED'
            Description = 
              'Check to enable a combined Ethernet activity and link status ind' +
              'ication LED. This LED is steady to indicate a good link and flas' +
              'hes for any data transfer activity (both RX and TX).'
            DefineName = '_S1_IPETHERNET_COMBO_LED'
            FileName = '0'
            Lists = <>
            object TListNode
              Name = 'Port'
              Description = 'Port selection for combo activity/link LED.'
              DefineName = '_S1_IPETHERNET_COMBO_LED_PORT'
              FileName = '0'
              Lists = <>
              Value = 'RE'
              ListName = 'ALL_PORTS'
            end
            object TListNode
              Name = 'Pin'
              Description = 'Pin selection for combo activity/link LED.'
              DefineName = '_S1_IPETHERNET_COMBO_LED_PIN'
              FileName = '0'
              Lists = <>
              Value = '1'
              ListName = 'ALL_PINS'
            end
            object TYesNoNode
              Name = 'Active High'
              Description = 
                'Check this box to set active high for signal to drive this LED. ' +
                'Otherwise, the signal will be active low.'
              DefineName = '_S1_IPETHERNET_COMBO_LED_HIGH'
              FileName = '0'
              Lists = <>
              Value = True
            end
            object TExpressionNode
              Name = 'LED Duration'
              Description = 
                'Specifies the duration in Timer Ticks of the LED toggle.'#13#10#13#10'Time' +
                'r operation is supported by one_shot timer'
              DefineName = '_S1_IPETHERNET_COMBO_LED_DURATION'
              FileName = '0'
              Lists = <>
              Value = '50'
            end
          end
        end
        object TRadioNode
          Name = 'Use Serializer 2'
          Description = 'Using SerDes2 to support this ipEthernet instance'
          DefineName = 'USE_S2_FOR_ETHERNET'
          FileName = '0'
          Lists = <>
          object TYesNoNode
            Name = 'Link LED'
            Description = 
              'Check to enable Ethernet link status indication LED. A steady on' +
              ' LED indicates a good link.'
            DefineName = '_S2_IPETHERNET_LINK_LED'
            FileName = '0'
            Lists = <>
            Value = True
            object TListNode
              Name = 'Port'
              Description = 'Port selection for link LED.'
              DefineName = '_S2_IPETHERNET_LINK_LED_PORT'
              FileName = '0'
              Lists = <>
              Value = 'RF'
              ListName = 'ALL_PORTS'
            end
            object TListNode
              Name = 'Pin'
              Description = 'Pin selection for link LED.'
              DefineName = '_S2_IPETHERNET_LINK_LED_PIN'
              FileName = '0'
              Lists = <>
              Value = '5'
              ListName = 'ALL_PINS'
            end
            object TYesNoNode
              Name = 'Active High'
              Description = 
                'Check this box to set active high for signal to drive this LED. ' +
                'Otherwise, the signal will be active low.'
              DefineName = '_S2_IPETHERNET_LINK_LED_HIGH'
              FileName = '0'
              Lists = <>
              Value = True
            end
          end
          object TYesNoNode
            Name = 'Activity LED'
            Description = 
              'Check to enable Ethernet activity indication LED. This LED flash' +
              'es for any data transfer activity (both RX and TX).'
            DefineName = '_S2_IPETHERNET_ACTIVITY_LED'
            FileName = '0'
            Lists = <>
            Value = True
            object TListNode
              Name = 'Port'
              Description = 'Port selection for activity LED.'
              DefineName = '_S2_IPETHERNET_ACTIVITY_LED_PORT'
              FileName = '0'
              Lists = <>
              Value = 'RF'
              ListName = 'ALL_PORTS'
            end
            object TListNode
              Name = 'Pin'
              Description = 'Pin selection for activity LED.'
              DefineName = '_S2_IPETHERNET_ACTIVITY_LED_PIN'
              FileName = '0'
              Lists = <>
              Value = '4'
              ListName = 'ALL_PINS'
            end
            object TYesNoNode
              Name = 'Active High'
              Description = 
                'Check this box to set active high for signal to drive this LED. ' +
                'Otherwise, the signal will be active low.'
              DefineName = '_S2_IPETHERNET_ACTIVE_LED_HIGH'
              FileName = '0'
              Lists = <>
              Value = True
            end
          end
          object TYesNoNode
            Name = 'Collision LED'
            Description = 
              'Check to enable Ethernet collision indication LED. This LED flas' +
              'hes when collision has been detected.'
            DefineName = '_S2_IPETHERNET_COLLISION_LED'
            FileName = '0'
            Lists = <>
            Value = True
            object TListNode
              Name = 'Port'
              Description = 'Port selection for collision LED.'
              DefineName = '_S2_IPETHERNET_COLLISION_LED_PORT'
              FileName = '0'
              Lists = <>
              Value = 'RF'
              ListName = 'ALL_PORTS'
            end
            object TListNode
              Name = 'Pin'
              Description = 'Pin selection for collision LED.'
              DefineName = '_S2_IPETHERNET_COLLISION_LED_PIN'
              FileName = '0'
              Lists = <>
              Value = '6'
              ListName = 'ALL_PINS'
            end
            object TYesNoNode
              Name = 'Active High'
              Description = 
                'Check this box to set active high for signal to drive this LED. ' +
                'Otherwise, the signal will be active low.'
              DefineName = '_S2_IPETHERNET_COLLISION_LED_HIGH'
              FileName = '0'
              Lists = <>
              Value = True
            end
          end
          object TYesNoNode
            Name = 'Combo Activity/Link LED'
            Description = 
              'Check to enable a combined Ethernet activity and link status ind' +
              'ication LED. This LED is steady to indicate a good link and flas' +
              'hes for any data transfer activity (both RX and TX).'
            DefineName = '_S2_IPETHERNET_COMBO_LED'
            FileName = '0'
            Lists = <>
            object TListNode
              Name = 'Port'
              Description = 'Port selection for combo activity/link LED.'
              DefineName = '_S2_IPETHERNET_COMBO_LED_PORT'
              FileName = '0'
              Lists = <>
              Value = 'RF'
              ListName = 'ALL_PORTS'
            end
            object TListNode
              Name = 'Pin'
              Description = 'Pin selection for combo activity/link LED.'
              DefineName = '_S2_IPETHERNET_COMBO_LED_PIN'
              FileName = '0'
              Lists = <>
              Value = '5'
              ListName = 'ALL_PINS'
            end
            object TYesNoNode
              Name = 'Active High'
              Description = 
                'Check this box to set active high for signal to drive this LED. ' +
                'Otherwise, the signal will be active low.'
              DefineName = '_S2_IPETHERNET_COMBO_LED_HIGH'
              FileName = '0'
              Lists = <>
              Value = True
            end
            object TExpressionNode
              Name = 'LED Duration'
              Description = 
                'Specifies the duration in Timer Ticks of the LED toggle.'#13#10#13#10'Time' +
                'r operation is supported by one_shot timer'
              DefineName = '_S2_IPETHERNET_COMBO_LED_DURATION'
              FileName = '0'
              Lists = <>
              Value = '50'
            end
          end
        end
        object TSectionNode
          Name = 'RX polarity setting'
          Description = 
            'Configure RX polarity behavior here.'#13#10#13#10'The RX polarity can be f' +
            'ixed to support normal or inverted polarity to match board level' +
            ' design. It can also be set to dynamic polarity detection. Setti' +
            'ng to dynamic enables automatic RX polarity detection and relate' +
            'd polarity reversal at the expense of slightly lengthy ISR proce' +
            'ssing.'
          DefineName = 'UNNAMED'
          FileName = '0'
          Lists = <>
          object TRadioNode
            Name = 'Normal RX polarity'
            Description = 'Click here to enable normal RX polarity'
            DefineName = '_ETH_RX_NORMAL_POLARITY'
            FileName = '0'
            Lists = <>
            Value = True
          end
          object TRadioNode
            Name = 'Reversed RX polarity'
            Description = 'Click here to enable reversed RX polarity'
            DefineName = '_ETH_RX_REVERSED_POLARITY'
            FileName = '0'
            Lists = <>
          end
          object TRadioNode
            Name = 'Dynamic RX polarity'